Yes and yes...
Printable View
Yes and yes...
Robert, PM me details I'd like to buy a 3xl if you have them in fat kid sizes. :LOL:
Yes, up to 3X..
Well time to finish up Randy's scooter fender(s). The original (rear) had been loose at some point as the fender mounting holes were nice and elongated from flopping around. So I'll get them filled in and Randy will need to match drill them to the frame..
http://i5.photobucket.com/albums/y16...ure%203549.jpg
http://i5.photobucket.com/albums/y16...ure%203550.jpg
Use the right tools for the job :headscrat
http://i5.photobucket.com/albums/y16...ure%203553.jpg
After marking, when cutting out such a small piece I like to leave a "handle" until the very end..
http://i5.photobucket.com/albums/y16...ure%203554.jpg
http://i5.photobucket.com/albums/y16...ure%203555.jpg
....gives you something to hold onto while fine tuning the fit
http://i5.photobucket.com/albums/y16...ure%203556.jpg
Nice and snug....
http://i5.photobucket.com/albums/y16...ure%203558.jpg
Tacking in the filler piece...
http://i5.photobucket.com/albums/y16...ure%203560.jpg
http://i5.photobucket.com/albums/y16...ure%203559.jpg
http://i5.photobucket.com/albums/y16...ure%203561.jpg
http://i5.photobucket.com/albums/y16...ure%203563.jpg
http://i5.photobucket.com/albums/y16...ure%203565.jpg
Next was to trim a nice radius on the front and back ends of the new front fender....
http://i5.photobucket.com/albums/y16...ure%203567.jpg
http://i5.photobucket.com/albums/y16...ure%203569.jpg
Last on the list, the forming process with the old fender left some "pie crust" edging, as seen here and in an original photo...
http://i5.photobucket.com/albums/y16...ure%203572.jpg
http://i5.photobucket.com/albums/y16...ure%203571.jpg
So we needed a special tool in order to duplicate this feature...
http://i5.photobucket.com/albums/y16...ure%203574.jpg
http://i5.photobucket.com/albums/y16...ure%203575.jpg
Spacing all marked out....
http://i5.photobucket.com/albums/y16...ure%203576.jpg
Finished edge...
http://i5.photobucket.com/albums/y16...ure%203577.jpg
http://i5.photobucket.com/albums/y16...ure%203578.jpg
http://i5.photobucket.com/albums/y16...ure%203579.jpg
All ready for delivery!
So cool to be able to do what you do!
X2! Amazing to watch you guys create.
As always, thanks for sharing the pics and your knowledge.
Thanks!
Kyle was off tonight so I missed getting some in-process pictures.. Still cleaning up welds to get the body ready for media blasting. The rear brackets for the gas tank straps were welded in...
http://i5.photobucket.com/albums/y16...ure%203582.jpg
http://i5.photobucket.com/albums/y16...ure%203583.jpg
I also worked on the passenger quarter this evening. One of the biggest problems with welding a horizontal seam down through the middle of the quarter on a car is the tendency for the seam to cave inwards.. I had some help this evening using the Watervliet hammer and a 24" radius die..
http://i5.photobucket.com/albums/y16...ure%203591.jpg
Still have some highs and lows to address, but the weld seam is back out close to where it should be, and the Atlantic Ocean has calmed quite a bit..
http://i5.photobucket.com/albums/y16...ure%203590.jpg
Next was to remove some creases in the cowl vent, seen here...
http://i5.photobucket.com/albums/y16...ure%203584.jpg
http://i5.photobucket.com/albums/y16...ure%203585.jpg
Looks like someone may have kneeled on it at some point in the last 60 years. I've found the easy way to "highlight" an area like this in need of repair is to use a piece of 80 grit on the back side:
http://i5.photobucket.com/albums/y16...ure%203587.jpg
http://i5.photobucket.com/albums/y16...ure%203589.jpg
Got the creases out using the body hammer with the chisel tip, and forgot to get the finished pictures. Next time...
Here's the top side of the cowl vent.....
http://i5.photobucket.com/albums/y16...ure%203607.jpg
....using this hammer....
http://i5.photobucket.com/albums/y16...ure%203609.jpg
the marks on the back side show where the strikes were placed to remove the creases...
http://i5.photobucket.com/albums/y16...ure%203610.jpg
Kyle has the inner roof insulation about gone...
http://i5.photobucket.com/albums/y16...ure%203611.jpg
Great Pics.. Thanks.
And the shop looks like it's stayin' clean.:LOL:
We're trying to stay on top of it. Upright vacuum cleaner helps out ;)
Our enclosed trailer has the white wagon wheels that always seem to turn rusty in a few years, so I have been trying different wheels to see what might work....
