Thread: 302 Stroker??
-
02-05-2013 04:35 PM #196
ROFL... Just call me stubborn! But, I'll persevere!
-
Advertising
- Google Adsense
- REGISTERED USERS DO NOT SEE THIS AD
-
02-05-2013 04:41 PM #197
-
02-05-2013 05:09 PM #198
-
02-06-2013 07:47 AM #199
OK Mike, first I have apologize for the grunge & grime in these pictures, but the car's headed into the shop for some fiberglass work so I didn't take time to detail the engine As you can see, my installation is extremely constrained with the throttle body extension immediately above, and the water neck boss all but surrounding the distributor body. This Mallory Billet distributor was made special for Edelbrock to be as short as possible for vertical clearance, but also small diameter.
Tucked in between the driver's side fuel rail and the water neck:
DSCN6093.JPG
Water neck clearance is all but nothing:
DSCN6091.JPG
Block boss beneath the hold down clamp to bottom of base is ~1.5" (very hard to measure with any accuracy):
DSCN6090.JPG
Tucked under the Throttle Body Extension - Intake has to come off to pull the distributor, but with the cap & rotor pulled there is room to lift it enough to shift the drive gear on the cam gear:
DSCN6095.JPG
The body is very nearly an exact 3.00 inches, not counting the mounting ears for the cap:
DSCN6097.JPG
Hope these help. As I mentioned to you before, I really think you'd be better served by calling Mallory and talking to them about putting something together that may not be "standard". They might have a small diameter body like this one, but with a more "standard" shaft length to get it up above your restrictions. That would be my approach before I started buying and returning units with Summit.Last edited by rspears; 02-06-2013 at 01:31 PM.
Roger
Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.
-
02-06-2013 02:46 PM #200
Thank You for the pics / measures Roger! I' m thinking that the 1.5" from mount to bottom of body would be a killer! I believe my old mallory is 3" off the mount and it hits.
I was browsing MSD last night and I like the looks of one and am waiting for an e-mail reply as we speak. We'll see what happens.
-
02-06-2013 04:05 PM #201
Mike,
I've said several times that the Mallory unit I'm running is a special build, commissioned by Edelbrock to get the lowest overall height they could get with a fully electronic distributor. I did not have any hope that this distributor would work for you, given the constraints. I knew it would be too short. Good luck on the hunt.Roger
Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.
-
02-06-2013 05:42 PM #202
10-4, Roger that... to much stuff trying to occupy what's left of my little brain. I did "chat" with a guy and he said he ran one of these intakes with a stock ford unit "from the day".. so I've been looking at ebay also. Who knows how accurate this guy is.. But it could be a 40 or 50 dollar bet vs. a 300 or 400 dollar gamble.
I found a dizzy at the MSD site that piques my interest, visually I think it might fit, and it has 11 choices of advance curves and it's all done digitally inside the dizzy - under the cap... so I'm window shopping?!?! Shoot me!
-
02-06-2013 05:50 PM #203
dizzy.jpg
Maybe something like this, with a Pertronix kit? Rock Auto, 1965 Ford 289....Roger
Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.
-
02-06-2013 06:02 PM #204
Exactly like that. My local supplier says it'll cost me 60 or 65 for a rebuilt. But if it don't fit.. I own it! What's that pic worth?
-
02-06-2013 06:05 PM #205
Mike, I might still have an old 289 distributor laying around someplace on a shelf---perhaps the early one's were a bit different? Also, some place in one of the dark corners of my feeble brain I seem to remember an offset housing arrangement for a 289???? Not a clue who made it, or even what I might have seen it on. Are the MSD distributors for the crank trigger units a possibility????Yesterday is history, tomorrow is a mystery, Live for Today!
Carroll Shelby
Learning must be difficult for those who already know it all!!!!
-
02-06-2013 06:14 PM #206
If you could scare up an old unit your willing to part with / or / let me test fit with it, that would be great!!!
Offset won't work as there is a piece of the manifold that passes in front and encircles the dizzy.
I started to go down the road of a crank trigger system, but that's a total re-work of more than a few pieces under the dash. It's possible but not desirable.Last edited by 34_40; 02-06-2013 at 06:16 PM.
-
02-06-2013 06:40 PM #207
Mike, here's the link -http://www.rockauto.com/catalog/rafr...&parttype=7108 All but one have a $30 core charge built in, so they're not cheap.Last edited by rspears; 02-06-2013 at 06:42 PM.
Roger
Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.
-
02-06-2013 06:48 PM #208
As always, THANK YOU Roger! 8-)
Maybe Dave will have an old one.....
-
02-06-2013 07:11 PM #209
"It is not much good thinking of a thing unless you think it out." - H.G. Wells
-
02-07-2013 04:46 AM #210
Welcome to CHR. I think that you need to hook up your vacuum advance. At part throttle when cruising you have less air and fuel in each cylinder, and the air-fuel mixture is not as densely packed...
MSD 8360 distributor vacuum advance