Robert, does anything ever have you stumped? Love following this thread.;):):)
Jack.
Printable View
Robert, does anything ever have you stumped? Love following this thread.;):):)
Jack.
Thanks guys. Sometimes I look forward to that being backed in a corner... gets the McGuyver ideas going!
We like the McGyuyver solutions too! :) But you always seem to have more than a swiss army knife in the tool box! ;)
Very nice work! I agree the way you pop off new tools for your work is amazing. I always try to think of a way but some times the idea just doesn't pop out and look as sweet as yours. :LOL:
McGuyver 100, Corner 0.;):):)
Jack.
Here's a few MacGuyver quotes for you,
"Well, when it comes down to me against a situation, I don't like the situation to win." - MacGyver (The Road Not Taken)
"It's kinda interesting how you can put one thing with another and cook up the right formula for stayin' out of trouble." - MacGyver (For Love or Money)
"One of my biggest problems is I can never leave a puzzle alone." - MacGyver (Ghost Ship)
and my favorites
"For the past seven years I have done nothing but travel around the world getting shot up, locked up, blown up ... and all I have to show for it are a couple of empty rolls of duct tape." - MacGyver (Friends)
"It's a little recipe I use in emergencies." - MacGyver, explaining the fertilizer bomb he's making (Last Stand)
:LOL: Those are pretty good..
Today we worked on hood and gap alignment at the front of the car, the passenger side is all but done, so we started around to the driver's side. The windshield cowl showed a high spot behind the fender and door, that was bulged about 3/16. Good ol' factory fit!
http://i5.photobucket.com/albums/y16...icture1328.jpg
So we made a vertical slice behind the fender and door, bumped the high spot down, and welded the joint.
We had a blowout near the leaded seam due to some rust that had collected on the back side.. Forgot to take a picture before slicing and dicing, but here's the culprit. Also had some porosity in the vertical weld that got cleaned out and re-welded later...
http://i5.photobucket.com/albums/y16...icture1331.jpg
Fitted, tacked, and finished
http://i5.photobucket.com/albums/y16...icture1333.jpg
http://i5.photobucket.com/albums/y16...icture1334.jpg
http://i5.photobucket.com/albums/y16...icture1336.jpg
http://i5.photobucket.com/albums/y16...icture1337.jpg
Gaps...
http://i5.photobucket.com/albums/y16...icture1338.jpg
http://i5.photobucket.com/albums/y16...icture1339.jpg
Much better
http://i5.photobucket.com/albums/y16...icture1341.jpg
Enjoy your step by step. My Dad had got a brand new 55 Nomad,I thought was really pretty wagon,I loved the thing as a kid,but 265 leaked n smoked so bad,in Dec of 1955 the dealer put a new 283 in it,that thing sang then,but two more years an dad using it as a work car took a toll on it. Point is I really like 55 wagons.
More great work. Most places I swear just fill those areas with seam sealer.
Thanks for the comments guys.
I've had my Mig welder for quite a while now, and thought I'd downsize a bit. Most of the work I do is sheet metal, and the occasional 1/8 or 3/16 plate. I had looked at the Miller 211's online and on eBay, so I had a price range in mind. I stopped by my local Welding supply and was pleased to find that he had those prices beat by a good bit. So it came home with me..
http://i5.photobucket.com/albums/y16...icture1343.jpg
http://i5.photobucket.com/albums/y16...icture1344.jpg
First order of business was to test it out and do a comparison to the coupon I had done with the old machine. I still had the 11 lb. roll of .023 EZ Grind, so that was used in the new machine. Here are the results...
http://i5.photobucket.com/albums/y16...icture1351.jpg
http://i5.photobucket.com/albums/y16...icture1352.jpg
http://i5.photobucket.com/albums/y16...icture1353.jpg
http://i5.photobucket.com/albums/y16...icture1354.jpg
Both versions, .023 EZ grind and the .035 ER70S-7 in the old machine had very similar results. Good wetting, nice flat weld for minimal build, less grinding, less cleanup.
http://i5.photobucket.com/albums/y16...icture1355.jpg
Back to the front end of the car, the hood had been giving us fits when opening, it was dragging the cowl vent in a few spots...
http://i5.photobucket.com/albums/y16...icture1359.jpg
Removed the hood and altered the angle of the rear flange for better clearance to the cowl vent....
http://i5.photobucket.com/albums/y16...icture1356.jpg
http://i5.photobucket.com/albums/y16...icture1357.jpg
http://i5.photobucket.com/albums/y16...icture1358.jpg
After refitting, the problem persisted, but was not as pronounced. We did notice the center of the hood was sagging a bit. So I jumped inside the engine compartment with the torch and did some contracting of the rear brace to give the center a lift...
