Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree3265Likes

Thread: 55 Wagon Progress
          
   
   

Reply To Thread
Page 88 of 121 FirstFirst ... 38 78 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 98 ... LastLast
Results 1,306 to 1,320 of 1810
  1. #1306
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    McMaster Carr, we are going to make some “pressing” dies. When I get on a laptop later tonight I’ll post the mesh pn’s we used.
    cffisher and 40FordDeluxe like this.
    Robert

  2. #1307
    jerry clayton's Avatar
    jerry clayton is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2006
    Location
    Bartlett
    Posts
    6,831

    I like the mesh tables in MC cataloques because it shows the reduction in area related to various wire diameters and spacing per inch------
    cffisher and MP&C like this.
    By popular opinions-just a grumpy old man key board bully--But really, if you are going to ask for help on an internet site, at least answer questions about what you are asking about-----

  3. #1308
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Ryan, we used three different sizes just like the width of the trim rings were three different sizes, so they would be more proportional to the size of the speaker. This was 304 stainless ordered from McMaster Carr. They size by the number of square openings per inch, and the size of the wire. I started by getting their sample pack, good to have if you want to see size differences in person ( or to show customers). PN of sample is 9231T11. For the large bass speaker we used 5x5 mesh size (5 openings per inch) PN is 85385T31. For mid’s we used 8x8 mesh, PN is 85385T42. For tweeters we used 10x10 mesh, PN is 85385T48.
    40FordDeluxe likes this.
    Robert

  4. #1309
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    I'd never have thought to use different sizes mesh. Neat idea. I like them at 45*
    MP&C likes this.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

  5. #1310
    cffisher's Avatar
    cffisher is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Constantine
    Car Year, Make, Model: 57 chevy 2 dr wagon
    Posts
    9,476

    Been using McMaster Carr for over45 years now great place for things others don't have and they are very reasonable
    MP&C, 40FordDeluxe and RichB like this.
    Charlie
    Lovin' what I do and doing what I love
    Some guys can fix broken NO ONE can fix STUPID
    W8AMR
    http://fishertrains94.webs.com/
    Christian in training

  6. #1311
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    Thanks Robert. I've been trying to find some SS mesh to put in front of condensers etc to keep them from getting clogged with bug guts. Everything I've found has had too large of holes. I didn't think of them.
    MP&C likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  7. #1312
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Quote Originally Posted by cffisher View Post
    Been using McMaster Carr for over45 years now great place for things others don't have and they are very reasonable
    And usually very speedy with the shipping too!
    cffisher and MP&C like this.

  8. #1313
    Scrubline's Avatar
    Scrubline is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2019
    Location
    Cleveland
    Car Year, Make, Model: '23 T bucket
    Posts
    21

    Impressive work, MP&C. Your build thread commentary and pictures are an inspiration to those like me (garage hacks) and to guys that do this stuff professionally. I feel like heading to the garage and working on my t bucket..... even though it's past my bedtime.
    MP&C and 40FordDeluxe like this.

  9. #1314
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Thanks to all for their input on the speaker grilles, the owner has decided on the 45* rotation. Our other choice to ponder was whether to use chrome, polished, or brushed finish. We clamped some of the rings in the lathe and gave it a brushed finish, others were polished so we can compare..















    Here it was decided to go with the polished over brushed, and for ease of maintenance, we opted for chrome plating. So all the holes were drilled, counterbored, and transferred to their respective mounting location. The tweeter trim rings will be held in place with 6-32 hardware, the mids use 8-32, and the sub uses 10-32. Rivet nuts were installed where needed..























    With the trim rings ready to send for plating, we turned our attention to the fuel lines, where we wanted a direct run all the way to the tank. Our bending efforts found Mike in a bit of a stretch..







    The fuel line passes behind the body mount, we have a heat deflector in place where it passes over the tail pipe, and then it will connect directly to the tank. They will be secured with adel clamps fastened to the floor braces from underneath. Return line in place, supply line to go:



    https://www.youtube.com/watch?v=ZbUxujdz2PU






    .
    NTFDAY, cffisher, stovens and 1 others like this.
    Robert

  10. #1315
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    You're showing off.

    Don't stop!
    stovens and MP&C like this.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

  11. #1316
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    More great work. So you're chroming the rings after the brushed work was done? I really like your body mold trick to make the lines too.
    MP&C likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  12. #1317
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Yes, the samples of each were just done to show the owner the comparison.
    Robert

  13. #1318
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Had a slight distraction yesterday, a couple hood sides for a 37 Ford showed up. The owner wanted to remove the side "grille", and add a tapered recess pan with clamshell louvers. Here's what we started with...







    Some cutoff wheel action later....







    In an attempt to keep as much metal on the ends as possible, we opted to flatten the sad remains of the horizontal fins. This involved some shrinking via the heating tip in the dent puller..












    Looks like someone has spilled bondo all over this panel. Funny the inside didn't look all that mangled to warrant the amount we found.. Must be a TV car..


    The shrinking efforts flattened out the ends fairly well...












    I filled in the previous trim holes with 18 Ga plugs and TIG fusion while the owner worked away at removing the bondo so we could see what we had to work with...



















    Next, we had to fold a flange in the front and extend the factory bead around the opening down the front where we had flattened the panel. Some of the existing bead profiles had seen better days in the past 80 plus years, so I checked a set of joggle dies I had made for drip rail as it looked close...











    New flange folded at the front, bead added using the Lennox, original beads touched up ...















    Tapered pan fabricated.....







    Louver layout











    Welded in place..







    He is having some art deco style trim pieces made to accent the louvers down the center, topped by 62 Impala fender trim. We didn't have those, so here it is with alternate SS fuel line for your viewing pleasure...











    NTFDAY, DennyW, cffisher and 4 others like this.
    Robert

  14. #1319
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    Very nice and fast work! Were they bad under the filler?
    MP&C likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  15. #1320
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Yep, amazing piece of work. I couldn't "see" that outcome in a decade! Way cool.
    stovens and MP&C like this.

Reply To Thread
Page 88 of 121 FirstFirst ... 38 78 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 98 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink