Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: How do you measure vacuum?
          
   
   

Reply To Thread
Results 1 to 6 of 6
  1. #1
    sfort's Avatar
    sfort is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2009
    Location
    Allen
    Car Year, Make, Model: 46 Chevy Truck
    Posts
    528

    How do you measure vacuum?

     



    When I rebuilt my carb (670 street avenger, engine 60 over 454, cam RV) I adjusted the idle mixture screws with a vacuum cage plugged to the intake port for the transmission. I adjusted the screws according to the best vacuum/highest reading at idle. Was that the correct way or did I luck out "and find and acorn"? Truck is running fine. I saw something the other day posted saying the adjust with the car in gear. Gage I was using was one that is also used to bleed brakes.

  2. #2
    cffisher's Avatar
    cffisher is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Constantine
    Car Year, Make, Model: 57 chevy 2 dr wagon
    Posts
    9,476

    I always use a vacuum guage just as you did. I suppose there are other ways but thats how I learned.
    Charlie
    Lovin' what I do and doing what I love
    Some guys can fix broken NO ONE can fix STUPID
    W8AMR
    http://fishertrains94.webs.com/
    Christian in training

  3. #3
    IC2
    IC2 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    UPSTATE New York
    Posts
    4,336

    You'll be fine with doing it as you did. Putting it in gear, setting the e-brake, hopping out to blip the throttle is a fine way to see your vehicle go winging through the back of the garage - maybe with you hanging on to the throttle linkage for dear life.

    Usually, smooth idle, 15-21 inches of vacuum with a stock to mild cam, and none to very little needle movement at idle is what you are looking for. An ~4" gauge is best, but a small, 2-1/16" will usually get you close enough
    Dave W
    I am now gone from this forum for now - finally have pulled the plug

  4. #4
    angrystroker's Avatar
    angrystroker is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2011
    Location
    Earth
    Posts
    247

    Without vacuum gage, you can adjust for the leanest, highest idle RPM and back off 1/4 turn on both sides. That will fatten it up enough so as to idle good in drive. Definitely do not attempt to run adjustments in gear, someone was pulling your leg there.
    Is that your face or did your pants fall down?

  5. #5
    sfort's Avatar
    sfort is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2009
    Location
    Allen
    Car Year, Make, Model: 46 Chevy Truck
    Posts
    528

    Thanks guys. Thought I was right!

  6. #6
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    I just picked up a nice guage off eBay. It measures pressure and vacuum, came with adapters, I think I got it for under $20, and it already paid for itself. It showed me the fuel pressure was fine, 7psi, and manifold vacuum was low. I sprayed carb cleaner around the manifold tll I found the leak.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink