I agree with the other guys, nice work, and a great old lathe! When in comes to heavy tools I find the quality from the past much supperior to what you will pay for anything new these days. I do wood working and really like pre-chinese stuff!
Printable View
I agree with the other guys, nice work, and a great old lathe! When in comes to heavy tools I find the quality from the past much supperior to what you will pay for anything new these days. I do wood working and really like pre-chinese stuff!
Progress on suspension. Made upper spring/shock mounts from 1/4" thick 6" wide flat bar. In the front, tubing comes up from the subframe to a brace that will bolt in place. It will be removable to extract the struts without separating ball joints and tie rods.
[IMG]https://c1.staticflickr.com/1/361/31...6044fcba_b.jpg20170119_093043_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/435/32...68438606_b.jpg20170119_094333_resized by Ben Modified, on Flickr[/IMG]
The brace will be clamped in place temporarily to determine proper ride height.
Once determined, a flange nut will be welded into the top of the trimmed off tube. Will also weld a plate over the 1 1/2" hole thru which the bolt will go.
[IMG]https://c1.staticflickr.com/1/599/32...fd823110_b.jpg20170120_093328_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/453/31...3f251d2e_b.jpg20170120_102302_resized by Ben Modified, on Flickr[/IMG]
Heated and bent the ends of the tubes to match the strut angle
[IMG]https://c1.staticflickr.com/1/782/31...50013ab5_b.jpg20170120_123356_resized by Ben Modified, on Flickr[/IMG]
Started on the rear supports also. Mostly done, just need a couple of gussets.
[IMG]https://c1.staticflickr.com/1/299/31...a3bbe055_b.jpg20170120_171918_resized by Ben Modified, on Flickr[/IMG]
The supports are out from under the car. The front is on its wheels and the rear in on a floor jack waiting for the gussets.
[IMG]https://c1.staticflickr.com/1/483/32...dac0866d_b.jpg20170120_124742_resized by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
Part 3 is on YouTube
https://www.youtube.com/watch?v=h25zc-lF1bc
The steering is coming together. I wound up using a center steer box from a sand rail with the steering arms from the gen 1 honda crx and the tie rod ends from the miata. Here is the original sand rail setup
[IMG]https://c1.staticflickr.com/1/276/31...ea8b38f9_k.jpg20170123_145418 by Ben Modified, on Flickr[/IMG]
The new arrangement
[IMG]https://c1.staticflickr.com/1/528/31...2bc479ba_k.jpg20170123_145415 by Ben Modified, on Flickr[/IMG]
Had to open up the holes in the ends of the rack and rethread to fit the honda pieces.
[IMG]https://c1.staticflickr.com/1/392/31...a6cdbfa1_k.jpg20170123_145438 by Ben Modified, on Flickr[/IMG]
Assembled with the beginnings of a mounting bracket. I believe that shock boots from a golf cart shock will work on this unit.
[IMG]https://c1.staticflickr.com/1/349/32...2be7d123_k.jpg20170124_151839 by Ben Modified, on Flickr[/IMG]
The joints are in the original miata location. With any luck, no bump steer. I will cycle the suspension thru its range before welding everything in
[IMG]https://c1.staticflickr.com/1/260/31...b5377a98_k.jpg20170124_125238 by Ben Modified, on Flickr[/IMG]
Also machined some collars to splice the rear axles
[IMG]https://c1.staticflickr.com/1/380/32...d74452d5_k.jpg20170124_161452 by Ben Modified, on Flickr[/IMG]
And welded in a couple of pieces of tubing for the cage
[IMG]https://c1.staticflickr.com/1/700/31...b54eb7e6_k.jpg20170124_160122 by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
Took the body off again today to get to a few spots for welding and steering work.
[IMG]https://c1.staticflickr.com/1/711/32...e640443a_b.jpg20170125_172248_resized by Ben Modified, on Flickr[/IMG]
Added a few gussets to the uprights that support the front spring upper brace.
[IMG]https://c1.staticflickr.com/1/651/32...46898898_b.jpg20170125_172209_resized by Ben Modified, on Flickr[/IMG]
Center steer mount
[IMG]https://c1.staticflickr.com/1/719/32...9f2feb7c_b.jpg20170125_172216_resized by Ben Modified, on Flickr[/IMG]
I bolted in the rack system and ran the front suspension thru its travel range with no perceptible bump steer! Sorry, no photo
http://www.BenModified.com
Very nice work!
Very cool; great fab work!
Thanks! Here is todays progress
Temporarily installed the rack today. Still need to find some properly sized bellows.
[IMG]https://c1.staticflickr.com/1/545/32...a72cb484_b.jpg20170126_084449_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/421/32...ccaf0583_b.jpg20170126_084711_resized by Ben Modified, on Flickr[/IMG]
Also did some work on the braking setup. I am taking advantage of the extra room with the body off to locate and install the pedal assembly. I am using the originals from the car and adapting a 1970 VW Bug master cylinder. This mc is intended for four wheel drums, but I have used them before on 4 wheel discs with good results.
[IMG]https://c1.staticflickr.com/1/748/31...bf5cba37_b.jpg20170126_085456_resized by Ben Modified, on Flickr[/IMG]
It only required elongating the mc mounting holes and a little filing to open up the opening on the pedal assembly.
[IMG]https://c1.staticflickr.com/1/599/31...b7fde561_b.jpg20170126_085506_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/364/32...92052e6b_b.jpg20170126_085515_resized by Ben Modified, on Flickr[/IMG]
I sandwiched a piece of 3/16" metal plate between the two to create a mounting system
[IMG]https://c1.staticflickr.com/1/275/32...ec4a098c_b.jpg20170126_140805_resized by Ben Modified, on Flickr[/IMG]
Only needed slightly longer mounting studs
Also cut a couple of strips of metal to sandwich the body sheet metal. The roll cage tubing is located beneath these strips. The holes are for welds to the tubing. The uprights that hold the upper strut mount come up thru these strips and will be welded together.
[IMG]https://c1.staticflickr.com/1/537/31...638da7f4_b.jpg20170126_152624_resized by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
You are rollin on this thing, thanks for the updates !
Nice rack! Never seen one so tiny. You're doing some wild engineering on that thing.
Here is todays progress
Welded in the master cylinder brackets
https://c1.staticflickr.com/1/310/32...4996e4be_b.jpg20170127_144303_resized by Ben Modified, on Flickr
Finished the upper strut brace
[IMG]https://c1.staticflickr.com/1/490/32...10618c7d_b.jpg20170127_165958_resized by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
Started piecing together the steering column. Welded on some heim joint mounting bosses.
[IMG]https://c1.staticflickr.com/1/570/32...ded5c929_b.jpg20170128_184956_resized by Ben Modified, on Flickr[/IMG]
I am using a piece of 3/4" shaft with a keyway temporarily. I left it very long and made up an adaptor to the steering wheel so that I can slide the wheel to different positions on the shaft for the best position
[IMG]https://c1.staticflickr.com/1/730/32...ee61cfbe_b.jpg20170128_182418_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/491/32...a1025346_b.jpg20170128_182324_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/732/32...7f7abb89_b.jpg20170128_182310_resized by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
Part 4 is on YouTube
https://www.youtube.com/watch?v=-gSnb3W55wo
I put the body back on the chassis today and started welding the two together.
[IMG]https://c1.staticflickr.com/1/392/31...b47f5216_b.jpg20170130_175810_resized by Ben Modified, on Flickr[/IMG]
The front braces are welded together with the cage tubes under the dash
[IMG]https://c1.staticflickr.com/1/598/32...5865ceca_b.jpg20170130_143112_resized by Ben Modified, on Flickr[/IMG]
[IMG]https://c1.staticflickr.com/1/443/32...b68cb0d1_b.jpg20170130_143054_resized by Ben Modified, on Flickr[/IMG]
Working on connection on the rear of the car
[IMG]https://c1.staticflickr.com/1/396/32...a9598ef3_b.jpg20170130_175844_resized by Ben Modified, on Flickr[/IMG]
http://www.BenModified.com
"I put the body back on the chassis today and started welding the two together."
Uh oh, now your commited for sure, cant wait to see this thing in motion !