Thread: Aftermarket dipsticks

Tweet

After two fancy Lokar transmission dipsticks, the first with the single 'O' ring as the seal, the second, replaced under warranty is their modified version with two, and I still have a drool of ATF. Of course, since the car is only marking its spot, I probably shouldn't worry about it, but those oily spots in the drive as well as the puddle in the garage are getting to be a PITA. And yes, I have tried different kinds of silicone sealant - and none works as I can't really get that area totally clean and dry while in the car. If the tranny was out and on my work bench, I could probably come up with something, but not as installed.

I went through the Summit catalog and there are probably a dozen different versions for a C4 by ATI, Hughes, Moroso and Miloden as well as Lokar just to name a few manufacturers. Most of these have something that looks similar to a PCV valve cover seal and others have a locking handle as well - which looks like a good addition. Now, my question, have any of you folks ever used any of these other versions besides Lokar? Did they leak? Can one of them be bent if needed to fit my well recessed engine?

Oh well - I know Ford components - and not a BB (belly button) part so I just ordered a Hughes from Summit and will mod if necessary. Thanks for lookin' anyhow

Dave i've not had problems with the real lokar sticks but there are a lot of copys of Lokars out there and they never seem to seal correctly. I have got them to seal by installing slightly thicker O rings, HTH

Originally Posted by roadster32

Dave i've not had problems with the real lokar sticks but there are a lot of copys of Lokars out there and they never seem to seal correctly. I have got them to seal by installing slightly thicker O rings, HTH

Steve - when Lokar sent me the second, I was able to put a little bit larger O-rings on but the grooves need to be opened some for even larger and right now, all my tools aren't handy. The hole in the case almost seems like it was enlarged a little.

I know a lot of people use silicone on them Dave but i've found it makes the situation worse, i fit them with a smear of grease, but the cheap copys won't seem to seal with anything. Annoying having oil leaks isn't it

Originally Posted by roadster32

I know a lot of people use silicone on them Dave but i've found it makes the situation worse, i fit them with a smear of grease, but the cheap copys won't seem to seal with anything. Annoying having oil leaks isn't it

Steve - I wouldn't have any complaint if it was a cheap knock off. It is an $100+/- Lokar firewall mount and installed per their instructions with just a little bit of silicone - their verbal instructions. This is the only component on the car that has leaked - ever. I wont even tell you how many pan gaskets it took - that real narrow cut out place on the pan rail just wouldn't seal so I ended up with a new pan, flanged bolts instead of my ARP $tuds plus a very thick cork gasket instead of my favorite neoprene composition Fel-Pro's. Now, that first pan - a TCI, was not even flat at that cut out. I ended up with a Spectre Performance 5455 from Summit - and it is a nice part.

Dip sticks are a pain in the butt, I've actully cut a washer looking gasget out of a thin wall inner tube before and used that with a slightly worn dip stick tube.
It sealed up good and never leaked.
It got a problem right now with the after market dip stick that came with my Canton 8 qt. oil pan. Instead of putting a threaded nut at a angle so the stick can go down in to the oil they put the threaded nut straite out of the side so the dip stick goes straite in side ways. Stupid Design!!! I tried to used the factory dip stick on the front of the motor but that hits the windage tray screen and won't go thru. So I now have to take the pan off and drill the screen so the engine wiil except the stock dip stick.
I spent about $700 bucks on the set up and they can't make a dip stick that works with thier pan. Kurt

Originally Posted by vara4

It got a problem right now with the after market dip stick that came with my Canton 8 qt. oil pan. Instead of putting a threaded nut at a angle so the stick can go down in to the oil they put the threaded nut straite out of the side so the dip stick goes straite in side ways. Stupid Design!!! I tried to used the factory dip stick on the front of the motor but that hits the windage tray screen and won't go thru. So I now have to take the pan off and drill the screen so the engine wiil except the stock dip stick.
I spent about $700 bucks on the set up and they can't make a dip stick that works with thier pan. Kurt

Are you sure that threaded boss on the side is not there for a turbo oil return line? My SBF pan has an "extra" boss in the side, too, but the builder says that it is put there because so many of the aftermarket applications run turbo's, and it's easier to put in a plug on the side than to have two designs. You might ask Canton about theirs?