Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree3265Likes

Thread: 55 Wagon Progress
          
   
   

Reply To Thread
Page 84 of 121 FirstFirst ... 34 74 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 94 ... LastLast
Results 1,246 to 1,260 of 1810
  1. #1246
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    I did have quite a bit of 3/16 rod left over from our Metalshaping class last year. It's coming in handy!
    34_40 and 40FordDeluxe like this.
    Robert

  2. #1247
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Happy Thanksgiving everyone!



    Had a request to show how the inside corners were tipped for wire edging the AC condenser opening. Here's a video (with poor audio.. iPhone seems to want to do a noise cancelling) that shows stretching the inner corners. I do spend a bit more time and accuracy on the real part, this was a quick, down and dirty demonstration.



    https://www.youtube.com/watch?v=bkfr...ature=youtu.be



    We drilled out mounting hole pattern in the AC condenser to the radiator, and added AVK style rivet nuts to the radiator cross bars to secure..











    Installed, this will be the profile of the upper mounting bracket (about 24+ inches wide), that will share the AC condenser upper mounting screws. Not sure if we want to do this in polished stainless or paint. Thoughts?






    The upper bracket will be attached to the core support also using rivet nuts, mainly from the back side to hide some of the hardware..







    Last edited by MP&C; 11-23-2018 at 08:28 AM.
    randyr and 40FordDeluxe like this.
    Robert

  3. #1248
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    Very nice work and thanks for the video! You just showed me how I can put a flange on a inner corner on a piece of sheet metal! I never thought to cut down a tube like that and use it as a die. That's great!

    How much other shiny aluminum/ss will you have under the hood?
    randyr likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  4. #1249
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Ryan, I think we will be mostly paint other than chrome valve covers, etc. on the engine. Alternator brackets, etc will likely be powder-coated. So that has me leaning toward painting body color or something...



    So this weekend I worked on the "new" dolly to remove some of the rust..







    Started with the media blaster to remove all the rust and scale...












    Next, the pits were removed using 60 grit roloc sanding discs, followed by brown, red, and then blue scotchbrite discs. Then some media blasting to give a good finish..






    Lastly, some 320 on the DA to remove scratches from the dolly face, and a trip to the pedestal buffer with some thick gloves.






    All that fun aside, back on radiator mounts. The upper will be a combination mount and also cover for the top of the core support. This will be 44" long, so to help the magnetic brake make some more crisp bends we'll thin the bend lines in the Lennox using a tipping die. the 44" length on the panel is a bit long for my 48" linear slide, so another section is added to give us 96" to play with. Just clears the Pexto shear..










    Motion picture of the process:



    https://www.youtube.com/watch?v=rCxakebyQzs



    Bend lines in place ....











    ….and we left off there for some turkey dinner. Should get it trimmed on the sides and folded up this Tuesday night.
    NTFDAY, randyr, stovens and 2 others like this.
    Robert

  5. #1250
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    Nice work on that dolly! I'm sure you have some time in getting it all smoothed back out. I think body color will look the best on the cover panel. Nice start to the panel too.
    MP&C likes this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  6. #1251
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Our 18 Gauge upper radiator mount / core support cover is cut out and bent to fit. Still needs some minor trimming around the radiator top and then we’ll make some threaded spotters to mark our rivet-nut holes.















    https://www.youtube.com/watch?v=5ZbACO-IHY4



    .
    NTFDAY, cffisher, stovens and 1 others like this.
    Robert

  7. #1252
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    Well as normal, one change leads to one or more others. We thought we'd test fit to check out the clearance for the hood latch striker out in front of the AC condenser.








    I missed getting a picture of our attempt, but here's a view of the original from the service manual.







    No way the original latch striker will work with the AC condenser that far forward. So we filled in the rear bolt hole and bent the latch striker as close as we could to the latch hole, which gave us 1-1/2” more room.











    The support structure would no longer have the rear bolt hole in the same location, and we needed to slim it down to the same width as the modified striker...







    Next, the rear bolt for the striker will need to be horizontal now, so a stud is fabricated and welded in place, and the support bracket modified for this bolting arrangement as well.



















    Media blasted....










    test fit....



    https://www.youtube.com/watch?v=d5iE1T77WHQ



    .......and on to the next hurdle
    NTFDAY and 40FordDeluxe like this.
    Robert

  8. #1253
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    I took delivery the other day on a set of slide tracks so we used the opportunity to get the Arbor Press metalshaping dies from Pat Brubaker mounted under the table for better use of space. We used the Diacro press brake to bend some 1/8" aluminum for making some angle brackets for mounting.








    For those with a Diacro manual press brake, be aware the factory cast parts may not be 100% compatible with cheater bars. This happened a few months back, and our billet steel replacement is holding up much better, still has yet to transfer the problem farther down the line, knock on wood.











    E got the holes drilled out in the brackets, and I assembled the pieces..







