Search:
Type: Posts; User: CJ 613
-
04-21-2009 02:37 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
Thanks a lot Rum. The info everyone is so willing...
Thanks a lot Rum. The info everyone is so willing to share makes this build much easier and enjoyable. BTW, love the coupe!!!:cool:
-
04-20-2009 07:45 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
ok lets try this again-the reading (AMERICAN) is...
ok lets try this again-the reading (AMERICAN) is .023 below deck height. Tech, is there anyway to run all these specs on your dyno?
-
04-18-2009 07:36 AM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
I brought each piston on each 4 corners of the...
I brought each piston on each 4 corners of the block to TDC. I was "told" that they were in MM (the feelers) and that was the reading. As I said-:o, Ize jes nawt too dang edjamacayted on this heer...
-
04-17-2009 09:02 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
thats what I was looking for-thanks! Now lets...
thats what I was looking for-thanks! Now lets hope I don't screw it up putting it all together.
-
04-17-2009 08:16 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
also did away with the 1.94 s for a set of 2.02...
also did away with the 1.94 s for a set of 2.02 aluminum heads with 64cc runners... and as always...thanks for the input...its always greatly appreciated
-
04-17-2009 08:14 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
tranny is a rebuilt 3speed manual with a lot of...
tranny is a rebuilt 3speed manual with a lot of low end torque and 3:73 rears.
-
04-17-2009 05:24 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
Ok, so here it is: as explained by "tech", I did...
Ok, so here it is: as explained by "tech", I did the measurements with the feeler guage and came up with a strange reading-60 mm from piston tdc to deck height. Now I've been told 350s usually have...
-
04-05-2009 08:08 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
ok, thanks tech. When I get the reading I'll...
ok, thanks tech. When I get the reading I'll repost.
-
04-05-2009 06:13 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
also, here is a pic of the intake on the...
also, here is a pic of the intake on the block-its not too clear but it gives you somewhat of an idea what I'm working with.
-
04-05-2009 05:08 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
how do I measure the piston deck height? And...
how do I measure the piston deck height? And again, any response is extremely appreciated. I know I may be biting off more than I can chew but why not right? I love the knowledge everyone is so...
-
04-05-2009 05:01 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
I'm (trying) to get over 400hp. Not sure if the...
I'm (trying) to get over 400hp. Not sure if the 1.94s will provide that or not.
-
04-05-2009 07:37 AM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
no, not yet. I'm not sure if I want to run the...
no, not yet. I'm not sure if I want to run the 1.94s or not yet. I've been told that I may not get the power I'm looking for with them. I may need to go up to a 2.02.
-
04-04-2009 08:02 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
also, the rockers are 1.6 ratio. The nuts are too...
also, the rockers are 1.6 ratio. The nuts are too small for the studs.
-
04-04-2009 07:55 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
the bottom end was built when I bought it so I...
the bottom end was built when I bought it so I don't know the technical details. Again, any info would be greatly appreciated
-
04-04-2009 02:00 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
Here's another one-this is my first "high...
Here's another one-this is my first "high performance" build. I have a 350 bored .30 over, forged pistons, I believe the cam lift is 550 (its a 5/8 cam), holley strip dominator high rise intake with...
-
04-04-2009 01:57 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
here's a dumb question-how do I know what size...
here's a dumb question-how do I know what size the nuts should be?
-
04-04-2009 12:25 PM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
I unfortunately don't have a camera available.
I unfortunately don't have a camera available.
-
04-04-2009 10:07 AM
Thread: roller rocker help
by CJ 613- Replies
- 30
- Views
- 5,295
roller rocker help
I recently bought a set of what I thought were new comp cams roller rockers (1.6 ratio) for my sbc 350 that I'm building. When I got them home and opened the package I noticed that the nuts had been...
well I decided to do another mod to gain max travel of bars past the intended travel points just for that peace of mind. 1/8 inch is to close so now I'll have 1/2" or better. I cut a 3/16" wall...
New Project