55 Wagon Progress

Jack, with housing stationary and wheels rotated, we did see a bit of fluctuation of about +/- .005 to .010, but it was rather sporadic and not relative to the welded pads. When the tires where stationary and the housing was rotated around, before our heating efforts the runout started at about +/- .050, and was directly related to the welded pad location. At the point the housing was being rotated, the dial indicator remained in the same spot on the wheel, so although the wheel isn't perfect, the reading should have reflected housing issues only.

Robert, thanks for that explanation. :) I learned something new.:) :)


Jack.

Well Kyle was mostly on his own tonight as I had some repairs to do on the wife's vehicle..


New U-bolts came in yesterday, they have a pretty good selection on their web site if anyone needs some....


http://i5.photobucket.com/albums/y16...ure%203997.jpg



Threads taped off and all the parts media blasted...


http://i5.photobucket.com/albums/y16...ure%203994.jpg


http://i5.photobucket.com/albums/y16...ure%203996.jpg


Then Kyle got the rear torn down for media blasting as well. Blast cabinet just the right size..


http://i5.photobucket.com/albums/y16...ure%203998.jpg


http://i5.photobucket.com/albums/y16...ure%203999.jpg

Some Hoosier Profile parts showed up for the new wheeling machine.. Joe Andrews does some real nice work..


http://i5.photobucket.com/albums/y16...ure%204001.jpg

Getting things ready for the next round of SPI epoxy, here hanging the 9" rear on the multi-purpose rotisserie a-frame..


http://i5.photobucket.com/albums/y16...ure%204007.jpg


http://i5.photobucket.com/albums/y16...ure%204008.jpg


We had this bare spot after the last time we blocked, and had bumped it a bit with the flat body hammer.


http://i5.photobucket.com/albums/y16...ure%204009.jpg


Doesn't look like it did much to rectify the issue, let's look further....


http://i5.photobucket.com/albums/y16...ure%204012.jpg


Looks like the rear end of the inside bracket is pushing a bit on the skin, no wonder the hammer didn't do much. Time to find the tool for the job, a pair of crimping pliers for stove pipe/ductwork.....


http://i5.photobucket.com/albums/y16...ure%204013.jpg


http://i5.photobucket.com/albums/y16...ure%204014.jpg


That should give us some breathing room, and bumped it again with the hammer.


Put the SPI in the paint shaker, should have tapped the lid a bit tighter..


http://i5.photobucket.com/albums/y16...ure%204015.jpg


More parts ready for spraying....


http://i5.photobucket.com/albums/y16...ure%204017.jpg


http://i5.photobucket.com/albums/y16...ure%204018.jpg


After 3 coats of epoxy....


http://i5.photobucket.com/albums/y16...ure%204019.jpg


http://i5.photobucket.com/albums/y16...ure%204020.jpg


http://i5.photobucket.com/albums/y16...ure%204021.jpg


http://i5.photobucket.com/albums/y16...ure%204022.jpg


http://i5.photobucket.com/albums/y16...ure%204026.jpg


http://i5.photobucket.com/albums/y16...ure%204027.jpg


http://i5.photobucket.com/albums/y16...ure%204028.jpg


Here's some of the "restraint" methods for painting the small parts....


http://i5.photobucket.com/albums/y16...ure%204023.jpg


http://i5.photobucket.com/albums/y16...ure%204024.jpg


http://i5.photobucket.com/albums/y16...ure%204025.jpg


Here clamps for the tie rod ends are held in a twisted loop..


http://i5.photobucket.com/albums/y16...ure%204029.jpg


http://i5.photobucket.com/albums/y16...ure%204030.jpg


I think the fenders should be good for wet sanding after this go round:


https://www.youtube.com/watch?v=wHrxzkEc618




.

Crimping pliers. So that's what those are.

I've got a pair, I expected to find what they're for eventually.

They come in handy in putting stovepipe together when the one end needs to be a bit smaller.. ;)



Well we didn't get many pictures tonight, but we've got the frame back on 4 wheels!


http://i5.photobucket.com/albums/y16...ure%204034.jpg

Well after the weekend off for the Snowmaggedon, back at more parts prep for the next round of primer..

Kyle did some media blasting on the steering box and other parts while I blocked out the inside of the hood and the hood brace..


http://i5.photobucket.com/albums/y16...ure%204036.jpg


http://i5.photobucket.com/albums/y16...ure%204038.jpg


http://i5.photobucket.com/albums/y16...ure%204040.jpg


Then Kyle worked on degreasing and scuffing the trans...


http://i5.photobucket.com/albums/y16...ure%204041.jpg

For those that followed the Louver job on the 35 Chevy hood sides, Cody Walls (the builder) and Dave Thomas (the owner) will at the Grand National Roadster Show Jan 29-31. The 35 will be the feature car in The Rodder's Journal booth in building 4, so if you're going be sure to stop by and check out Cody's craftsmanship and attention to detail.. absolutely beautiful car..


TRJ will also have a full feature article in the next issue.


http://i5.photobucket.com/albums/y16...CodyWalls.jpeg

That is simply beautiful! Fantastic metal work, and the louvers on the hood are a defining feature, in my eye. You're making me wonder why I'm not traveling to California for the weekend!

Quote:

---

Originally Posted by rspears

That is simply beautiful! Fantastic metal work, and the louvers on the hood are a defining feature, in my eye. You're making me wonder why I'm not traveling to California for the weekend!

---

I'm already here and planning to check it out....:D

Randy, get plenty of pictures!

Quote:

---

Originally Posted by MP&C

Randy, get plenty of pictures!

---

... and of Ken Thurm's new coupe, too!!

Quote:

---

Originally Posted by randyr

I'm already here and planning to check it out....:D

---

:rolleyes: And I'm not saying a word!! :rolleyes::eek::rolleyes::eek::D

A much over looked detail. You must have some circle track racing in your resume. :) Referring to you rear end straightening post.