Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree9Likes
  • 1 Post By 34_40
  • 1 Post By 69elko
  • 3 Post By Mike P
  • 1 Post By glennsexton
  • 1 Post By 34_40
  • 2 Post By rspears

Thread: Chevy engine decoding with Vin on block
          
   
   

Reply To Thread
Results 1 to 13 of 13
  1. #1
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    Chevy 302 327 or 350?? Let's hope it's a 302...

     



    I've got a car I'm looking at that had an older engine swapped in it and wondering if we can find out exactly what it is. It's got double hump heads so I think it might've been out of something worthwhile.
    But the numbers on the block 3914678 decode to a 302/327/350 68-79 Car & Truck 2-bolt. The engine is Chevy red paint, camel hump heads with a short water pump so I know it has to be a 60s engine right? Trucks didn't come with camel humps did they?
    Well...even better I've got a VIN on the front of the block. Can we find out what car it came out of with that?
    There's 2 sets of numbers...
    18K180469
    VO3O8EI

    What do you guys think?
    Thank you in advance.
    Last edited by 69elko; 09-07-2022 at 05:40 PM.

  2. #2
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    Ok so nastyZ28 had a little bit narrowed down info for this block. I think this is more accurate as I think it is a 1968 block. So which engine is it if it's got camel hump heads on it?

    1968 3914678 302 290 290 2/4 Camaro, Z-28
    1968 3914678 327 210 350 2 car & truck
    1968 3914678 350 295 295 2 Camaro/ChevyII

  3. #3
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    what makes you think it's the original heads? And those 302's weren't any good on the street, they needed a lot of revs to make power. it was the same deal with the boss 302 ford, the heads on the boss 302 were to big for the street. Most aluminum heads today are better than any double hump.
    glennsexton likes this.

  4. #4
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    I believe they are the original heads because the amount of grease and the paint matches perfectly. This car was sitting for quite a while so I'm pretty sure the engine hasn't been tampered with. Not a guarantee though you're right. As far as me wishing it was a 302 is because it's rare and worth more. I don't really care about it being a dog on the street I know they are.
    34_40 likes this.

  5. #5
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    It'll have a wow factor as they were a rarity. If you get it, I / We will be harrassing you for pics! LOL..

  6. #6
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    302 327 or 350?

    IMG_20220907_170930320.jpg

  7. #7
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    Well... Looks like after some deep digging I may have answered my own question. EI on the engine suffix code means it came in a Chevelle with a 327 250HP with a Powerglide. So nothing special here.

  8. #8
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Quote Originally Posted by 69elko View Post
    Well... Looks like after some deep digging I may have answered my own question. EI on the engine suffix code means it came in a Chevelle with a 327 250HP with a Powerglide. So nothing special here.
    Kinda sorry to hear that! Would've been neat to say the least.

  9. #9
    Mike P's Avatar
    Mike P is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2003
    Location
    SW Arizona
    Car Year, Make, Model: 57 Ply, 68 Ply Valiant, 83 El Camino
    Posts
    3,747

    :…… 327 250HP with a Powerglide……”


    Whatever the VIN number says it “used to be” is usually exactly that…..“what it used to be” after it goes thru it’s first rebuild.

    Normally on a rebuild, guys (especially hot rodders) will end up over boring the engine and the compression will land where it lands based on the pistons chosen to fill the holes, head gaskets used, milling etc. Often times the cam will be replaced with something that’s not even close to the factory specs. Of course, if you happen to have a better set of heads laying around chances are you end up throwing those on too. In the case of the double hump heads there were 2 flavors; one with 1.94/1.50 valves and the more desirable 2.02/1.60 valves.

    From red paint and what looks like what may have been an aftermarket timing cover I would guess that chances are the engine has at least been partially gone thru at sometime in its life.

    Anyway if it’s in a driving car and runs good enjoy it…….if it’s a candidate for a builder, I sure wouldn’t pay a premium for it. That said if the price is good it would be as good a start as any for an engine project provided it’s not already bored to the max or the crank turned to the minimum.

    Unless you’re a hardcore numbers guy DZ302 or Corvette LT1 blocks are pretty much just bragging rights unless they are in the original car.


    .
    Last edited by Mike P; 09-09-2022 at 03:46 AM.
    NTFDAY, glennsexton and 34_40 like this.
    I've NEVER seen a car come from the factory that couldn't be improved.....

  10. #10
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    The “VO3O8EI” stamping is key here for engine ID:
    V = Flint Assembly Plant
    03 = March
    08 = 8th day of the month
    EI was only used in 1968 for 250 and 275 horsepower 327 engines (both horsepower ratings had 4 barrel bolted carburetors) and all were matched to Powerglide transmissions.

    18K180469 is a partial VIN. It needs to be looked at as 1 / 8 / K / 180469;
    The 1 is the last digit of the number of the body type:
    15411 – was used for 2 door Biscayne V8
    15611 – was used for 2 door Bel Air V8
    The 8 indicates 1968 model year.
    K = Kansas, MO assembly plant
    180469 = production number. Chevy II, Chevelle started with 300001, Corvair and Corvette started with 700001 and all other Chevrolet cars started with 100001 – so this was number 180469 off the line.

    It would appear that you have a 1968, 327 from a 2 door Biscayne or Bel Air. Nothing special, just one of a gazillion 327 engines produced. If you can get the number off the heads we can tell if it’s the 250 or the 275 horsepower model.
    34_40 likes this.
    "Where the people fear the government you have tyranny. Where the government fears the people you have liberty." John Basil Barnhil

  11. #11
    69elko's Avatar
    69elko is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    San Jose
    Car Year, Make, Model: 1969 El Camino SS396 350HP
    Posts
    227

    Thanks all. The engine is in a 70 nova, it runs but has a lifter tick or something worse. So who knows what kind of condition it's in internally. The car is a project but on the pricey side so I was trying to determine if the engine was at least worth something. Doesn't look like it is so I may pass on the deal.

  12. #12
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    If it's running,and has a "tick" use that to your advantage and get the price down. It's a Small Block Chevy so it's cheaper to overhaul and make it into something more to your liking.
    glennsexton likes this.

  13. #13
    rspears's Avatar
    rspears is online now CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,989

    Quote Originally Posted by 69elko View Post
    Thanks all. The engine is in a 70 nova, it runs but has a lifter tick or something worse. So who knows what kind of condition it's in internally. The car is a project but on the pricey side so I was trying to determine if the engine was at least worth something. Doesn't look like it is so I may pass on the deal.
    In these days of LS swaps, the old Gen I SBC's only impress the "period correct" crowd. Like Mike says, try to use the "tick" to your advantage, but also throw in that you'll probably be looking at an LS package just to keep it current, and that the "value" of the project doesn't really include the power train. Those double hump heads were added just to attract attention of those who remember when they were the hot ticket, and as was said above the aftermarket aluminum heads will give you more across the board.
    Good luck! Hope you find the new project, and then keep us in the loop on your build!
    glennsexton and 34_40 like this.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink