-
We noticed the driver's side hood gap was a bit tight and then noticed a difference in the end plates on the core support. The driver's side appears bent straight, so some hammer action made them more consistent and helped out the gap issue..
http://i5.photobucket.com/albums/y16...ure%202038.jpg
http://i5.photobucket.com/albums/y16...ure%202039.jpg
http://i5.photobucket.com/albums/y16...ure%202040.jpg
After checking the hood brace to core support for any fitment issues, we noticed some cutouts that will allow the air around the radiator. This opening, although minimal, was re-formed with a couple of fancy chisels..
http://i5.photobucket.com/albums/y16...ure%202027.jpg
http://i5.photobucket.com/albums/y16...ure%202028.jpg
http://i5.photobucket.com/albums/y16...ure%202029.jpg
http://i5.photobucket.com/albums/y16...ure%202030.jpg
http://i5.photobucket.com/albums/y16...ure%202031.jpg
The excess metal ruffles were addressed easily with the kick shrinker...
http://i5.photobucket.com/albums/y16...ure%202032.jpg
http://i5.photobucket.com/albums/y16...ure%202033.jpg
The next opening was a bit more substantial, and would require some replacement metal. Here was our first attempt at a bead along the edge of the panel..
http://i5.photobucket.com/albums/y16...ure%202036.jpg
The dies would not permit quite enough length, so we used a vee die off the press brake and a 1/2" steel rod to make a radius die for the mag brake..
http://i5.photobucket.com/albums/y16...ure%202041.jpg
http://i5.photobucket.com/albums/y16...ure%202042.jpg
...and between that and a straight die in the press brake, the edge bead was formed...
http://i5.photobucket.com/albums/y16...ure%202045.jpg
...here transposing the crease locations...
http://i5.photobucket.com/albums/y16...ure%202043.jpg
http://i5.photobucket.com/albums/y16...ure%202044.jpg
To pre-stretch the areas for the diagonal vee beads, we loaded these in the bead roller....
http://i5.photobucket.com/albums/y16...ure%202046.jpg
http://i5.photobucket.com/albums/y16...ure%202047.jpg
This didn't appear to add enough stretch, so the linear stretch die was used in the Watervliet planishing hammer....
http://i5.photobucket.com/albums/y16...ure%202048.jpg
http://i5.photobucket.com/albums/y16...ure%202049.jpg
Vee was added using 3/4 wide female bead die and a narrow tipping die..
http://i5.photobucket.com/albums/y16...ure%202050.jpg
A bit of heat was added to make it a bit easier to transition the round and vee beads together...
http://i5.photobucket.com/albums/y16...ure%202053.jpg
http://i5.photobucket.com/albums/y16...ure%202054.jpg
http://i5.photobucket.com/albums/y16...ure%202055.jpg
http://i5.photobucket.com/albums/y16...ure%202056.jpg
....and this one we'll get formed up on Wednesday night and get both welded in place...
http://i5.photobucket.com/albums/y16...ure%202057.jpg
-
Great work as usual!
Rich
-
-
-
Great work. It's pieces like this that a real tri 5 guy will have to know aren't stock to notice something isn't right because your work looks better than factory.
-
Thanks fellas!
I had a bit of a short night as I had to pick up the young'n from after school activities, so most of the progress this evening was Kyle's efforts.
Making the patch for the center relief, starting with adding the radius to the bottom edge... This uses a bottom vee die from the Diacro and a 1/2" rod to form the radius..
http://i5.photobucket.com/albums/y16...ure%202058.jpg
http://i5.photobucket.com/albums/y16...ure%202059.jpg
Test fit of the radius...
http://i5.photobucket.com/albums/y16...ure%202060.jpg
Trimming out the hood brace...
http://i5.photobucket.com/albums/y16...ure%202061.jpg
Scribing the patch....
http://i5.photobucket.com/albums/y16...ure%202064.jpg
Trimming some of the excess on the bandsaw, and then fine tuning with the snips....
http://i5.photobucket.com/albums/y16...ure%202066.jpg
http://i5.photobucket.com/albums/y16...ure%202067.jpg
http://i5.photobucket.com/albums/y16...ure%202068.jpg
I did work a bit more on hood gaps.. an official gap gauge shown here....
http://i5.photobucket.com/albums/y16...ure%202073.jpg
http://i5.photobucket.com/albums/y16...ure%202075.jpg
Also took some radiator leak preventative measures....
http://i5.photobucket.com/albums/y16...ure%202069.jpg
http://i5.photobucket.com/albums/y16...ure%202070.jpg
Trimming the other patch for the hood brace....
http://i5.photobucket.com/albums/y16...ure%202072.jpg
Kyle persuading the patch's crease over a bit. This uses a glancing blow to keep the crease's new location from sliding down on the anvil...
http://i5.photobucket.com/albums/y16...ure%202071.jpg
Both pieces clamped in place, we'll get some welding done on Saturday...
http://i5.photobucket.com/albums/y16...ure%202076.jpg
-
Today Kyle needed to start some welding on the hood brace, so while he was getting set up with the welder, I started making him an anvil that he could use to planish the weld dots inside the radius voids..
Heat applied...
http://i5.photobucket.com/albums/y16...ure%202085.jpg
http://i5.photobucket.com/albums/y16...ure%202086.jpg
http://i5.photobucket.com/albums/y16...ure%202087.jpg
http://i5.photobucket.com/albums/y16...ure%202090.jpg
http://i5.photobucket.com/albums/y16...ure%202092.jpg
http://i5.photobucket.com/albums/y16...ure%202093.jpg
Kyle's first job at welding sheet metal, he's a quick learner. He did have a couple spots that didn't like the heat and blew a hole, but he did a real nice job in getting those fixed as well.
http://i5.photobucket.com/albums/y16...ure%202089.jpg
Planishing weld dots on the new "anvil"..
http://i5.photobucket.com/albums/y16...ure%202095.jpg
Full weld penetration...
http://i5.photobucket.com/albums/y16...ure%202096.jpg
http://i5.photobucket.com/albums/y16...ure%202097.jpg
While he welded away, I turned my attention to the front end. The passenger door had a bit of a tight spot to the rear edge of the fender while opening.. Using a hack saw blade as a "feeler gauge", it was tight in one area. To help out the situation, time for another tool. I have a dent puller with a small pair of vise grips permanently attached, so we just need an adapter kit...
This was some leftover square tubing scraps...
http://i5.photobucket.com/albums/y16...ure%202101.jpg
http://i5.photobucket.com/albums/y16...ure%202100.jpg
In use..
http://i5.photobucket.com/albums/y16...ure%202102.jpg
After the pulling effort, the tight gap was well over two HSB thicknesses.
http://i5.photobucket.com/albums/y16...ure%202111.jpg
Moving on to other fender fitment, the bottom edge of the fender was higher than the adjacent rocker. Any adjustment was futile as the bolt was at the bottom of the adjustment hole. Time for some die grinder action to bring the hole downward and also flatten the bottom edge of the hole so any movement forward or backward doesn't push the bolt upward..... This was done on both fenders..
http://i5.photobucket.com/albums/y16...ure%202112.jpg
http://i5.photobucket.com/albums/y16...ure%202113.jpg
http://i5.photobucket.com/albums/y16...ure%202114.jpg
Test fit shows much better alignment.. This may be why the 57 went to a square hole..
http://i5.photobucket.com/albums/y16...ure%202115.jpg
Kyle done with his welding on the center patch, just needs to be dressed with the sanding disc. We'll save that for after the other patch gets welded in place..
Front:
http://i5.photobucket.com/albums/y16...ure%202116.jpg
Rear:
http://i5.photobucket.com/albums/y16...ure%202117.jpg
And I was also busy making more dust... Can't wait for springtime and the leaf blower :LOL:
http://i5.photobucket.com/albums/y16...ure%202118.jpg
http://i5.photobucket.com/albums/y16...ure%202119.jpg
http://i5.photobucket.com/albums/y16...ure%202120.jpg
http://i5.photobucket.com/albums/y16...ure%202121.jpg
-
Someone noticed we use some rather "vintage" ice picks as scribes for metalwork, and asked to see a closer look.. I had picked these up a few years ago at an auction as my wife looks at me with that "and why do we need those" looks... The one came shorter as shown, but to prolong the life of the picks, sharpen with a very fine file, never use a grinder ;)
The auction was in Fredericksburg VA, if anyone recognizes any of the old ice plants, be sure to chime in so we can all get a history lesson. I tried calling them but nobody answered 8 or 30.. :whacked:
http://i5.photobucket.com/albums/y16...ure%202131.jpg
http://i5.photobucket.com/albums/y16...ure%202132.jpg
http://i5.photobucket.com/albums/y16...ure%202133.jpg
http://i5.photobucket.com/albums/y16...ure%202134.jpg
http://i5.photobucket.com/albums/y16...ure%202135.jpg
http://i5.photobucket.com/albums/y16...ure%202136.jpg
-
Great finds. I too use some older tools in the shop. Lately at estate sales the kids and grand kids practically give away heirloom tools because they have no concept of quality or history, and probably never turned a wrench in their lives! My gain, but I always feel sad for the departed ones who spent a lifetime using and caring for these!
-
Great work! It's looking nice and tight! :LOL:
-
Thanks for the comments!
Kyle finishing up on the hood brace....
http://i5.photobucket.com/albums/y16...ure%202122.jpg
http://i5.photobucket.com/albums/y16...ure%202123.jpg
Because he had gaps to contend with, we used some copper to insure less chance of blow outs. A piece of 1/2" copper pipe was flattened and bent in the press brake to make a fitted backing for the vee bead detail..
http://i5.photobucket.com/albums/y16...ure%202124.jpg
http://i5.photobucket.com/albums/y16...ure%202137.jpg
http://i5.photobucket.com/albums/y16...ure%202142.jpg
http://i5.photobucket.com/albums/y16...ure%202145.jpg
http://i5.photobucket.com/albums/y16...ure%202146.jpg
Just a bit of work with the sander and this part should be done. Like the new look without all the gaping holes..
