Thread: ATF in your Oil
-
01-30-2009 10:54 AM #16
We used to add the a quart of tranny fluid to the gas tank with fillups when running in the high plains desert. It increased the vapor izing point of gas and prevented vapor lock in the old dodge vans we were using. Worked like a charm. The dodge boys claimed it would lubricate the engine too!
I'm always fearfull of miracle cures and quick fix solutions. But there are a few out there that have worked for me in the past." "No matter where you go, there you are!" Steve.
-
Advertising
- Google Adsense
- REGISTERED USERS DO NOT SEE THIS AD
-
01-30-2009 01:32 PM #17
Rebuilt the motor in my '91 Ford, 300-six. Motor was balky, didn't want to pull under 2K rpm's, missed over that. Suspected gummed up injectors from having sat for 6 months. Poured one quart of Type F auto trans fluid to 15 gals of gasoline and ran it through. Repeated with another 15 gals of gasoline. Truck smoothed right out, now pulls hard from idle to rev limit, no missing. Have not emission tested motor since then. Don't know if the 60:1 ratio of fuel to oil would do any harm to the catalytic converters, but it sure fixed the injectors.PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.
-
01-30-2009 02:21 PM #18
Conventional transmission fluid and 5W-20 are both “highly refined mineral oil”. The average viscosity for transmission fluid at 40 degrees C is +/- 42cSt and 5W-20 is +/- 48cSt. Both contain detergents however; by composition, motor oils typically carry a greater percentage of the detergents.
API ratings of “SJ”, “SL”, or “SM” all contain high detergent content to lessen tailpipe emissions. API “SA” and “SB” ratings were the last totally "non-detergent" oils and these oils were typically single grade, i.e., 30W – and have not been commercially available for some time. Synthetics are a different composition altogether.
I think where people often see ATF working a cleaning agent is if they have been using “heavier viscosity” oils or have been running their engines a bit low on oil and deposits have started to build up. The introduction of transmission fluid in such cases would certainly lower the viscosity allowing suspension of particulate matter (carbon) which makes the oil look very dark. Performing this procedure on an older engine can have a very impressive result in the first oil change.
Several products have been introduced over the years (anyone else remember Rislone? - Basically the same effect as Techinspector w/ some tranny fluid in the gas.) that worked to varying degrees.
I know that everyone has an “oil story” where they ran 80W or straight STP in an old engine with a bazillion miles on it. My point was that modern 5W-20 does a fine job without any additives (transmission fluid or otherwise) on an engine that sees regular oil/filter changes.
Regards All,
Glenn
-
01-30-2009 03:06 PM #19
Years ago when I was manager of a car wash, this guy brought his charger with a 383 engine in that was knocking real bad. We took his valve covers off and most of the rockers were getting no oil. We put a can of the ATF in a within a minute the oil was spraying over the engine. We also dumped some car cleaner like Denny mentioned, just enough to keep the engine going and talk about smoke. It filled the whole bay up.Keep smiling, it only hurts when you think it does!
-
01-30-2009 03:55 PM #20
Ive never been told it would clean an engine, but i heard it`s a quick way to get bearings to stop making noise if your trying to pass a bum car to some smuck. A mechanic that lived down the street from me when i was around 15 told me that, or you could add straight gear oil if the motor was really dead.
wow just fantastic craftsmanship !!
55 Wagon Progress