Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree2Likes

Thread: 350 backfires through carb
          
   
   

Reply To Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 15 of 31
  1. #1
    sd455 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2009
    Location
    lorain
    Car Year, Make, Model: 1978 Trans Am
    Posts
    4

    350 backfires through carb

     



    Hope somebody can help!Just rebuilt a 1972 chevy 350 with a new
    crankshaft,edelbrock torquer plus cam,torker manifold,holley carb,
    summit 1.6 ratio rocker arms,HEI distributor.This motor is in a 1979
    nova and ran well before.Now when trying to start it backfires
    through the carb something terrible.Have tried readjusting the
    valves,and thetiming looks good for starting(checked with timing light).
    Any ideas?I'm dying over here.

  2. #2
    nitrowarrior's Avatar
    nitrowarrior is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2007
    Location
    Mesa
    Posts
    1,385

    First, go back to basics and recheck for proper firing order, Again, and again until you're sick of doing it. Second, check for enough fuel going into the beast. A lean condition will cause this always.
    Those are the two biggest proponents of carb backfiring.
    What if the "Hokey Pokey" is what it's really all about?

  3. #3
    pat mccarthy's Avatar
    pat mccarthy is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Apr 2005
    Location
    bay city
    Posts
    10,546

    you could be wipping off a cam lobe
    Irish Diplomacy ..the ability to tell someone to go to Hell ,,So that they will look forward to to the trip

  4. #4
    R Pope is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    Eston
    Posts
    2,270

    Firing order first, intake valve riding open second, vacuum leak third thing to check. My money is on crossed wires.
    That's assuming the cam is timed right.

  5. #5
    sd455 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2009
    Location
    lorain
    Car Year, Make, Model: 1978 Trans Am
    Posts
    4

    I've checked the firing order countless times and adjusted the valves according to
    edelbrocks instructions.I've rebuilt several motors(fords,chevys,and pontiacs)and
    they've always started right up.I will check for vacuum leaks and check fuel
    pressure as soon as I can.Thanks for the tips.

  6. #6
    pat mccarthy's Avatar
    pat mccarthy is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Apr 2005
    Location
    bay city
    Posts
    10,546

    re check 5 and 7 wire
    Irish Diplomacy ..the ability to tell someone to go to Hell ,,So that they will look forward to to the trip

  7. #7
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    It sounds like a timing issue. I know that you’ve probably looked at this until you’re blue in the face. The sketch below represents what you should be looking at from the top. This is real basic – but unless you’re building a race motor, the following will get you where you need to be.

    Start all over with number one at TDC. Make sure that when the piston is at TDC (as indicated by the timing marks on the harmonic damper) that both valves are closed on number one. If not, your cam is out of time and there may be some big problems. You didn’t mention any bad “crunching noises” so we trust the cam is in time with the crank.

    Remove the distributor cap and the spark plug wires. The distributor rotor should be in the approximate position shown. If not, you’re off and need to take the distributor out and re-insert so the rotor matches the sketch. Snug the distributor hold-down bolt but not so tight that the base of the distributor will not turn by hand. Reinstall the wires. I always follow the firing order, i.e., 1-8-4-3-6-5-7-2. This might sound basic – but do it.

    Now install your timing light on number one and start the engine – it will start. The little things are really the big things

    Good Luck,
    Glenn
    Attached Images
    "Where the people fear the government you have tyranny. Where the government fears the people you have liberty." John Basil Barnhil

  8. #8
    sd455 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2009
    Location
    lorain
    Car Year, Make, Model: 1978 Trans Am
    Posts
    4

    Hi peoples,I'm back.I've checked for vacuum leaks and have plenty of gas,
    even replaced the fuel pump.I took the valve covers off and while cranking
    looked for any sticking valves,but there were none.When trying to start
    this thing it will backfire and start the inside of the carb on fire.Has anyone ever heard of a camshaft being ground wrong?I'm at my wits end here
    and have never seen anything like this.Any ideas?

  9. #9
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,334

    I believe your 180* out.
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  10. #10
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    Remove #1 spark plug and rotate the crank clockwise until you feel pressure building against your thumb while holding your thumb, or your buddy's thumb, over the spark plug hole. Watch the harmonic damper ring and bring the TDC mark on the inertia ring up to match the timing tab on the front cover. Now you are at TDC firing #1.

