-
-
-
Thanks!
Tonight's post offers some blocking pointers.
We had already done a couple sessions of priming/blocking the door across to the quarter and to the fender, all installed on the car. After this, more primer and put a perimeter of tape on the door skin. Now block separately, and the tape allows you to block the door and keep off the edge to prevent losing your match to the fender/quarter.
http://i5.photobucket.com/albums/y16...ure%203031.jpg
I don't stick with 45* angles, if you want to keep a long direction flat, you need the long block to better follow that direction. So change up to some sharper angles, about 30* off the long direction every now and then. Work one end to the other, consistent spacing, consistent angle, end to end. Then alternate to passes in the opposite direction.
Once done, and the inner part is good and blocked, now remove the tape and GENTLY block to the edge, taking care to not pull down at the edge and round things back off again. Whatever hand is holding the block make sure it is minimal pressure and stays on the door skin. In other words, no pressure pulling down past the edge.
http://i5.photobucket.com/albums/y16...ure%203034.jpg
One other point, to keep the inner end of the sanding block from sanding out all your hard work in the center of the door, put a wrap of tape around the end of the sanding block that is towards the center of the door. This helps that end to glide across the center of the door without cutting primer there.
http://i5.photobucket.com/albums/y16...ure%203033.jpg
http://i5.photobucket.com/albums/y16...ure%203036.jpg
Now to show the importance of the long board..
We had done some blocking with the 27" AFS and seemed to have two high spots with a low in the middle of the door..
Note the high areas marked by the green tape...
http://i5.photobucket.com/albums/y16...ure%203024.jpg
http://i5.photobucket.com/albums/y16...ure%203026.jpg
Now we can see that as the sander is moved to the left, the left portion of the AFS is over the high spot on the left, and a bit more movement and the right portion of the AFS will start dropping into the low void. Effectively, this is still cutting material out of the low, keeping it low.
http://i5.photobucket.com/albums/y16...ure%203028.jpg
Looking at the next size up, a 36" AFS....
http://i5.photobucket.com/albums/y16...ure%203019.jpg
http://i5.photobucket.com/albums/y16...ure%203020.jpg
Here we can see this one does a much better job of spanning the high spots and staying up on top, for a more effective job of knocking down the highs and leaving the low in the center alone...
http://i5.photobucket.com/albums/y16...ure%203029.jpg
After a few horizontal passes at slight angles, like so with the 36".......
http://i5.photobucket.com/albums/y16...ure%203018.jpg
We follow up with some vertical passes at slight angles with the 27".... all rods removed to better follow the contour. Then alternate back to the 36 and another horizontal session..
http://i5.photobucket.com/albums/y16...ure%203030.jpg
-
Nice work Robert! Are you seeing a light at the end of the tunnel now? :LOL: The motorcycle turned out awesome! That's a bad deal about the halo! Like you said though, at least you found it. That would be a bad deal to find it after it's painted.
-
We can see the light, but it's still a bit dim! :LOL:
-
thanks for the posting I like being educated on this stuff, thanks again !
-
-
Thanks fellas!
Well there has been a slight break in the updates, as I've been in Okinawa for about a month. Not to fear, Kyle has been plugging away on the wagon, it even has a floor in it, as you can see here...
http://i5.photobucket.com/albums/y16...ure%203051.jpg
http://i5.photobucket.com/albums/y16...ure%203053.jpg
He did get a quite a bit of blocking done while I was gone....
http://i5.photobucket.com/albums/y16...ure%203045.jpg
http://i5.photobucket.com/albums/y16...ure%203059.jpg
http://i5.photobucket.com/albums/y16...ure%203060.jpg
And did get some wet sanding done on a few of the interior trim pieces. Today he started on the rear floor, part of the problem with welding a flat plate is that it doesn't stay flat. The plug welds to secure the floor to the bracing beneath caused some shrinking, which resulted in the metal between bulging outward, some up, some down. Looks about like the Atlantic on a calm day.
http://i5.photobucket.com/albums/y16...ure%203054.jpg
http://i5.photobucket.com/albums/y16...ure%203056.jpg
Today, as I was going to be wet sanding, he was going to try some torch shrinking. To better make this a one person job with minimal risk of open flame, we thought to give the "electric" torch a go.
http://i5.photobucket.com/albums/y16...ure%203063.jpg
http://i5.photobucket.com/albums/y16...ure%203061.jpg
The plastic dust pan served as a tray to hold the wet rag, keeping it in closer proximity to where it was needed and attempt to limit the amount of water elsewhere. The results showed quite an improvement, and it's in need of some bumping at this point..
http://i5.photobucket.com/albums/y16...ure%203064.jpg
But alas, the gas tank is in the way, so we will likely get the body back on the rotisserie here soon in an effort to get the remaining prep prior to paint completed.
Meanwhile, I was wet sanding and couldn't find the squeegee, so a trip to the local Ace Hardware at lunch, and we had a replacement. Works well, and no metal hardware on this new one to add any scratches....
http://i5.photobucket.com/albums/y16...ure%203067.jpg
http://i5.photobucket.com/albums/y16...ure%203068.jpg
Exterior of the hood is about done...
http://i5.photobucket.com/albums/y16...ure%203069.jpg
http://i5.photobucket.com/albums/y16...ure%203070.jpg
-
I've received some PM's on occasion asking about fixing oil cans on sheet metal, so I thought I'd share some ideas....
I've seen on far too many automotive forums that any request for help dealing with an oil can invariably generates a response to pick up the shrinking disc, despite no detailed information given besides "I have an oil can"
Before I suggest to someone how to fix an oil can, it is best to find out what kind of oil can you are dealing with, first and foremost. I consider there are two kinds, a tight oil can and a loose oil can, each will require a different method of repair.
Tight oil can:
This is almost exclusively caused by body damage, whether a dent, glancing crease, or media blast damage, and is especially noted by displaced metal that will oil can when considerable pressure is applied, and may or may not forcibly spring back. When the body damage occurs, it stretches the panel throughout the dent or crease. A typical dent, whether straight in or a glancing blow, will have direct and indirect damage. The direct damage goes inward, stretching the panel as it goes. The indirect damage, is a much lesser amount of springback, compounded by the internal stretch pushing outward circumferentially, and you will see an outward bulge around the perimeter of the dent/damage. Although the initial inclination may be to shrink this outward bulge, for the most part this adjacent area is relatively damage free, it is mainly being spread outward by the stretch forcing outward. Shrinking the center damage will start the process of relieving the stresses pushing outward, relaxing some of the bulge surrounding the dent. After a bit of shrinking, using the shot bag against the outside of the crease/dent and some light taps with a flat body hammer or slapper from the inside will help to start manipulating the crease/dent back into it's original place. I would add that too much shrinking all at once may give you the loose oil can, so profile templates are highly recommended as they work well to let you see how the panel is reacting so you don't go too far too quick.
Tight oil can, part two:
Where some tight oil cans from dents may be challenging to determine where to start your shrinking (if it doesn't have an obvious sharp crease to show where to work from) the following process will normally find the area that needs shrinking.... Cycle the oil can in and out a couple times in order to find the outer perimeter. If it helps to mark it with some painters tape, a sharpie, so be it, use whatever works. Now using your thumb from one hand apply slight pressure on a point on this perimeter. Use the other hand to cycle the oil can again, using the same pressure as before. Keep moving your pressure point around the perimeter and cycle the oil can for each spot until you get to a point on the perimeter where the pressure will keep the oil can from cycling, it locks it from moving. This should identify your "sweet spot" that needs shrinking, and there may be more than one sweet spot
Loose oil can:
This is typically caused by welding, over-eager torch shrinking, or shrinking something when you should have stretched, (or fatigue over the many years that has caused a larger panel/hood to settle). Any panel will shrink from heat, causing the crown to draw in from the surrounding area. This is especially noted by a loose, easily flopped back and forth oil can. This is fixed by stretching, typically in the area of the weld and HAZ.
Loose oil can part two:
In some cases we'll see that a dent (or tight oil can) has actually caused a loose oil can in the outer reaches in the adjacent area. The direct force (dent) may have caused displacement of the inherent stresses of the panel (crown) such that it pulled at the adjacent metal elsewhere, resulting in a loose oil can outside the area of the dent. Here the loose oil can should be left alone and focus on removing the stretched area (dent) that moved the panel. Once the dent is removed, this action alone should correct the loose oil can in the adjacent area.
-
Nice work and thanks for the info and tips!
-
What great posts,I always learn something from them!
Thanks for taking the time to share your experience!
And people wonder why good paint jobs cost so much.
Labor,labor, labor!
Rich
-
Looks good keep up the good work!
-
-
Wow your attention to detail just never stops, excellent work
-