Thread: Engine angle
Results 1 to 8 of 8
LinkBack URL
About LinkBacks-
03-31-2006 04:33 PM #1
Registered User
- Join Date
- Mar 2006
- Location
- Rogers
- Car Year, Make, Model: 1940 Dodge Coupe
- Posts
- 1
Engine angle
I have installed a new fat man suspension on my 1940 Dodge. I am getting ready to test fit the motor and mount the motor mounts. I am curious how much of an angle the motor should have? I am pretty sure the engine does not sit in the car perfectly level. The angle will affect the carb floats, so I think this is important.
Thx in advance.
Rick
-
Advertising
- Google Adsense
- REGISTERED USERS DO NOT SEE THIS AD
-
03-31-2006 04:56 PM #2
CHR Member
- Join Date
- Jan 2006
- Location
- fort myers
- Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
- Posts
- 11,033
Ideally, you should be able to lay a carpenters level on the carb mounting surface and install the engine dead level. I've rarely been able to hit it right on, because of clearance issues or cosmetics.
My daily driver Jeep has the 5.0 mounted on about a 3 degree rearward slant, and it has worked fine for years. My '27 sits on about the same slant, no problems.
But if you ask the experts, it should be dead level. Sometimes there is the "perfect world" and other times, the "real world."
JMO,
Don
-
03-31-2006 04:57 PM #3
CHR Member
- Join Date
- Jan 2004
- Location
- Prattsville
- Car Year, Make, Model: '51 Chevy Fleetline and a Ratrod project
- Posts
- 4,990
3* to the rear of the vehicle. intake manifolds are cut at 3* to the front, so that they sit leval @ 3* to the rearYou don't know what you've got til it's gone
Matt's 1951 Chevy Fleetline- Driver
1967 Ford Falcon- Sold
1930's styled hand built ratrod project
1974 Volkswagen Super Beetle Wolfsburg Edition- sold
-
03-31-2006 05:05 PM #4
CHR Member
- Join Date
- Apr 2004
- Location
- Little Elm
- Car Year, Make, Model: 34 Ford Low Boy w/ZZ430 Clone
- Posts
- 3,890
Yep, the tailshaft of the trans should have about a 3 degree down angle, and that will make the carb flange just about level. Then, the differential yoke should have about a 3 degree up angle.Jack
Gone to Texas
-
03-31-2006 05:41 PM #5
CHR Member/Contributor
- Join Date
- Apr 2005
- Location
- bay city
- Posts
- 10,546
o on the tail shaft leve thru centerline crank to trans run the rear end 3 down any thing will work to a point long as the u jonts are not runing at the same plane . becarefull going up+ on the rear end with wind up will trash the ujoints for sureLast edited by pat mccarthy; 03-31-2006 at 07:00 PM.
-
03-31-2006 06:55 PM #6
CHR Member/Contributor
- Join Date
- Jul 2003
- Location
- Madison
- Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
- Posts
- 21,160
Make sure you have the rest of the car weigt estimated fairly accurately, and mock up some weight for those components, also. Have a couple fat buddies stand on top of the frame and bounce it a few times too....or remove the springs and block it to where your ride height will be prior to setting your engine angle....Yesterday is history, tomorrow is a mystery, Live for Today!
Carroll Shelby
Learning must be difficult for those who already know it all!!!!
-
03-31-2006 08:53 PM #7
CHR Member
- Join Date
- May 2003
- Location
- Zephyrhills, Florida, USA
- Car Year, Make, Model: '32 Henway
- Posts
- 12,423
And it's perfectly ok to move the motor/trans to the passenger side of the vehicle as much as 2 to 3 inches if you have to in order to clear steering or whatever, so long as you keep the crank centerline parallel with the centerline of the car.PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.
-
06-12-2006 06:31 PM #8
CHR Member
- Join Date
- Oct 2005
- Location
- Columbus
- Car Year, Make, Model: 78 F-100 & 85 S10
- Posts
- 206
Good one Denny.Your getting better all the time
Hey has that thing gotta Heme in it? No, it's a shevy not heme!
Reply With Quote
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
I'm happy to see it back up, sure hope it lasts.
Back online