http://i5.photobucket.com/albums/y16...icture1365.jpg
http://i5.photobucket.com/albums/y16...icture1366.jpg
Cooling off the hot spots with a damp rag did the trick. Next we worked on getting the hood's rear edge to match up to the cowl. This is something that the driver will stare at continually, so it needs to be a whole lot better than it is now:
http://i5.photobucket.com/albums/y16...icture1361.jpg
http://i5.photobucket.com/albums/y16...icture1362.jpg
http://i5.photobucket.com/albums/y16...icture1363.jpg
Further refinements included this and others:
http://i5.photobucket.com/albums/y16...icture1367.jpg
After taking the hood on and off about a dozen times, this is closer, and the outer edge adjacent to the fender needs to "droop" a bit more. We're running out of time this evening, so we'll try our luck next time with the rocker panel roller to see how well it addresses the edge.
http://i5.photobucket.com/albums/y16...icture1369.jpg
http://i5.photobucket.com/albums/y16...icture1370.jpg
Nice new welder. I've had an automatic 185 for a long time which us a Miller 180 and I loved it. Now my old boss has had it for ever since his snap on one died. I'm still trying to get used to this putsch I got last year.
Boy those gaps are large. I'm sure they'll be gone by next post. :LOL:
Camera perspective. The edge at the fender was opened upwards, the back gap was too tight.
A bit more progress last night on the front end fitment. We've taken the hood off and reinstalled so much that one of the captive nuts came out. Once we fished it out of the hole, it still looked intact, so it will get reinstalled. It was proving difficult to pull back up into the hole, so a bolt was threaded into the nut and the fancy dent puller clamped onto the bolt head. One pull and it was back in place..
http://i5.photobucket.com/albums/y16...icture1371.jpg
http://i5.photobucket.com/albums/y16...icture1372.jpg
It was tacked in place, and to prevent a reoccurrence with the other three, they received tack welds also.
http://i5.photobucket.com/albums/y16...icture1373.jpg
Next, we were working on the hood to cowl gap. We noticed towards the ends of this gap it tended to tighten up. The highly calibrated gap feeler gauge was used...
http://i5.photobucket.com/albums/y16...icture1375.jpg
Here the gap tool had no chance, we need to reform the rear fold on the ends...
http://i5.photobucket.com/albums/y16...icture1376.jpg
http://i5.photobucket.com/albums/y16...icture1377.jpg
http://i5.photobucket.com/albums/y16...icture1378.jpg
The wedge anvil was used, along with a x-large cold chisel that had a radiused edge formed for the more curvaceous profiles (forgot to get a picture), to reform the rear fold inward for this tight area..
http://i5.photobucket.com/albums/y16...icture1356.jpg
http://i5.photobucket.com/albums/y16...icture1380.jpg
http://i5.photobucket.com/albums/y16...icture1383.jpg
Gap looks much more consistent there, a quick look at the passenger side shows it needs reforming as well, but not nearly as much. Getting late, so we'll finish this up next time...
http://i5.photobucket.com/albums/y16...icture1384.jpg
http://i5.photobucket.com/albums/y16...icture1385.jpg
http://i5.photobucket.com/albums/y16...icture1386.jpg
More progress today, part of our hood fitment has been hindered by the hinges. When closing the hood they didn't want to close properly and the back corners of the hood had to be pushed down by hand. Don (acardon) on Trifive website suggested replacing the original shouldered rivets with some bolts and sleeves. We hadn't heard anything promising with reproduction hinges, so what did we have to lose.
First to come up with a hinge spring removal tool...
http://i5.photobucket.com/albums/y16...icture1397.jpg
http://i5.photobucket.com/albums/y16...icture1398.jpg
http://i5.photobucket.com/albums/y16...icture1399.jpg
http://i5.photobucket.com/albums/y16...icture1400.jpg
http://i5.photobucket.com/albums/y16...icture1401.jpg
Now to disassemble the hinge and remove the rivets..
http://i5.photobucket.com/albums/y16...icture1387.jpg
http://i5.photobucket.com/albums/y16...icture1388.jpg
http://i5.photobucket.com/albums/y16...icture1404.jpg
Some 3/8-16 rivnuts were used to make some spacers, and used the lathe to trim them to size, allowing a few thousandths clearance. All of the rivet holes were drilled out for the spacers..
http://i5.photobucket.com/albums/y16...icture1402.jpg
Here are the results, click on the pic for video
http://i5.photobucket.com/albums/y16...icture1394.jpg
Thanks much to Don for the suggestion!
that closes nice