    This is much better.. a good start to cleaning off the table..




    https://www.youtube.com/watch?v=i65pvDZGzio



    A demo of the process of using the arbor press....



    https://www.youtube.com/watch?v=MUQghpUVohU



    .....and then today, Mike and I worked on blocking and straightening out the roof to get it a bit closer for painting.







    We did find a stretched spot in the roof, and chased it around a few times in using the body hammer and shot bag. No matter what we did, it tended to still have an up and down wave, so too much metal. The roof has been covered in SPI Epoxy for a while and I had no intention of removing the epoxy, so we opted for the donut dolly (this one home made) as it would leave the paint intact over using a torch....







    Part of the difficulty in using the donut dolly is insuring the hammer aligns with the dolly for the most effective shrink.







    So we employed our magnet trick seen here:



    https://www.youtube.com/watch?v=Ubq89aPMJjY



    .......once the trouble areas needing a bump outward were located (they were stretched inward), the magnet was placed directly over the spots and then we could trace the locations on the inside for proper hammer strike while the donut dolly was held over the corresponding location on the outside. This was about the best results I've had using the donut dolly.



    Here are a few of the shrink locations used to straighten out the roof and its waves...







    Mike P, NTFDAY, 53 Chevy5 and 4 others like this.
    Robert

  9. #1254
    stovens's Avatar
    stovens is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2007
    Location
    Petaluma
    Car Year, Make, Model: 48 Ford F1
    Posts
    9,778

    You guys are amazing!
    MP&C likes this.
    " "No matter where you go, there you are!" Steve.

  10. #1255
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    yeah, what he said. Amazing!
    Thanks (as always) for sharing the knowledge..
    MP&C likes this.

  11. #1256
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    https://www.youtube.com/watch?v=pTp3yWKFTdk



    Had a couple questions about the donut dolly. Basically this is just like off dolly but on steroids, as supporting the panel surrounding the hammer strike gives a much more effective capture and shrink of the dent. This also helps to explain why alignment of the hammer to the dolly is so critical, and why the magnet alignment trick I showed in the earlier post works so well to make your shrinking more effective. The dolly should always be placed on the concave side to be able to hammer into the dolly and bring the panel back straight. For a larger, more pronounced dent I’ll use a flat hammer, like the Snap-on BF603. If the panel is wavy but still somewhat flat, then I’ll use a crowned hammer such as the Snap-on BF618. Use caution with the crowned hammer to not hit hard enough to add a dent, ideally we want to hit so that the metal pushes slightly into the dolly but the springback would bring it back to flush. (This comes with experience) It’s at this point that the donut dolly is most effective.

    The video shown simulates using a flat faced hammer on a large radius/dent. This could be used to remove the dent altogether, or perhaps just reduce the sharpness of the radius, like the rear roof corner on a Model A. None of the tools we have will do everything, but I’ve found the donut dolly especially useful in shrinking where you don’t want to use heat (torch).
    Robert

  12. #1257
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    More progress on the wagon, we are adding a second interior light, so an original was sourced so they would match...









    .....and media blasted, ready for primer..









    Gary dropped off the rear seat so we could match drill holes into the side bolsters and install 5/16 rivet nuts for attachment..














    And we found another low spot in the roof, likely due to media blasting the light bracket too close to the roof skin. We used the rare earth magnet trick to accurately locate the inside to outside for exact alignment of the hammer to the donut dolly..









    outside, where we used the donut dolly to hammer into...














    ....and the inside, where we use the crowned hammer.....














    Using this method we were able to locate, layout, and bump all of the low spots to a consistent crown to match the surrounding panel, all in less than 5 minutes. In this case, a much better option than mixing and sanding filler.




    This video better shows the concept..




    https://www.youtube.com/watch?v=HHHT...ature=youtu.be
    NTFDAY, 53 Chevy5, randyr and 2 others like this.
    Robert

  13. #1258
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Quote Originally Posted by MP&C View Post
    More progress on the wagon, we are adding a second interior light, so an original was sourced so they would match... all in less than 5 minutes. In this case, a much better option than mixing and sanding filler.
    A second lamp? Why of course!
    and with some "careless" editing.. For giggles I went back to the first post in this thread.. January, 2013.. Wow.. Doesn't seem like it's been that long.

    As always, thanks for sharing the knowledge.
    53 Chevy5, stovens, Jack F and 1 others like this.

  14. #1259
    MP&C's Avatar
    MP&C is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2008
    Location
    Leonardtown
    Car Year, Make, Model: Walking
    Posts
    1,204

    It does to me!
    53 Chevy5, 34_40 and stovens like this.
    Robert

  15. #1260
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    Man, you do great work. I can just see myself making that little low spot a surface similar to a golf ball in 5 minutes and being mad and making 24hrs more work for myself.
    cffisher and MP&C like this.
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

Reply To Thread
Page 84 of 121 FirstFirst ... 34 74 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 94 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink