Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Hi-Ram Tunnel Ram
          
   
   

Reply To Thread
Results 1 to 8 of 8
  1. #1
    ra7tnast is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    ksa
    Posts
    5

    Hi-Ram Tunnel Ram

     



    what about the Manifolds Hi-Ram Tunnel Ram, in stroker engine 383?
    the Carburetors edelbrock 1500cfm?

  2. #2
    erik erikson's Avatar
    erik erikson is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    clive
    Car Year, Make, Model: BLOWN 540 57 CHEVY
    Posts
    2,878

    Quote Originally Posted by ra7tnast
    what about the Manifolds Hi-Ram Tunnel Ram, in stroker engine 383?
    the Carburetors edelbrock 1500cfm?
    Way to much carb.
    Here is the old carb forumula for size.
    Carb. CFM required = CID X MAX. RPM,then divide by 3456.

  3. #3
    skids72's Avatar
    skids72 is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2005
    Location
    Lafayette
    Car Year, Make, Model: 68 Firebird 439 BBC
    Posts
    745

    ^^^^ that's right! (actually VE*CID*maxrpm/3456 where VE is volumetric efficiency)

    Sometimes a quicker rule of thumb is CID*2 i.e. 383*2 -> 766cfm

    this shortcut assumes max rpm~7000 (3456*2) and 100% volumetric efficiency (most motors are 80% to 95% efficient).... a 750cfm carb should suffice unless you're looking to spin the motor much over 7000rpm.

    This is for minimum cfm required.... you can go larger but if you go too big the vaccuum signal will be too weak at lower rpm.

    2 cents,

    Chris

  4. #4
    kitz's Avatar
    kitz is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Austin
    Car Year, Make, Model: 32 Roadster, BBC
    Posts
    962

    Yeah but the plenum volume of a big tunnel reguires a lot more wetting out than you might think.

    Why do you want to run a tunnel ram?

    Kitz
    Jon Kitzmiller, MSME, PhD EE, 32 Ford Hiboy Roadster, Cornhusker frame, Heidts IFS/IRS, 3.50 Posi, Lone Star body, Lone Star/Kitz internal frame, ZZ502/550, TH400

  5. #5
    erik erikson's Avatar
    erik erikson is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    clive
    Car Year, Make, Model: BLOWN 540 57 CHEVY
    Posts
    2,878

    Quote Originally Posted by kitz
    Yeah but the plenum volume of a big tunnel reguires a lot more wetting out than you might think.

    Why do you want to run a tunnel ram?

    Kitz
    I was wondering when someone was going to talk about "wet flow".

  6. #6
    BigTruckDriver is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Dec 2004
    Location
    TX
    Car Year, Make, Model: hotrod
    Posts
    1,830

    Quote Originally Posted by kitz
    Yeah but the plenum volume of a big tunnel reguires a lot more wetting out than you might think.

    Why do you want to run a tunnel ram?

    Kitz
    Because it just looks freakin COOOOOL!

  7. #7
    R Pope is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    Eston
    Posts
    2,270

    A guy in Saskatoon built a small block Ford with a dual-four tunnel ram (cause it looks so COOOOOL!) and he put adapters and dual Holley two-barrels on it. Most people don't notice the diff, and he can drive the thing with no problem. Sorta like the triple carb flattie manifolds with the center carb blocked off.
    Must be a farm boy!

  8. #8
    ra7tnast is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    ksa
    Posts
    5

    thank you all

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink