Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree25Likes

Thread: ignition problems
          
   
   

Reply To Thread
Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 16 to 30 of 33
  1. #16
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    No harm / No foul... adding value?? Your participation is value enough!

    As the kids used to say, Chill Out! It's all good..
    36 sedan likes this.

  2. #17
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    Ditto what 34-40 said rspears, you add more than you miss!

  3. #18
    papajoe49 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2015
    Location
    Windsor
    Posts
    8
    Blog Entries
    2

    ignition problems

     



    hey guys its papajoe again. Put a new alternator in and have 14.5 volts going to the battery.took it for a run and it ran great ran it for about a half hour volt meter said 14.5 volts. Started it uo tonight and it fired right off. Went for a drive about 15 minutes into it slowly shut down started coughing and quit don't know where to go put a brand new module in yesterday...Take any help I can get. its a 350sb mild cam bare bones..DUI dist. New everything..Cant seem to get a handle on it!!!!!

  4. #19
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,987

    Joe, in the other thread that you posted on MikeP went through his HEI, and the problem he described sounds exactly like what you're experiencing with yours.
    Quote Originally Posted by MikeP
    I found what I figured I would, a broken wire between the pickup coil and the module plug. As the pickup coil is stationary and the module is attached to the breaker plate the wires flex as the breaker plate moves back and forth. In this case the flexing eventually caused the wire to break, at idle with the wire relaxed the 2 ends of the broken wire made contact, but when vacuum was applied and the breaker plate rotated the wire pulled apart.
    Do you have a book on that distributor, so that you're confident pulling it apart and putting it back together? I'd say you're to that point, or else shopping for a replacement distributor for it. Then you can post mortem this one at your leisure, and have it as a shelf spare, or for the next build.
    glennsexton and 36 sedan like this.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  5. #20
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    Do you have a electronic tach connected to the distributor? If so, disconnect the tach wire at the distributor and try it. A bad tach will cause all kinds of trouble with HEI.
    NTFDAY and rspears like this.

  6. #21
    jerry clayton's Avatar
    jerry clayton is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2006
    Location
    Bartlett
    Posts
    6,831

    You have a situation where the higher degree of spark is IONizing the air inside the dist cap-------was a common (well not too common) problem when the MSD 7 units came out and were run on engines up around 10000rpm. With the air ionized the spark just went all over causing some of what your discussing--------


    On a race engine it was easy fix to just drill 8 1/2 inch holes between all the terminals however on a street engine this isn't a very good fix because of everyday street conditions----

  7. #22
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    Had a similar thing happen on several cars back in the 80's that had HEI. Would run great and then run crappy. I would take the cap and rotor off to look at the module or change the module. All would be great for a while then it repeated. Eventually every car that did this died. On one, I started looking at the rotor....under the contact for the center, there was a tiny hole eroded. There was some faint carbon tracking thru the hole that grounded the rotor to the distributor shaft thru this hole.....it seemed to be heat related to the conductivity... and related to me removing the rotor to change the module....I would destroy the carbon path and it took a drive to re-establish it. I also found that cheap crap rotors were the worst, real Delco rotors (the whitish ones) were the least susceptible to the problem. I talked to a couple of shops who admitted to making quite a profit by changing rotors but charging for a module. Also, look at the cap inside for tracking....it is really faint.
    Mike in Tucson
    NTFDAY, glennsexton and 36 sedan like this.

  8. #23
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,333

    An absolute must is a cap and rotor of high dielectric strength. For those of you who aren't familiar with that term it merely means components that are constructed of material that has a high opposition to current flow. MSD and other quality manufacturers, I assume, are you sort sort of bakelite material for their caps and rotors.
    This will explain it much better than I can.
    https://en.wikipedia.org/wiki/Bakelite
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  9. #24
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    And I'll keep beating this old problem, make certain you have good grounds, engine to chassis, chassis to body, body to battery, battery to chassis, battery to engine. There is no such thing as too many grounds on a car or truck.

    .
    Rrumbler and glennsexton like this.
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  10. #25
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    Roger that, Tech - I have a #6 directly from the negative post on the battery to a ground bar under the dash where I make all ground connections. This is in addition to a pair of straps between the body and frame, and two from engine to frame. Need to attach to bright shiney metal as well - paint (especially powder coat) is a great insulator.
    techinspector1 likes this.
    "Where the people fear the government you have tyranny. Where the government fears the people you have liberty." John Basil Barnhil

  11. #26
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    By the way, ACCEL components are in the "worst" category for dielectric longevity. I am surprised that Accel stuff makes it home from the store before dying.

  12. #27
    papajoe49 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2015
    Location
    Windsor
    Posts
    8
    Blog Entries
    2

    Unhappy ignition problems

     



    thanks for the input guys..i have tried all the suggestions, even made a list put a new summit mod in last night and it quit in about 15 min then would not start at all pulled it out and had it tested, it was bad this was mod 6 cant afford to keep throwing mods at it..uhave checked everything you guys have suggested, disconnected the tack today and will see what happens tonight ...again many thanks papajoe

  13. #28
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,987

    Joe, what type of compound are you using between the module and the mounting surface on the distributor?
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  14. #29
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    Have you contacted DUI products about this?

  15. #30
    papajoe49 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2015
    Location
    Windsor
    Posts
    8
    Blog Entries
    2

    Ignition problems

     



    Have contacted DUI company about moduels...As you would expect they have never had any proplems with their distributors..go figure..

Reply To Thread
Page 2 of 3 FirstFirst 1 2 3 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink