Wow! Just went thru this thread from the start. Your metal working skills are a thing of beauty. Thanks for taking the time to photograph your process and show your home made jigs and tools. Definately will be watching this to the end. Steve.
Printable View
Wow! Just went thru this thread from the start. Your metal working skills are a thing of beauty. Thanks for taking the time to photograph your process and show your home made jigs and tools. Definately will be watching this to the end. Steve.
Thanks!
With the epoxy well cured, holes were drilled for plug welds....
http://i5.photobucket.com/albums/y16...cture339-1.jpg
Then used the modified plug weld bit for cleaning out the adjacent panel...
http://i5.photobucket.com/albums/y16...cture340-1.jpg
http://i5.photobucket.com/albums/y16...cture342-1.jpg
http://i5.photobucket.com/albums/y16...cture343-1.jpg
Cleaned spots for the plug welds...
http://i5.photobucket.com/albums/y16...cture344-1.jpg
http://i5.photobucket.com/albums/y16...cture345-1.jpg
http://i5.photobucket.com/albums/y16...cture346-1.jpg
http://i5.photobucket.com/albums/y16...cture348-1.jpg
I had some questions about how well the epoxy held up to heat from welding. The epoxy next to the weld above, where it turned brown from the heat, was allowed to cool off, then attempted to scrape the paint with my thumbnail. I thought it may scrape some off, but it held tight, not so much as a scratch.
Then I got on a roll and forgot pictures, but here's the patch all welded in....
http://i5.photobucket.com/albums/y16...cture349-1.jpg
Next, drilled the holes in the lower window opening....
http://i5.photobucket.com/albums/y16...cture350-1.jpg
.....and got the holes placed for the nut plate and it's plug welds...
http://i5.photobucket.com/albums/y16...cture351-1.jpg
http://i5.photobucket.com/albums/y16...cture352-1.jpg
http://i5.photobucket.com/albums/y16...cture353-1.jpg
Hopefully tomorrow we can get some profile blocks cut out to fold over the ends of the outer piece...
Laying out the ends for trimming.....
http://i5.photobucket.com/albums/y16...cture354-1.jpg
http://i5.photobucket.com/albums/y16...cture355-1.jpg
Here's the piece we'll use to cut out the profile blocks, 3/4 thick steel
http://i5.photobucket.com/albums/y16...cture357-1.jpg
As I am fresh out of good band saw blades, these were used....
http://i5.photobucket.com/albums/y16...cture358-1.jpg
The lower piece was tapered at the bottom as the bottom of the lift gate tapers in below the bead detail..
http://i5.photobucket.com/albums/y16...cture360-1.jpg
.....like so.....
http://i5.photobucket.com/albums/y16...cture361-1.jpg
Not perfect, but should work just the same...
http://i5.photobucket.com/albums/y16...cture363-1.jpg
Clamped in the vise.....
http://i5.photobucket.com/albums/y16...cture365-1.jpg
Then some heat is applied, and hammered the high spots..
http://i5.photobucket.com/albums/y16...cture366-1.jpg
http://i5.photobucket.com/albums/y16...cture367-1.jpg
http://i5.photobucket.com/albums/y16...cture368-1.jpg
Fitted.....
http://i5.photobucket.com/albums/y16...cture369-1.jpg
http://i5.photobucket.com/albums/y16...cture370-1.jpg
and the other end......
http://i5.photobucket.com/albums/y16...cture373-1.jpg
http://i5.photobucket.com/albums/y16...cture374-1.jpg
http://i5.photobucket.com/albums/y16...cture375-1.jpg
http://i5.photobucket.com/albums/y16...cture376-1.jpg
Hope to test fit everything tomorrow before all the parts get media blasted..
Nice work. Some times making the jigs (dies) is more work than using them. Again nice work
Very true. About twice as much time in making the dies as using them.
Things don't always work the way you planned. Before the ends were folded, the bottom piece could never be test fit into the opening. Now with the ends folded, it was slipped over the bottom of the lift gate and it bolted into the opening. With the upper bead detail aligned, the lower was considerably off kilter. Slightly off on the contour, I guess.
http://i5.photobucket.com/albums/y16...cture379-1.jpg
http://i5.photobucket.com/albums/y16...cture380-1.jpg
The patch piece was marked off on both ends to bring the lower bead detail up into the car for better alignment...
http://i5.photobucket.com/albums/y16...cture381-1.jpg
Here's the driver's side after cutting and welding, shows a much better alignment. Good weld penetration on the inside, the seam at the end will be finished after folding onto the lift gate..
http://i5.photobucket.com/albums/y16...cture383-1.jpg
http://i5.photobucket.com/albums/y16...cture384-1.jpg
http://i5.photobucket.com/albums/y16...cture385-1.jpg
We may be able to save this yet..
Wow, I hope guys with your talent don't look at my sheet metal work. :LOL: What kind of torch head is that? That is really cool how you were able to get those wrinkles out of the material after folding it up there.
The torch is a Henrob, but I believe it goes by the name of Cobra torch now. It has about 6 different tips for the torch head, so you can really fine tune the flame size to the job.
Cobra is correct on the torch. They're sold almost exclusively at trade shows now, with strong focus on big name auto gatherings. Bought mine at the last Good Guys in KC a couple of years ago, and need to spend a few weeks burning gas and learning how to use it. Link - Cobra Torches | Oxy / Acetylene Welding and Cutting System
That cobra deluxe kit is .. wow. Does it require new regulators, or can I use my old ones? I'll bet It's a bit pricey.
Pretty neat setup, never played with a torch before, but what you do with it is very impressive. I'm definately understanding the term Shadetree for my skills will metal! :)
just had a good look at this one. it aint gona get much bettern this.
Sorry for my short hiatus from the shop, after 226K miles my trusty 16 year old truck has been giving me fits with transmission issues. After spending about 3 weeks on and off looking for good used trucks, the year end deals and rebates made a brand new one only slightly higher in price than a three year old model. So.....
Out with the old...
http://i5.photobucket.com/albums/y16...Picture366.jpg
In with the new....
http://i5.photobucket.com/albums/y16...Picture401.jpg
And with the truck shopping headaches behind us, we can get back in the shop ...
Worked on the other end of the lower patch today, to fix the mis-alignment of the beltline trim...
http://i5.photobucket.com/albums/y16...cture380-1.jpg
Made a relief cut....
http://i5.photobucket.com/albums/y16...cture403-1.jpg
http://i5.photobucket.com/albums/y16...cture404-1.jpg
Rear view shows full weld penetration....
http://i5.photobucket.com/albums/y16...cture406-1.jpg
Welds were planished, then ground to just above panel surface, and next weld overlapped, and repeat. The overlapping helps to eliminate any missed welds/pin holes.
http://i5.photobucket.com/albums/y16...cture408-1.jpg
http://i5.photobucket.com/albums/y16...cture409-1.jpg
http://i5.photobucket.com/albums/y16...cture410-1.jpg
http://i5.photobucket.com/albums/y16...cture411-1.jpg
http://i5.photobucket.com/albums/y16...cture412-1.jpg
http://i5.photobucket.com/albums/y16...cture413-1.jpg
http://i5.photobucket.com/albums/y16...cture414-1.jpg
http://i5.photobucket.com/albums/y16...cture415-1.jpg
http://i5.photobucket.com/albums/y16...cture416-1.jpg
http://i5.photobucket.com/albums/y16...cture417-1.jpg
All done and cleaned up....
http://i5.photobucket.com/albums/y16...cture418-1.jpg
http://i5.photobucket.com/albums/y16...cture419-1.jpg
......for a much better fit..
http://i5.photobucket.com/albums/y16...cture420-1.jpg
Then media blasted the inside in preparation for some epoxy primer...
http://i5.photobucket.com/albums/y16...Picture425.jpg
.....and did some adjustment of the tailgate fitment.
http://i5.photobucket.com/albums/y16...Picture422.jpg
http://i5.photobucket.com/albums/y16...Picture423.jpg
Sometimes you just need to back up and punt.
