Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree14Likes
  • 1 Post By 34_40
  • 3 Post By 36 sedan
  • 6 Post By 36 sedan
  • 3 Post By 34_40

Thread: 383 Stroker Carb Issues
          
   
   

Reply To Thread
Results 1 to 11 of 11
  1. #1
    zaneyboi is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2021
    Location
    Gadsden
    Posts
    16

    383 Stroker Carb Issues

     



    Hey all, new to this forum. I have a trans am with a 383 stroker with a Barry Grant 750 Carb. The issue I have is whenever I crank the car the AFR starts out about 14:7 which is perfect. But within less than a minute it will go to around 12:1 AFR, then about another minute or two after it will go straight to dead lean. I don't understand why it is doing that. The car idled just fined before I let it sit for a couple months now all of sudden it doesn't run right. Any help?? I've messed with adjusting the screws and I've tried changing the primary jets in the metering block but it just makes it run even more rich the ultimately goes dead lean within the minute. I am STUCK!!

  2. #2
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,989

    Welcome to the forum, Zaneyboi. Just to be sure we're talking the same on ratios, an AFR of 14.7 to 1 air to fuel is the stoichiometric ratio for maximum efficiency - a nice target number for highway cruise, but likely never seen at idle or acceleration. As we go "rich" the amount of air to fuel drops - the 14.7 goes lower. As we go "lean" we're pushing more air for each volume of fuel, and the 14.7 goes higher. When you say that in less than a minute your AFR goes to around 12:1 you're getting richer than you were on initial start which doesn't make sense. Even in Alabama on a cold start your choke is set, so I'd expect an AFR of more like 10.5 or 11 to 1, then after a minute or less the choke plate is opening and the AFR would bump to maybe 12 to 1.

    On your idle stop you need to adjust your idle air screws to maximum vacuum, right? The old school approach was to close one until RPM dropped, open until RPM dropped, and set halfway between the two spots but vacuum is better. From you saying it goes "...straight dead lean" I'm wondering if maybe you went the wrong way on tweaking the primary jets?

    I've never messed with a Street Demon carb, so I apologize if I'm leading you down a rabbit hole. Maybe one of the guys will jump in and help out a bit, but glad to have you here!
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  3. #3
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Mr Spears, you're explaining it right. first, toss out that number right after cranking. it's not reliable. the readings have to be at operating temperature and after a run. sitting in your driveway at an idle and "evaluating" isn't the right way to look at this. You need to take a test drive of varied rpms and then return to where you started and then note what you observed during the different rpm ranges. You say it was good until it sat for months.. have you checked for vacuum leaks? Or perhaps the pvc valve isn't "right" somehow? Is the air cleaner clear /clean and in the right place? Could a critter maybe have "moved in"??
    glennsexton likes this.

  4. #4
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    I'm curious yo know how you are measuring your AFR.

    Welcome to the site.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

  5. #5
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    Your Idle Mixture passages are clogged from sitting. Remove the mixture screws and squirt cleaner through the holes and follow with compressed air or other source of high volume air (leaf blower), do this a couple of times, put the screws back in and adjust.
    Cover stuff cause this is kinda messy
    Mike P, NTFDAY and glennsexton like this.

  6. #6
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    Quote Originally Posted by chasracer View Post
    We have a tendency at the track to shoot some carb cleaner into the air bleeds when the engine is running a bit rough - most of the time we get away with it but there's been a time or two where we made it worse and had to pull things apart to fix it.
    Actually, it didn't make it worse, it just sped up the inevitable. Sometimes the magic doesn't work.

  7. #7
    zaneyboi is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2021
    Location
    Gadsden
    Posts
    16

    Thanks for the reply! I'm more used to fuel injected applications and am fairly new to carbs but still know my way around one in terms of basics. But yeah what you said makes no sense about it going richer than initial start then dead lean in less than a minute after. But I have tried changing the primary jets from the 78s that were in it all the way to 82s and it will change how it first idles but still ultimately goes dead lean. I do not understand in the slightest what is going on.

  8. #8
    zaneyboi is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2021
    Location
    Gadsden
    Posts
    16

    The only vacuum I have goes to the vacuum advance and brake booster. I have a carb spacer with a vacuum fitting that I used to T off for both vacuum advance on the distributor and the brake booster. And I do not have a PVC valve I just vent to atmosphere. And I will take the carb off and try cleaning it perhaps...

  9. #9
    zaneyboi is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2021
    Location
    Gadsden
    Posts
    16

    I am using an AFR gauge.

  10. #10
    zaneyboi is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2021
    Location
    Gadsden
    Posts
    16

    Thanks I will try that after work.

  11. #11
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    You need to think in terms of circuits. Sitting at idle in the driveway, you'll be using ( you guessed it) the idle circuit! The 2 needle valves can effect your readings at the AFR... that's it, they will do little else for this conversation. The jets you speak of will only work off idle, so changing them to any number and then doing readings at idle doesn't work.

    That's why I was saying to drive the car around and at different rpm ranges, then take readings at a given rpm/speed! There is also a power valve for wide open throttle,these are known to leak on some carbs. So you will have an opportunity to get the opening value when you have it apart. With that number on hand... get a vacuum gauge and take a reading, usually you use a valve that's 1/2 of what ever your highest reading is on the gauge. But if you want to "tune" the valve you can use a higher or lower setting to open the power valve sooner or later as you desire. These are all just basics.. I'm hoping you can report back that you found some debris that fouled the carb and get rid of those huge jets you went to! LOL..
    Dave Severson, NTFDAY and 36 sedan like this.

Reply To Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink