Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree260Likes

Thread: 1947 Biederman Truck Fender Repairs
          
   
   

Reply To Thread
Page 10 of 10 FirstFirst ... 2 3 4 5 6 7 8 9 10
Results 136 to 150 of 150
  1. #136
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    More progress on the hood, here is the other end of the hood brace.





    Looking at the back side, you can see where a few holes were welded closed the last time it was painted, and the severe pitting and new holes that we have. A testament to the fact that what shows is always the tip of the iceberg. Although better than the passenger side, this is definitely one of those "while we are here" things. Do it right, do it once. (grinder marks were mine)








    With our new replacement all one piece, the next step is to bend the flange that spot welds to the hood skin. A tipping wheel in the Fasti-werks bead roller makes quick work of it. The bend line was transposed from the original and an initial pass under the tipping die marks the crease line a bit better, Then successive passes are made, lifting slightly with each pass. This is done until the beads interfere with the tipping die.










    Then the partial bent flange is clamped in the magnetic brake for the remainder of the fold. This brake allows us to use a die on either side of the bead details, where a full die may inadvertently push in on the beads.








    End gets cut to length and marked for initial trimming








    Looks like we may have enough bead stock left for another couple of ends.






    That's where we left off yesterday, we'll see about welding the new end on today..



    .
    NTFDAY and 40FordDeluxe like this.
    Robert

  2. #137
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Our last end for the hood brace. Off with the old.....





    Then it gets trimmed to our scribe line and the end media blasted in prep for welding. Our new end is test fit and trimmed until we get the right distance to our reference marks. The "batwings" give us a heat sink at the edge for less chance of burning back the edge at the weld.





    The center rib is aligned both on the sides and the face, and tacked in position using the TIG.





    The pieces are aligned as we work outward, tacking as we go. A "corking tool" is used as a dolly where any bumping may be needed for alignment.








    Tacked...





    Welded....





    Welds cleaned up and end angles compared..










    Now we can get back to straightening sheet metal..
    NTFDAY, cffisher, 34_40 and 3 others like this.
    Robert

  3. #138
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    We have a few more spots to fix from cracking and fatigue, namely the holes on the underside for the rubber hood bumpers. We've already repaired three, and from the looks of it, need to take care of the remaining three..











    18 Gauge x 1/4" plugs were TIG welded in to fill the existing holes, and a copper backer gives us a bit of a heat sink so the cracks/fatigued areas don't blow a big hole on us..











    Welds were dressed on both sides of the sheet metal, and new holes drilled slightly in farther from the edge to help slow down the reappearance of cracks.











    Next, I'm sure everyone has seen how these hoods can oil can, show low spots, and try to flop around while driving down the road. Part of that is abuse over the years, fatigue, etc. Any low spots invariably result in a loss of support of the hood and will show oil cans or loose areas.





    A good tool to check the crown of the hood is a long straight edge in the form of a 36" rule. If you don't have one, most hardware stores sell aluminum flat bar for a few dollars that will make a good profile template. For this style hood, lows are bad, straight is better, and a slight crown in the center crease along the entire length of the "flat" area of the hood is optimal.. This gives the support to help eliminate those oil cans and floppy hoods.


    When we started there was an obvious area about 12" forward of the rear edge, dead center, that appears low, and was easily pushed downward. In order to better define the center crease and provide the support needed, we will use a sand bag (a rather large one) and lightly hammer from the bottom side into said bag with a purpose built "punch".











    In order to keep the back portion of the hood down against the bag for support, we used our latest "metalshaping" tool to hold the front of the hood up, an engine hoist..





    A reference mark is used on the inside, measured and centered...





    The crease was checked for low spots prior, and the bottom marked. The "punch" is dragged along the centerline and tapped as you go. Flip the hood over, check crown, remark as needed, repeat. We got to a good straight/slight crown and the oil can disappeared. Pushing along the entire center crease was a nice tight support now..








    So if you are having issue with your hood, I would suggest first checking your center crease.
    40FordDeluxe and 36 sedan like this.
    Robert

  4. #139
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    More awesome work and great tips too!
    MP&C likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  5. #140
    v8nutz's Avatar
    v8nutz is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2016
    Location
    rocklin
    Posts
    565

    If only I had a gigantic sand bag like that.
    MP&C likes this.

  6. #141
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Thanks Guys!!


    The 51 F7 hood is closer to reuniting with the brace with the newly repaired ends.. Epoxy primer will be under the brace this time around to help prevent the new side patches from rusting again..

















    Some blocking tips on the F7 hood. We have a nice crease on the inside of the hood from front to back. These scratches show that we would be taking material off the adjacent side if no other steps were taken to stop our sanding block at the center of the crease...





    By adding a strip of tape along the center, it gives us a positive stop for the sanding block..





    Then switching for the other side....





    Which leaves us a nice crease in the middle, and panels nice and flat to either side...





    Final blocking on the inside using tape to keep the center line sharp, then brace welded in place and some epoxy touch ups done..











    With the touch ups blocked, we're ready for some Epoxy/sealer, some PPG ESSS base, and my first time spraying SPI Universal... WooHoo! love this clear!!





    These Ford truck hoods can be a pain to get good paint coverage inside the nose.. So a couple pieces of TIG wire from our rack to the hood brackets hold it up in the air so we can get into the nose with the spray gun..





    NTFDAY, 40FordDeluxe and 36 sedan like this.
    Robert

  7. #142
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Thought I'd do a progression of pictures to show the carnage we started with on the hood brace to where it was painted this past weekend....





    https://www.youtube.com/watch?v=NDZyTTuUGVE











    Note the wings left adjacent to the weld to act as heat sinks and prevent the edge from burning back...











    No Body filler, just epoxy primer, basecoat, and clearcoat. Looks almost factory!!


    NTFDAY, johnboy, cffisher and 1 others like this.
    Robert

  8. #143
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    So every time we place the hood on my folding stand, the hood skin deflects upward at those pressure points (corners). Which means that won't work for blocking out the hood. So lets' use the same supports that the hood uses and make a blocking "stand".

    Large 5/8" bolt through the hood latch hole for supporting the nose...





    And going through our scrap inventory, here's some tubing we used for the back end, bolted into the hinge support. The extra "feet" help to stabilize it so the sanding effort won't try and flop it over...














    With that done, all our open holes are taped over and the entire bottom side masked off to protect the inside finish..








    A bit of Evercoat 416 to address some lows, and 3 coats of SPI epoxy for the next round of blocking on the outside.








    Blocking...





    Some booth clean up and fresh masking on the table, hood pre-cleaned and tacked.....





    Sealed with SPI Epoxy thinned about 10%





    Fleet paint that was used originally on the truck, supplied by owner. Orange peel in a can..





    2 coats of color, 2 coats of SPI Universal Clear...





    NTFDAY, cffisher, 34_40 and 1 others like this.
    Robert

  9. #144
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    "Orange Peel in a can".... rotflomao!
    NTFDAY, MP&C and 36 sedan like this.

  10. #145
    johnboy is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2005
    Location
    Tataraimaka NZ
    Car Year, Make, Model: `47 Ford sedan, A.C.Cobra replica.
    Posts
    2,630

    Quote Originally Posted by 34_40 View Post
    "Orange Peel in a can".... rotflomao!
    Brought a smile to my dial too.
    NTFDAY, 34_40, MP&C and 1 others like this.
    johnboy
    Mountain man. (Retired.)
    Some mistakes are too much fun to be made only once.
    I don't know everything about anything, and I don't know anything about lots of things.

    '47 Ford sedan. 350 -- 350, Jaguar irs + ifs.
    '49 Morris Minor. Datsun 1500cc, 5sp manual, Marina front axle, Nissan rear axle.
    '51 Ford school bus. Chev 400 ci Vortec 5 sp manual + Gearvendors 2sp, 2000 Chev lwb dually chassis and axles.
    '64 A.C. Cobra replica. Ford 429, C6 auto, Torana ifs, Jaguar irs.

  11. #146
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    This past Friday night we cut and buffed the F7 hood to get rid of some dust nibs, and Saturday morning Jared and I started to reassemble the hood. The horn wiring had some dry and cracking insulation sleeving, so it was replaced as well.








    John stopped by mid morning and we got all the parts put back together and adjusted. Looks much better with the hood back on, John has been driving without one for a couple months.














    All ready for the Tri-state Antique Truck Show this week in Clear Brook VA..
    Mike P, NTFDAY and rspears like this.
    Robert

  12. #147
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,989

    That is a fine looking truck! Ya' did good, Robert, but then we all know you always do!
    MP&C likes this.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  13. #148
    v8nutz's Avatar
    v8nutz is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2016
    Location
    rocklin
    Posts
    565

    That truck is way to beautiful to use as a truck. Great work!
    MP&C likes this.

  14. #149
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    times 3... great work as always. congrats to the crew!
    MP&C likes this.

  15. #150
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Quote Originally Posted by v8nutz View Post
    That truck is way to beautiful to use as a truck. Great work!

    OK, just to show that this truck does work on occasion, John got the it loaded up today, ready for departing tomorrow for the show at the Frederick County Fairgrounds in Clear Brook, VA. I may have to take a ride on Friday and check out the show..


    NTFDAY and 34_40 like this.
    Robert

Reply To Thread
Page 10 of 10 FirstFirst ... 2 3 4 5 6 7 8 9 10

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink