https://i.imgur.com/MHCkZzF.jpg
Engine was just dropped off by the freight company! Just want to finish out my work day and then I'll get started on taking off the EFI components and prep the engine for a carb.
Printable View
https://i.imgur.com/MHCkZzF.jpg
Engine was just dropped off by the freight company! Just want to finish out my work day and then I'll get started on taking off the EFI components and prep the engine for a carb.
I agree with rspears, get a good 220 volt welder, it will have the horsepower to weld chassis and suspension components, and the ability to weld sheet metal with a little finesse.
The shop foreman decided he needed to inspect the delivery before any work could start :)
https://i.imgur.com/wRhqPhj.jpg
Can anyone tell me what this sheared off piece is? I know my donor car was in a front-end collision so I'm wondering if this is related
https://i.imgur.com/FG3c34n.jpg
https://i.imgur.com/vMDvsvA.jpg
Spark plugs from both sides look OK, I'm encouraged by this
https://i.imgur.com/IZCgb7l.jpg
https://i.imgur.com/8WbzFAM.jpg
I have one of these being delivered to my tomorrow. No one is going to confuse Husky for a top tool company but for my space needs, I think this will work just fine.
https://i.imgur.com/3hljSkw.jpg
That broken part appears to be the serpentine belt tensioner. If you are converting to a v-belt front drive, you won't need it.
If I had an engine with plugs that nice, no way I would rebuild it! Unless something is damaged on the long block assembly from the wreck, it looks like you got a good one.
For your application, most of the bolt-on external parts will go in the trash, including the distributor and water pump.
Yes, I'm going to follow the advice of leaving the engine alone for now. My current plan is to (1) put my chassis on order and (2) convert the engine to carb. Once that's done I'll fit the engine to the chassis so I can check fit, etc. and continue the build from there.
Is your cloths dryer near your garage? If so is it 220V? If it is, this is what I did, built myself a heavy duty extension cord to run my air compressor and welder before I upgraded my service. It's not the best, but I gets you going on what you want to do. I still have the extension cord, it's all set up to extend my welder power so I can use it outside of my shop.
I agree, get a length of No8-3 conductor multi-strand wire with good outdoor insulation from your electrical supply house, and the male/female connectors that you need. I think I would consider extending the circuit from your dryer plug to a new outlet on the common wall in the garage rather than having to move the dryer away from the wall any time I wanted to weld, then reversing when you need the dryer. I think my welder extension is 50' to let me move the welder around the barn, or outside if needed. If you don't want to make one Google "Welder Extension Cord" for lots of options, but pay attention to the end connectors.
The broken part you pictured appears to be the belt tensioner.
And you will need the transmission in place when you want to check fitment of motor, it's a package deal, cannot really do one without the other, plus you will need to tell the chassis builder what the package going in will be. Along with the tranny you'll need the starter locator plate. It goes between the motor block and trans bell housing. it indexes ( aligns) the starter motor the correct distance from the crankshaft centerline. The 2 starter bolts are special but common hardware can usually work. And don't worry about using Loctite on anything for now. You only need to do the assembly at this point. It's called "mocking up".. you actually "build / assemble" the car, once it's all together, then you blow it all apart for paint and then re-assemble paying attention then to the fit and finish fine tuning.
As long as everybody is making suggestions, I'll throw my 2 cents in. :LOL:
As it might be a while before you are ready to install the engine and transmission another investment you might consider is an engine/run stand. It will make the engine more stable when removing or installing parts and if you get one with a radiator you can actually fire the engine, check oil pressure, set timing and adjust the carburetor prior to either tear-down (if needed) or installation. It will also allow you to roll the engine around out of the way when needed.
You will need to make sure you get one long enough to accommodate the bellhousing as on the Fords the starter connects there rather than on the engine block. If you go with a T5 getting the bellhousing won't be wasted.
Another option rather than buying one is to grab some steel and build your own.......might be a good practice project for your welding.
This is one I put together a while back for an engine I knew would be sitting a while before it went into a vehicle.
https://www.youtube.com/watch?v=K2a8j3GsYNY
From personal experience I've found being able to fire the engine for a project up from time to time can be a good motivator to keep the project going.
.
.
Forgot to mention, the only limitation you will have with the dryer plug is you will be limited to 35 amps, but hey, better than nothing and it will do pretty much anything a 220V wire feed can pull. Plus, you can also run an air compressor, everyone needs an air compressor.