Meanwhile, I continued to make dust. Here's a good view of the built in "guide coat" feature of the SPI. Blocking on the top of the hood shows a low spot.....
http://i5.photobucket.com/albums/y16...ure%202140.jpg
And with just a couple scuffs from the bottom, the low shows up there as well
http://i5.photobucket.com/albums/y16...ure%202141.jpg
Just a few bumps with the hammer from the bottom into the small shot bag on top and the low is gone.
And the rest looks pretty much the same other than the piles of dust on the floor moving around.. :LOL:
http://i5.photobucket.com/albums/y16...ure%202139.jpg
-
A while back we had made the brackets to make up three "reproduction" battery trays based on a 1955 Chevy factory air conditioned car.
http://i5.photobucket.com/albums/y16...Picture782.jpg
The only part that did not come with the used original pieces we had as patterns was the factory hold down with it's attached "zee" bracket that secures the battery hold down to the rear of the core support, as seen here in the factory assembly bulletin.
http://i5.photobucket.com/albums/y16...ure%201999.jpg
We recently mocked up the battery location, and made a zee bracket based on the picture and the dimensions we had in front of us.
http://i5.photobucket.com/albums/y16...ure%202148.jpg
http://i5.photobucket.com/albums/y16...ure%202147.jpg
Now to make the remaining two brackets for the other two battery trays.. A roll former die in the press brake was used to make the vertical bends.
http://i5.photobucket.com/albums/y16...ure%202149.jpg
A bit of tipping using a press brake die as an anvil, and then using the tipping tool...
http://i5.photobucket.com/albums/y16...ure%202150.jpg
http://i5.photobucket.com/albums/y16...ure%202151.jpg
The finished brackets and a comparison....
http://i5.photobucket.com/albums/y16...ure%202152.jpg
http://i5.photobucket.com/albums/y16...ure%202153.jpg
http://i5.photobucket.com/albums/y16...ure%202154.jpg
http://i5.photobucket.com/albums/y16...ure%202155.jpg
-
Not much to show on our progress today, but here's Kyle finishing up the hood brace..
http://i5.photobucket.com/albums/y16...ure%202156.jpg
http://i5.photobucket.com/albums/y16...ure%202157.jpg
http://i5.photobucket.com/albums/y16...ure%202158.jpg
While I continue to generate dust on the floor...
http://i5.photobucket.com/albums/y16...ure%202159.jpg
Recently we installed a used core support that was quite a bit nicer than our original, but still showed some issues...
http://i5.photobucket.com/albums/y16...ure%202160.jpg
Here we see some rust...
http://i5.photobucket.com/albums/y16...ure%202161.jpg
And not quite enough clearance to the petcock..
http://i5.photobucket.com/albums/y16...ure%202163.jpg
So this will be next on the list, cutting out a new one with a bit better fitment.
-
We had an early schedule today to try and miss the weather.. As I still hadn't finished blocking the front end, rather than pull the core support just yet, Kyle will start on the rear of the wagon in wrapping up some details there. Before pulling the tailgate, there was one gap that was inconsistent, so I gave him a hand with the rework before he got welding..
http://i5.photobucket.com/albums/y16...ure%202165.jpg
http://i5.photobucket.com/albums/y16...ure%202166.jpg
First to unfold the flange a bit...
http://i5.photobucket.com/albums/y16...ure%202168.jpg
http://i5.photobucket.com/albums/y16...ure%202167.jpg
Next, some 14 gauge steel was cut out and a strengthening bend added to use for some friendly persuasion..
http://i5.photobucket.com/albums/y16...ure%202169.jpg
http://i5.photobucket.com/albums/y16...ure%202170.jpg
Refolded...
http://i5.photobucket.com/albums/y16...ure%202172.jpg
For comparison, before:
http://i5.photobucket.com/albums/y16...ure%202166.jpg
After:
http://i5.photobucket.com/albums/y16...ure%202171.jpg
Then we tweaked the twist of the tailgate for good fitment to the opening and Kyle added three plug welds down each side to lock the skin to the inner tail gate.
http://i5.photobucket.com/albums/y16...ure%202173.jpg
http://i5.photobucket.com/albums/y16...ure%202174.jpg
...Then we removed the tail gate so he could finish the plug welds for the top flange of the tail pan, I had only tacked it in place when the tailpan was installed, so this should help check off another item from the list......
Meanwhile I continued blocking out the front end..
http://i5.photobucket.com/albums/y16...ure%202176.jpg
http://i5.photobucket.com/albums/y16...ure%202177.jpg
http://i5.photobucket.com/albums/y16...ure%202178.jpg
http://i5.photobucket.com/albums/y16...ure%202179.jpg
-
Nice work. Mr.Customer should love this thing.