Search:
Type: Posts; User: jawarner
-
05-14-2010 01:33 PM
- Replies
- 30
- Views
- 19,716
Hello Everyone, I appreciate all the knowledge...
Hello Everyone,
I appreciate all the knowledge and insight into this topic. On my 4th attempt, I think I have it sealed. (Knock on wood because it has only been 2 weeks of leak free service). I... -
04-18-2010 08:25 PM
- Replies
- 30
- Views
- 19,716
Sorry to hear that Randy. That is the tough thing...
Sorry to hear that Randy. That is the tough thing about the FE motor. That gap where the cork gasket goes is huge. As I wrote earlier in the thread, I spoke with both Edelbrock and Permatex, both...
-
04-18-2010 06:16 PM
- Replies
- 30
- Views
- 19,716
I was very thorough in cleaning the surfaces. I...
I was very thorough in cleaning the surfaces. I used Permatex's Gasket Remover following by a parts cleaner and a scotch-brite pad. On the manifold, I also hosed it off and blew it out just to make...
-
04-18-2010 08:07 AM
- Replies
- 30
- Views
- 19,716
Thanks for the description and thoughts. Like I...
Thanks for the description and thoughts. Like I said, I am getting desperate and am willing to consider any and all ideas. I most certainly will try the center punch idea as I don't think it can hurt...
-
04-18-2010 12:21 AM
- Replies
- 30
- Views
- 19,716
Hello guys, I put the engine back together...
Hello guys,
I put the engine back together using the end gaskets and the finger full method. I've put about 3 hours on the engine since and I thought I was home free. This afternoon I looked under... -
02-24-2010 03:36 PM
- Replies
- 30
- Views
- 19,716
I agree with you John, even on the aluminum...
I agree with you John, even on the aluminum manifold. I am not sure what about an aluminum manifold would make the cork gasket slide out any faster than the heavy cast manifold from the factory....
-
02-23-2010 08:38 PM
- Replies
- 30
- Views
- 19,716
Thanks John. I'll definitely get another set of...
Thanks John. I'll definitely get another set of hands to help me.
By the way, I called Edelbrock today. After being on hold for 30 minutes I spoke with a technician. He said the reason they... -
02-22-2010 09:54 AM
- Replies
- 30
- Views
- 19,716
Guys, thanks for all the input on this. I...
Guys, thanks for all the input on this.
I decided I might as well bite the bullet and tear it down. Upon removing the manifold, I saw a pin hole sized void in the RTV close to the front right... -
02-21-2010 10:46 AM
- Replies
- 30
- Views
- 19,716
Thanks for the posts. I have tried to rule out...
Thanks for the posts. I have tried to rule out all the simple things. Tightening the valve covers seemed to slow it a little but I still don't think that is it. (Just wishful thinking).
Assume it... -
02-21-2010 10:31 AM
- Replies
- 30
- Views
- 19,716
Thanks for all the input guys. I've taken the...
Thanks for all the input guys. I've taken the suggestion and tried to rule out all the other stuff (valve covers etc). I just don't see any sign the leak is coming from anywhere but the intake....
-
02-21-2010 07:51 AM
- Replies
- 30
- Views
- 19,716
Thanks for the reply. Would you feel the same...
Thanks for the reply. Would you feel the same about the rubber gaskets on the ends?
Also, before I pull it apart, is there any way I can absolutely be sure it is the intake that is leaking? I used... -
02-20-2010 09:24 PM
- Replies
- 30
- Views
- 19,716
Thanks John, This is very similar to what my...
Thanks John,
This is very similar to what my relative told me. On the "finger" full of sealer, would you use that "right stuff"?
A quick question for you. I can't explain why this suddenly... -
02-20-2010 08:46 PM
- Replies
- 30
- Views
- 19,716
FE Intake Oil Leak -- End Gaskets or Not?
Hello. I am new to the forum and need some help.
I have a 69 Mustang with an FE Motor I've rebuilt. It has Performer RPM Heads and matching Performer RPM Intake Manifold. The installation...
here's the latest, I had to cut up the cross section of the frame to get the parallel bars in place and these pic's show my fix . 3 x 6 tube used to rebuild the frame section. [/URL] after lots...
New Project