Even though I have been working on this car far too long, with travel for the day job and two other resto's having been quite an interruption..... you get to where you finally see light at the end of the tunnel, and just come to grips with something that needs to come back out....
When I originally did this roof repair, I did not have the Lennox nibbler or English wheel or many of the tools I now have, and the patch panel you see below.....
http://i5.photobucket.com/albums/y16...n/HPIM5655.jpg
....was fabricated using incremental bends in an apron brake. Given the creases you see due to the fabrication method, I likely made this shorter than I should have in an attempt to limit the creases, and the result was the horizontal weld was not up high enough to be readily accessible for planishing. After making these patch panels for a second roof repair......
http://i5.photobucket.com/albums/y16...Picture129.jpg
.....it was more apparent that the first attempt was not the best, and if I wasn't happy with it before, this new panel really made the old one grab my attention...each time I've walked by.
http://i5.photobucket.com/albums/y16...Picture437.jpg
http://i5.photobucket.com/albums/y16...Picture438.jpg
http://i5.photobucket.com/albums/y16...Picture439.jpg
Well a person with spare patches lying around can only take so much, so tonight I checked the fit of one of the spare patch panels.... Looking at the front, the panel needed just a bit more crown....
http://i5.photobucket.com/albums/y16...Picture441.jpg
And the rear needed just a bit less....
http://i5.photobucket.com/albums/y16...Picture446.jpg
So with the Go Kart slick mounted up and ready to go, a 6" then 3.75" radius lower anvil added the crown needed for the front and a 24" radius flattened out the rear for a much better fit.
http://i5.photobucket.com/albums/y16...Picture443.jpg
http://i5.photobucket.com/albums/y16...Picture444.jpg
http://i5.photobucket.com/albums/y16...Picture447.jpg
http://i5.photobucket.com/albums/y16...Picture448.jpg
http://i5.photobucket.com/albums/y16...Picture450.jpg
http://i5.photobucket.com/albums/y16...Picture451.jpg
http://i5.photobucket.com/albums/y16...Picture452.jpg
These panels are about 4" high and put the weld up above the roof boxing structure, so planishing will be more accessible to give us a better job. I'll get the patch all primed on the inside and let it cure. Then cut out the old patch and get this new one welded in.. More to come..
Was in the middle of media blasting the innards of the lift gate and noticed the threads for these nut plates didn't look too "full" A test with a 10-24 screw showed that some of the holes were so bad that they had a "slip" fit.
http://i5.photobucket.com/albums/y16...Picture453.jpg
These hold the rubber bumpers on the bottom inside edge of the lift gate. The spot welds are drilled to release the nut plate..
http://i5.photobucket.com/albums/y16...Picture454.jpg
http://i5.photobucket.com/albums/y16...Picture455.jpg
The new ones are cut out of some 10ga steel, holes drilled and tapped.
http://i5.photobucket.com/albums/y16...Picture456.jpg
yeah, these threads look much better....
http://i5.photobucket.com/albums/y16...Picture457.jpg
Where I normally use a couple screws to hold nut plates in place for welding, with the close proximity of the plug weld hole the screw heads would obscure some of the hole, and we would undoubtedly be welding in the screw heads for difficult removal. For this case, we'll use some brass tubing as a spacer. Since the tubing I picked up passes though the screw holes, a sacrificial lock washer is used for it's minimal diameter.
http://i5.photobucket.com/albums/y16...Picture459.jpg
http://i5.photobucket.com/albums/y16...Picture460.jpg
A dab of anti sieze is placed on the screw threads to insure they don't get welded in place from arcing across the threads.. Plug welded, and screws removed.
http://i5.photobucket.com/albums/y16...Picture461.jpg
Lock washers removed and plug welds ground flush....
http://i5.photobucket.com/albums/y16...Picture463.jpg
http://i5.photobucket.com/albums/y16...Picture468.jpg
And now we can finish up the media blasting....
http://i5.photobucket.com/albums/y16...Picture469.jpg
http://i5.photobucket.com/albums/y16...Picture470.jpg