These are some late model Mustang wheels, the hub hole would need to be opened slightly, but the offset was, well off.
http://i5.photobucket.com/albums/y16...ure%203619.jpg
Perhaps on a fancy trailer with more stainless trim, but these just looked too much. Next, some plain Jane Ford Ranger wheels....
http://i5.photobucket.com/albums/y16...ure%203620.jpg
Much better, correct offset, and no wheel modification needed. Just need to change up the color and add some stainless trim rings. I do have some bright orange, some bright red, and a few other colors in the paint locker..
Some before and after media blasting..
http://i5.photobucket.com/albums/y16...ure%203615.jpg
http://i5.photobucket.com/albums/y16...ure%203616.jpg
Two down, two to go, and then we'll get some SPI epoxy on there for some rust preventative measure. Can't get it all done in one night. And more weld grinding and other prep work on the wagon continues. Since the big cleanup in preparation for the class in the shop earlier this month, we haven't been able to find our quarter panel profile template, so Kyle made a couple of them, one for in front of the rear wheel, one behind, and we've been working on the weld seams and doing some metal bumping to minimize our stock in filler products. Drivers side is looking much better than it did last week, still about another day to go and the quarters should be good for epoxy primer..
http://i5.photobucket.com/albums/y16...ure%203617.jpg
http://i5.photobucket.com/albums/y16...ure%203618.jpg
That quarter looks amazing! Great work!
Yep.. that's the word.. AMAZING!
Thanks guys, but I think the camera was being kind. We do have some highs/lows to still address, but it's getting much closer to ready for epoxy...
Stopped by my brother in law's and took delivery of the rotisserie for the frame, he had been using it for his ElCamino...
http://i5.photobucket.com/albums/y16...ure%203626.jpg
And Kyle cut some adapter angles out of a piece of 4 x 6 tubing...
http://i5.photobucket.com/albums/y16...ure%203628.jpg
Well, we didn't get pictures of the funny part. Kyle and I loaded the frame in the trailer and headed off to the local car wash to remove the grease from the front cross member. We had quite a few stares and a couple horns honking as he pushed the frame around the car wash parking lot and I was sitting on the frame rail, maneuvering with the Jr. steering wheel. We found the tire presoak and a wire brush does wonders for the engine grease. The car wash attendant did not look too pleased, but never said a word.
Back at the shop, bolting the adapter plates onto the frame...
http://i5.photobucket.com/albums/y16...ure%203633.jpg
http://i5.photobucket.com/albums/y16...ure%203639.jpg
You can see in the above picture we used 1-1/2" long spacers to get a better access for media blasting the frame..
Disassembly starts....
http://i5.photobucket.com/albums/y16...ure%203649.jpg
http://i5.photobucket.com/albums/y16...ure%203651.jpg
http://i5.photobucket.com/albums/y16...ure%203652.jpg
http://i5.photobucket.com/albums/y16...ure%203653.jpg
After a few revolutions and a bit of air pressure, we had quite a pile of 60 year old dirt..
http://i5.photobucket.com/albums/y16...ure%203654.jpg
Override springs from the era. The handyman wagons were often used as work vehicles, and this option helped with the heavy loads...
http://i5.photobucket.com/albums/y16...ure%203655.jpg
All stripped....
http://i5.photobucket.com/albums/y16...ure%203658.jpg
http://i5.photobucket.com/albums/y16...ure%203661.jpg
Had a early Chevy hood side show up at the shop tonight, the owner wanted a couple different versions of louver samples made up that he could hold against the hood on the car to better visualize. One style he was looking at lends from an early Alfa Romeo that extends the louvers onto the cowl, as shown in the green tape..
http://i5.photobucket.com/albums/y16...ure%203663.jpg
We took a paper pattern of the details so the hood side could go back with him to use as a pattern for the opposite side that still needs to be made.
http://i5.photobucket.com/albums/y16...ure%203664.jpg
http://i5.photobucket.com/albums/y16...ure%203665.jpg
Spot welded on some "end stops" for the louver die.....
http://i5.photobucket.com/albums/y16...ure%203667.jpg
.....and a squared plate for the back gauge.
http://i5.photobucket.com/albums/y16...ure%203668.jpg
http://i5.photobucket.com/albums/y16...ure%203669.jpg
Louvers in the Lennox.....
http://i5.photobucket.com/albums/y16...ure%203670.jpg
http://i5.photobucket.com/albums/y16...ure%203671.jpg
http://i5.photobucket.com/albums/y16...ure%203672.jpg
http://i5.photobucket.com/albums/y16...ure%203674.jpg
One sample down, one to go..
That's very cool! I had never really thought about forming long louvers, and had no idea that they were done with a set of small dies, moved side to side. Makes perfect sense, but I'd assumed that one had to have a pair of dies for the louver to press it in one action, which makes no sense now that I've seen the actual process. Thanks once again for posting the pictures in sufficient detail to learn from.
I'd only seen a picture of Von Dutch punching louvers, and I believe he used a large punch and die setup. Looks like the old analogy of skinning cats holds true yet again.