    Remove the distributor cap and verify the rotor is pointing at about 5:30 O'Clock as you stand in front of the motor. (more or less pointing at #1 cylinder). If not, remove the distributor and re-stab it, positioning the vacuum advance can so that you will have room at the manifold runners to turn the distributor housing clockwise and/or counter-clockwise to change initial timing later. Plug #1 plug wire in at the 5:30 position, matching up with the rotor. Going clockwise around the cap, plug in the remainder of wires in firing order....1-8-4-3-6-5-7-2.

    On the front of the crank pulley, make a mark or attach a little piece of masking tape at 12:00 O'Clock, 3:00 O'Clock, 6:00 O'Clock and 9:00 O'Clock.

    Back off both rocker nuts so that you have a little play. Grasping the pushrod with your thumb and forefinger, jiggle it up and down while you hold the rocker arm tip down against the valve stem tip. Adjust the nut until all jiggle room is taken up and you have zero lash. Give the nut an additional 1/2 to 3/4 of a turn. Do both the intake and exhaust on #1 while you are there.

    Rotate the crank clockwise 1/4 turn (90 degrees) so that your 9:00 O'Clock piece of tape is now at 12:00 O'Clock. Back off the intake and exhaust nuts on #8 cylinder and adjust both valves the same as you did on #1.

    Rotate the crank another 1/4 turn so that the 6:00 O'Clock piece of tape is now at 12:00 O'Clock and adjust both valves on #4 cylinder.

    Keep rotating the crank 1/4 turn at a time and continue through the firing order until you have all valves adjusted. 1-8-4-3-6-5-7-2. Driver's side front to rear, 1-3-5-7. Passenger side front to rear 2-4-6-8.

    It takes a lot of experience to get the valves adjusted correctly if you are using the "spin the pushrod" method of removing lash at the rockers. I would guess that 99% of the fellows doing it this way will get the valves too tight. This "jiggle up and down" method was passed on to me by Denny W and is bulletproof.

  11. #11
    hotrodstude is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2009
    Location
    pendergrass
    Car Year, Make, Model: 2006,ford,f-150,v-6,5-speed manual
    Posts
    245

    how old are the sparkplug wires? rotor and cap? do you have points? does it idle at 2500rpm? more info please?

  12. #12
    Jetstang's Avatar
    Jetstang is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2009
    Location
    niceville
    Car Year, Make, Model: 90 454 SS truck and 2 pontiacs and a vet
    Posts
    52

    I think he's 180 out also, great info from tech and all.
    It doesn't matter where you put the #1 wire as long as the dist cap matches, wires may be short in some cases.
    Also make sure the firing order is in the correct direction with the rotation of the dist.
    Good luck.

  13. #13
    hotrodstude is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2009
    Location
    pendergrass
    Car Year, Make, Model: 2006,ford,f-150,v-6,5-speed manual
    Posts
    245

    are you using a COMP.CAM? the reason is ask is because i got a bad cam from them for my 455 t/a when they first came out was the first and last time i used there products.long story

  14. #14
    haveNOclue is offline Registered User Visit my Photo Gallery
    Join Date
    Aug 2009
    Location
    Cincinnati
    Posts
    1

    Quote Originally Posted by sd455 View Post
    Hi peoples,I'm back.I've checked for vacuum leaks and have plenty of gas,
    even replaced the fuel pump.I took the valve covers off and while cranking
    looked for any sticking valves,but there were none.When trying to start
    this thing it will backfire and start the inside of the carb on fire.Has anyone ever heard of a camshaft being ground wrong?I'm at my wits end here
    and have never seen anything like this.Any ideas?
    I dont know a whole lot about engines, BUT I had this same exact thing happen to my chevy 355 engine. I found out it was the + battery wire to the distributor.. It had a break in the wire and only a few strands holding it together... maybe something to check out...

  15. #15
    37 Caddy's Avatar
    37 Caddy is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2005
    Location
    Phoenix
    Car Year, Make, Model: 1937 Caddy LaSalle, 66 Lone Star Cobra
    Posts
    227

    This may sound stupid, but is the fuel line connected to the right port on the carb? I learned this the hard way. When I changed a carb once the mechanic put the fuel line on a vaccuum port because that is where the fuel line was originally. So then, everytime I would try to start it, it would catch on fire.

    If you are all done laughing at me, it was my first "hot rod" and I dutifully learn from my mistakes.

Reply To Thread
Page 1 of 3 1 2 3 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink