Search:
Type: Posts; User: richmondb
-
12-20-2006 03:28 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I have a 350 bored 30 over. The cylinders...
I have a 350 bored 30 over. The cylinders measure 4" exactly. World products S/R Torquer 67 cc heads, Comp cams XE268, edelbrock performer intake, I just ordered some Thorley tri Y headers. The...
-
12-19-2006 05:25 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
The block looks good. I only drove it about 1...
The block looks good. I only drove it about 1 mile after it happened and that was at 30 mph. What type of head gasket should I get to stop this from happening again. I have a 4" cylinder, should I...
-
12-18-2006 05:38 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I just got the passenger side head off and sure...
I just got the passenger side head off and sure enough, you guys were right. The head gasket is blown right between the two middle cylinders! Man you guys are good. That is a cheap fix. Lots of...
-
12-18-2006 01:26 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I checked the rest of the cylinders. I actually...
I checked the rest of the cylinders. I actually have two bad ones. Both middle ones on the passenger side of the engine. Could that be a blown head gasket? That would probably be the best case...
-
12-18-2006 12:21 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
Well, I did a compression check and sure enough I...
Well, I did a compression check and sure enough I have a cylinder with 0 psi :( I pulled both rocker arms and they looked fine. Both push rods looked fine also. The springs don't seem to be...
-
12-17-2006 04:45 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I hope this problem turns out to be something...
I hope this problem turns out to be something that cheap. I checked the PCV, it rattles when I shake it.
-
12-17-2006 03:24 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
Yeah, no loud clicking or smoke out the exhaust. ...
Yeah, no loud clicking or smoke out the exhaust. Oil pressure is fine. That's why I am leaning towards the coil going bad.
-
12-17-2006 01:45 PM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
What is a collapsed lifter? I will do the...
What is a collapsed lifter? I will do the compression check tomorrow and let you know the results. I think I would rather it be a bad coil than have to mess with replacing a spring or a lifter.
-
12-17-2006 10:40 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I'm going to go buy a gauge to do the compression...
I'm going to go buy a gauge to do the compression check. I just have to take out a spark plug and screw the gauge into the plug hole and then crank over the engine with the battery disconnected to...
-
12-17-2006 10:23 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I have an edelbrock q-jet with the big...
I have an edelbrock q-jet with the big secondaries. They are closed. I am not sure about what you are refering to as the upper and the lower. The two back valves on top of the carb are closed. ...
-
12-17-2006 10:02 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I didn't change anything from the way it was set...
I didn't change anything from the way it was set up when we put the engine in it 1000 miles ago. You don't think it has anything to do with the valvetrain? I was messing with the ground on the...
-
12-17-2006 09:45 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
Do you think it could be the coil not able to...
Do you think it could be the coil not able to create enough spark when I give it gas. That would make since. Do they go bad all of a sudden like that?
-
12-17-2006 09:30 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I tried checking that but I didn't see any spark...
I tried checking that but I didn't see any spark when I removed the plug wire and held it next to the engine while it was running. Should it be strong enough to come out of the boot and hit the...
-
12-17-2006 09:20 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
:) I wish I could. It sounds like an old tired...
:) I wish I could. It sounds like an old tired engine that chugs when you press the gas. Sounds kinda like a lawn mower.
-
12-17-2006 09:16 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
Vacuum secondaries, and they're closed.
Vacuum secondaries, and they're closed.
-
12-17-2006 09:04 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I have been doing some searches and reading up on...
I have been doing some searches and reading up on the problem I am having. I am worried that maybe I lost a cylinder or something by bending a push rod or breaking a spring. Is it possible to jump...
-
12-17-2006 09:00 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
I can't say for sure if the valves moved up and...
I can't say for sure if the valves moved up and down exactly the same amount. They all moved up and down and I didn't notice any differance in the distance traveled. The carb was getting plenty of...
-
12-17-2006 08:55 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
It was running fine before I mashed on the gas. ...
It was running fine before I mashed on the gas. I changed out the fuel filter but that didn't fix it.
-
12-17-2006 08:19 AM
Thread: popping through carb
by richmondb- Replies
- 38
- Views
- 7,263
popping through carb
Okay, I think I screwed something up. I have a 350 recently rebuilt (1000 miles ago), edelbrock q-jet carb, XE268 cam. I took it out yesterday for a spin and got on it a little bit. All of a...
well I decided to do another mod to gain max travel of bars past the intended travel points just for that peace of mind. 1/8 inch is to close so now I'll have 1/2" or better. I cut a 3/16" wall...
New Project