Search:
Type: Posts; User: cgw3
Search:
Search took 0.06 seconds.
-
01-21-2016 09:38 AM
- Replies
- 43
- Views
- 5,695
Also considered fuel pump pushrod tapping? Have...
Also considered fuel pump pushrod tapping? Have you guys seen this alot?
-
01-21-2016 09:31 AM
- Replies
- 43
- Views
- 5,695
The previous distributor was also a HEI, but...
The previous distributor was also a HEI, but cap broke and rotor damaged so I wont be able to put that one on to see? But the new one could be damaged and im going to pull and check. I dropped the...
-
01-20-2016 09:07 PM
- Replies
- 43
- Views
- 5,695
Thanks for the help guys. Ill let you know what I...
Thanks for the help guys. Ill let you know what I find.
-
01-20-2016 01:12 PM
- Replies
- 43
- Views
- 5,695
Thanks for your input Jerry. I have no problem...
Thanks for your input Jerry. I have no problem getting my hands dirty, as run a crew, a shop, and manage a 140acre golf course and I am the only one capable of working on 15+ pieces of specialized...
-
01-20-2016 12:51 PM
- Replies
- 43
- Views
- 5,695
I did check pushrods and they are all fine.
I did check pushrods and they are all fine.
-
01-20-2016 08:09 AM
- Replies
- 43
- Views
- 5,695
ok guys,still stuck. Here's an update on what all...
ok guys,still stuck. Here's an update on what all Ive done. Checked starter/flywheel, no issues there. Bought a stethoscope (kind with metal rod) and it amplified the sound but I could not pin it...
-
01-06-2016 08:43 AM
- Replies
- 43
- Views
- 5,695
I have thought about this. with my bellhousing...
I have thought about this. with my bellhousing off, I was able to look at gap between flywheel and starter drive gear, there is a very small gap, but you can see light between it. Is this something...
-
01-06-2016 08:39 AM
- Replies
- 43
- Views
- 5,695
I will try the stethoscope, the engine is loud...
I will try the stethoscope, the engine is loud enough on its own that its really hard to get an idea by sticking you head in the engine compartment.
-
01-06-2016 08:37 AM
- Replies
- 43
- Views
- 5,695
Im not sure that I have a flexplate, unless it is...
Im not sure that I have a flexplate, unless it is mounted on the engine side of the flywheel. Not real familiar with a flexplate, but arent those with auto trans? I have never had the flywheel off,...
-
01-06-2016 08:35 AM
- Replies
- 43
- Views
- 5,695
I will try this, but ive never looked for push...
I will try this, but ive never looked for push rods spinning, didnt know they did, so I have never noticed, thank you/
-
01-06-2016 08:33 AM
- Replies
- 43
- Views
- 5,695
As far as I could tell when I had the jeep...
As far as I could tell when I had the jeep transmission off, it has a bushing. Im not sure if it was previously swapped from bearing to bushing to accomodate t150 trans shaft. I know I would be able...
-
01-05-2016 10:23 AM
- Replies
- 43
- Views
- 5,695
Gen I (1969) SBC 350 NEED HELP, TICKING SOUND
First time post, but view the forum a lot and need a little help from you SBC guys. I have a 1969 SBC 350 ,DH heads, 4bl edlebrock, sitting in my 76 CJ5. Sorry, not your typical hotrod. But I have...
Results 1 to 12 of 12
All true wisdom is found on T-shirts. If at first you don't succeed, redefine success. I don't have a solution, but I do admire the problem. If a thing is worth doing, it would have been...
the Official CHR joke page duel