Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: 302 cyl head print (needed!)
          
   
   

Reply To Thread
Page 2 of 4 FirstFirst 1 2 3 4 LastLast
Results 16 to 30 of 57
  1. #16
    Henderlong is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2010
    Location
    South Lyon
    Posts
    17

    Sorry about the mis communication. The only thing im confused on is the bolt hole center location compared to the port hole center. These must be exact because if they are off then, bolts, ports, and everything could be not lined up correctly.
    I am having a hard time finding this.

  2. #17
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    I think that the reason that you are having trouble finding the tapped hole location relative to the port is that it is not an exact dimension.....the ports are cast and the header bolt hole locations are machined when the head is clamped against some reference surface...usually pads at the ends or head bolt surfaces that were machined in the first operation. The casting cores are not in a terribly precise location....so things vary among heads.

    I think the suggestion of taking your heads and doning a real measurement on them is the best if you want precision......OR you could make your plates and hand fit them to your heads.

    mike in tucson

  3. #18
    Henderlong is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2010
    Location
    South Lyon
    Posts
    17

    if they are made in the prosses that you describe, than any aftermarket header that you buy will not fit on any head, because it is not "in a terribly precise location".

    The factories MUST have some talerance for the casting.

    Well my plan is to make the flange, then make tools (inside and outside die/madrel) to flare the pipe to a more oval shape. and directly match the port size. (or bigger).
    The pipe will then slide into the flang then be tig welded on the inside, (head side).
    Any comments?

  4. #19
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    First of all, if you take a stock factory exhaust manifold and match it to the head, you will be shocked at how far it can be off......1/8" is not uncommon. Some exhausts are made
    bigger all around the port on purpose so there is a drop off going into the exhaust.

    Headers are'nt much better; I've had to move the header bolt holes by almost 1/4" on some header models.....if I didnt, the flow would be terrible at the junction.

    The best way to start the process is to find or make a gasket that matches your head....check both heads to see if they are the same. Take that new gasket/template and put it on your exhaust and see where you fall......then, make your new flanges from your template so they fit.....

    What you are describing as to your fabrication of headers is essentially what the header guys do.

  5. #20
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    11,124

    From my discussions with the custom header guys and my experience on one set of headers, the flanges you buy have the ports sized to match the OD of your prescribed primary tube. For a 302 the "normal" is 1 5/8" primaries and the tubing is a controlled OD which gives you a circumfurence of 5.11" so the port perimeter will be about 5.15" or so. When you form your tube to fit and tap it into place you'll get nearly a zero gap fit. Header guys I talked to said to weld on the outside, leaving the machined surface of the header flange unmolested, but to never weld both sides of the flange.

    Sounds like you already know exactly what you want to do, and that you either own or have access to some pretty sophisticated equipment. Not many people can afford to spend time making things like custom header flanges and make it pay off so you are in an enviable position. Good luck with your header build. I'd love to see pictures of your process as you move forward.
    Last edited by rspears; 11-10-2010 at 01:00 PM.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  6. #21
    sfort's Avatar
    sfort is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2009
    Location
    Allen
    Car Year, Make, Model: 46 Chevy Truck
    Posts
    528

    I think he is talking about the relation ship of the mounting bolts to the 1.9" dim.. They are not centered to the port. The ball pein and poster board is a good idea. Henderlong are you going to program a digital pattern into a water jet or laser?

  7. #22
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    11,124

    Quote Originally Posted by sfort View Post
    I think he is talking about the relation ship of the mounting bolts to the 1.9" dim.. They are not centered to the port. The ball pein and poster board is a good idea. Henderlong are you going to program a digital pattern into a water jet or laser?
    Yeah, sfort I agree. I would put a bolt in the front & rear mounting holes on the head, run a good straight edge across the top & bottom of the bolt measuring to the respective port edges. Those measurements plus the bolt OD, all measured with a dial caliper will give him the offset within 0.001" or closer. I'd rather have the measurements from my head than the dimension from somebody's drawing.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  8. #23
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Quote Originally Posted by Henderlong View Post
    if they are made in the prosses that you describe, than any aftermarket header that you buy will not fit on any head, because it is not "in a terribly precise location".

    The factories MUST have some talerance for the casting.

    Well my plan is to make the flange, then make tools (inside and outside die/madrel) to flare the pipe to a more oval shape. and directly match the port size. (or bigger).
    The pipe will then slide into the flang then be tig welded on the inside, (head side).
    Any comments?
    From someone who's fabricated many sets of SBF headers, I have to say I think you're making the process way too difficult.....

    As others mentioned, use the gasket that most closely matches your exhaust port opening, then grind the od of the flange to match... I usually by a header kit, with flanges, tubes, and collectors from Speedway. Once I get the flanges to match the ports, it's a simple matter of dingin' the round tubes to an oval shape on the end with a body hammer and some solid round stock with the correct radius held in the vice.

    Unless you're tuning for one or two horse on the dyno, don't really see where anything more exotic would be required.....and if you are looking for the absolute best horsepower, then you've got the wrong set of heads anyway...JMO
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

  9. #24
    Henderlong is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2010
    Location
    South Lyon
    Posts
    17

    Hha, ya i know these heads are not the greatest....
    I used a cmm machine to answer my own question.
    If you were to draw a line down the center of the bolts, the port ends 18.5608mm in one direction, and 12.9901mm in the other. So i took a persentage of that and apllied it to a 1.8inch (h) x 1.32inch (w) port on the flange
    I will post a picture once i finish the design

    idk if i want to use a ball pean hammer to shape the tube. I sorta want to flare it out useing a press and some custom tools. This would be better for production if i wanted.

    I have axcess to a 3 axis cnc machine at school. All i have to do is build it on CAD and convert it to a txt doc. Then i take it over to the cnc.
    However i first want to mill it out of wood, to ensure that it fits correctly. I will of course use a wood cnc mill for this, not a metal one.
    Just give me a few hours to make a mock up design.
    STAY TUNED
    Last edited by Henderlong; 11-10-2010 at 09:13 PM.

  10. #25
    Henderlong is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2010
    Location
    South Lyon
    Posts
    17

    K heres my mock up. Dimentions are exact. Im not sure how i want the outside too look yet?
    Like i said before. the pipe will be flared so that the outside diameter fits snugly inside the flange.
    Attached Files

  11. #26
    vara4's Avatar
    vara4 is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2003
    Location
    Pahrump
    Car Year, Make, Model: 1947 International Pick Up
    Posts
    3,187

    I am not sure what kind of machine it is, but there is a place in Tampa where you can take metal up to about a inch thick and they can cut that kind of stuff out for you.
    The only reason I know about it is there is a fuel tanker repair shop in front of it and the guys in there were telling me about it on day. Not sure if it's a laser type machine or some type of dye cutting machine they use though. But it is good to know it is there, if ever needed though.
    Kurt

  12. #27
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    11,124

    Quote Originally Posted by Henderlong View Post
    K heres my mock up. Dimentions are exact. Im not sure how i want the outside too look yet?
    Like i said before. the pipe will be flared so that the outside diameter fits snugly inside the flange.
    The bottom edge is only important for plug clearance, and then mainly for angled plugs which can be a pain with some headers. If you're making them out of wood first you can check plug clearance and tweak if necessary, right? Telling us that you're a student with access to the school tools and the blessings of your professors/shop manager brings some sanity to this thread, at least for me. It's a great project given your situation

    PS - on the welding I looked at Don's thread http://www.clubhotrod.com/forums/sho...threadid=46852 and Hedman does theirs the other way, letting tubes protrude on the head side, welding a solid bead and them machining that flat. You would at least need a belt sander large enough to do all four ports at once, if not a mill to keep it flat I would think. That keeps the front side cleaner and gives a little more room for header bolts on the flange.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  13. #28
    Henderlong is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2010
    Location
    South Lyon
    Posts
    17

    Yes, i def like the idea of welding on the inside (head side), then machining it down. Im not sure if i want to write a program to machine the welds down, or just put it in a vise, and use the bridgeport?

    Yes, wood will be used to double check everything. plug clearence is a must, but shouldnt be a problem.

    And im pretty sure i dont need to go all the way to tampa to cut this thing out. ha i live in michigan. allitle far? I dont need a lazer. a simple 3 axis machine should work dandy.

    Ha idk about sanity... i'm pretty much doing this project on my own. I'm just using their tools ha. i have never done anything this big before. however im switching on and off with this and rebuilding a c4 trans that just blew out in my truck.

    I'l try to finish up some tools to flare the pipe tonight, and u guys can tell me your thoughts on that.
    Last edited by Henderlong; 11-11-2010 at 07:15 AM.

  14. #29
    IC2
    IC2 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    UPSTATE New York
    Posts
    4,336

    Quote Originally Posted by Henderlong View Post
    Yes, i def like the idea of welding on the inside (head side), then machining it down. Im not sure if i want to write a program to machine the welds down, or just put it in a vise, and use the bridgeport?

    Yes, wood will be used to double check everything. plug clearence is a must, but shouldnt be a problem.

    And im pretty sure i dont need to go all the way to tampa to cut this thing out. ha i live in michigan. allitle far? I dont need a lazer. a simple 3 axis machine should work dandy.

    Ha idk about sanity... i'm pretty much doing this project on my own. I'm just using their tools ha. i have never done anything this big before. however im switching on and off with this and rebuilding a c4 trans that just blew out in my truck.

    I'l try to finish up some tools to flare the pipe tonight, and u guys can tell me your thoughts on that.

    You can rebuild that C4 in your spare time, they are about as simple as any to do - but a word to the wise, make sure you use HiPo parts to extend its life
    Dave W
    I am now gone from this forum for now - finally have pulled the plug

  15. #30
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    11,124

    So Henderlong, are you in school now in Michigan or do you just have access to a machine shop? Just curious...
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

Reply To Thread
Page 2 of 4 FirstFirst 1 2 3 4 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink