Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree7Likes
  • 2 Post By Hotrod46
  • 1 Post By randyr
  • 2 Post By jerry clayton

Thread: Brake Lines
          
   
   

Reply To Thread
Results 1 to 10 of 10
  1. #1
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,988

    Brake Lines

     



    Yesterday I went to move the old '90 F150 and the brake pedal went to the floor and I found a pinhole leak in one of the hard lines feeding the RF caliper - rusted thin, and blown out. The truck is too dangerous to drive as it is (with that line fixed), and it's time to replace all of the brake lines.
    I'm looking for a really good flaring setup, along with a good bender. Seems to me that I've seen recommendations here before, but searching for specifics, well

    Also any tips on fitting/flare types used for that era? I'm a flaring rookie, for now.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  2. #2
    Hotrod46's Avatar
    Hotrod46 is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2007
    Location
    Vidalia
    Car Year, Make, Model: 1946 Ford Coupe, 1962 Austin Healey 3000
    Posts
    1,496

    Most all I've ever used were Ridgid brand. Both for bending and flaring. Not the cheapest, but they work as they should. My 45* flaring tool is one that my Dad picked up somewhere in the 60's and I can't remember the brand. My 37* tool is Ridgid.

    The more expensive bending tools usually have a tighter radius bend. I've used a cheap HF bender on occasion, but they make a large radius bend that might not fit some places. About the only time I use the HF tool is when I'm bending 5/16 tubing for transmission lines. The HF bender is the only one I have in that size. To save some money, I use a 1/4" tool for both 1/4" and 3/16". This hasn't caused any issues.

    The Ridgid flaring tools have a slip clutch so that you don't over flare. The idea is to form a seat, but some folks crank the tool down and deform the flare.

    Get a decent tubing cutter and be sure to deburr the cut end. I have found that a cheap HF step bit in a cordless drill works great for deburring. You will most likely need a 45* double flare for your truck.

    Make sure the flaring tool you get does double flares. This takes additional double flaring spuds to form. Generally the thickness of the flange on the spud is used to measure how far the tubing sticks through the flaring tool. The spud is used to form a swell on the tube and then the spud is removed and the flare folded back into itself. A small drop of oil on the underside of the spud makes the forming go a little easier.

    Also, when you are test fitting 45* double flares, don't tighten the fittings up. Just snug them finger tight. The tiny double flare seat in the female part is usually brass and easily damaged. Save the tightening for the final assembly.
    Last edited by Hotrod46; 09-11-2017 at 07:16 AM.
    ted dehaan and NTFDAY like this.

  3. #3
    RichB's Avatar
    RichB is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2013
    Location
    Portage
    Car Year, Make, Model: 31 A Coupe
    Posts
    567

    Iv'e got the Eastwood flaring tool as mentioned by Denny. I love it, the best I have ever used!
    Imperial are great benders, top quality.

    Rich
    http://www.clubhotrod.com/hot-rod-bu...del-coupe.html

  4. #4
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,988

    Quote Originally Posted by RichB View Post
    Iv'e got the Eastwood flaring tool as mentioned by Denny. I love it, the best I have ever used!
    Imperial are great benders, top quality.

    Rich
    Thanks, Rich. I'd seen the Eastwood tool, but didn't want an OUS POS that turns good tube to scrap. Thanks too, Hotrod46 for all of the tech tips!
    Last edited by rspears; 09-11-2017 at 10:23 AM.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  5. #5
    randyr's Avatar
    randyr is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2007
    Location
    Santa Monica
    Car Year, Make, Model: 37 Ford tudor humpback
    Posts
    1,987

    Roger, somewhere along in that era, they started using bubble flares instead of 45 double-inverted flares. The bubble flares require a little different setup unless you get a tool that does both. I ran into this drama when installing the '92 8.8 disc brake rear under my truck. I saw a youtube video showing how to make bubble flares with a standard tool but I had no luck with that. I ended up buy a few lines with bubble flares then cutting them to length and doing a regular flare on the other end when mating the older stuff to the newer stuff.
    I also have a Rigid flaring tool with standard U.S. sizes. It doesn't hold the metric lines very well at all. I don't know if your truck has metric or standard but you'll probably want to sort that out before purchasing.
    rspears likes this.
    "It is not much good thinking of a thing unless you think it out." - H.G. Wells

  6. #6
    40FordDeluxe's Avatar
    40FordDeluxe is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2011
    Location
    Prairie City
    Car Year, Make, Model: 40 Ford Deluxe, 68 Corvette, 72&76 K30
    Posts
    7,264
    Blog Entries
    1

    I have this tool below and really like it. Too bad I paid a lot more than this for it. The body style ford pick up I think you're working on, I've seen them use standard lines but metric tube nuts so watch for that too.


    https://www.amazon.com/s/?ie=UTF8&ke...mxs8nuwi_b_p19
    Ryan
    1940 Ford Deluxe Tudor 354 Hemi 46RH Electric Blue w/multi-color flames, Ford 9" Residing in multiple pieces
    1968 Corvette Coupe 5.9 Cummins Drag Car 11.43@130mph No stall leaving the line with 1250 rpm's and poor 2.2 60'
    1972 Chevy K30 Longhorn P-pumped 24v Compound Turbos 47RH Just another money pit
    1971 Camaro RS 5.3 BTR Stage 3 cam, SuperT10
    Tire Sizes

  7. #7
    Matt167's Avatar
    Matt167 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2004
    Location
    Prattsville
    Car Year, Make, Model: '51 Chevy Fleetline and a Ratrod project
    Posts
    4,990

    Cal Van Tools inline flaring tools. The kit is like $50 but you can buy single die kits cheap if you only need one or 2... Does metric or standard, double flare or bubble flare

    I had a '96 F150 and as far as I remember the brake lines were standard. I don't know about into the ABS systems. Those systems were not built by Ford and probably overseas so they might be bubble flare or metric.

    Oh and Nicopp lines. You can't screw up a flare with nicopp, and with it your doing the job once because it will never rust out.
    You don't know what you've got til it's gone

    Matt's 1951 Chevy Fleetline- Driver

    1967 Ford Falcon- Sold

    1930's styled hand built ratrod project

    1974 Volkswagen Super Beetle Wolfsburg Edition- sold

  8. #8
    jerry clayton's Avatar
    jerry clayton is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2006
    Location
    Bartlett
    Posts
    6,831

    Take the old line off the truck and measure it then auto parts store-they have lengths of tube alrady flared with whatever fittings you want---------that way you won't have to spend $$$$$$$$$$$$$$$ on stuff you don't use every week
    DennyW and 53 Chevy5 like this.

  9. #9
    53 Chevy5's Avatar
    53 Chevy5 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2005
    Location
    Doon, Ia
    Car Year, Make, Model: 53 Chevy 3100
    Posts
    2,708

    I did what Jerry did. My double flare tool was hit and miss on my last project. On the 53, I went to Carquest and got pre made brake line in the closest length that would work and if necessary I would buy a union. It was cheap and easy, I don't think I spent $50.
    Seth

    God cannot give us a happiness and peace apart from Himself, because it is not there. There is no such thing. C.S.Lewis

  10. #10
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,988

    Quote Originally Posted by 53 Chevy5 View Post
    I did what Jerry did. My double flare tool was hit and miss on my last project. On the 53, I went to Carquest and got pre made brake line in the closest length that would work and if necessary I would buy a union. It was cheap and easy, I don't think I spent $50.
    That's probably the smartest way to do it, and I have used the pre-mades before. The OEM lines have all kinds of kinks & bends to them, some of which are not really needed, and if the line's 8" too long a couple of zig-zags takes care of the extra. It's just an ol' beater truck to use on the property at this point, so I don't need for the runs to look pretty. It'll likely be quicker too.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink