Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Smoke out of dipstic??
          
   
   

Reply To Thread
Results 1 to 4 of 4
  1. #1
    zort86 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Raleigh
    Car Year, Make, Model: 80 CAMMARO
    Posts
    11

    Smoke out of dipstic??

     



    Hey guys, I have been going back and forth this this problem. I have a 1980 Camaro, I have rebuit the engine last year, and I have been having the problem where it will smoke. It will blow bluih smoke when you rev it up. at idle it is fine, or at least you can not see it, but if you rev it up past 3000 rpm, or when you drive it and you step on it it smoes bluish. I say blue ish cause I thought it was white smoke at one point, but at closer inspection of the smoke it dose look blueish.I have rebuilt mostly all the engine, excepte I did not have the block bored or checked. I honed the cylinders with a stone and drill. I replaced the bearings(the crank was no maked at all, and the block looked fine so I just replaced them), I replaced the stock 305cid dish pistons with flat top pistons with moly rings. I also replaced the heads with performance rebuilt heads, and I replace dthe carb.
    Like I said I did not have the block checked out, lake of money, and time. so I am leaning toward two of the cyl are out of round, or cracked. I checked trhe plugs and #3, and #6 plugs are wet with oil. I have taken it on a trip, I moved from NJ to NC, and I drove it down, that was when I really noticed the smoking problem. She ran great, no problems, exept for this smoke. I did a compression check and I am ranging from 115 to 125 psi. I was told that was low, but this is a 305 cid, and if memory searvs me the compression for a 305 in 80 was 120psi, I have to look it up to verify.
    Any way, today I took the car out to check a few things and I noticed that there was smoke coming out of the oil dip stick tube, and out of the hole for the pcv on the pass side, but when I removed the breather on the drivers side there was not smoke coming out of that side. This is driving me crazy. If you have any help or advice would be great, thanks.
    There is not substitue for Cubic Inches.
    Loud exhaust saves lives.

  2. #2
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Could be cylinders out of round, could be bad valve guides, the right way to hone cylinders is with block plates installed on a powerstroke hone machine. To be honest, sounds like you just cut too many corners. Sorry if I hurt your feelings.
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

  3. #3
    zort86 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Raleigh
    Car Year, Make, Model: 80 CAMMARO
    Posts
    11

    Ya I did not cut a lot of courners, but I did cut one, and it was a big one by not sending the block out. I was on a very tight budget. I was thinking the valve guildes, but I will not realy know untill I pull the intake out and look in the heads. I kind of rule out the heads, they have been rebuilt with new guildes and valves, but that doesn't rule it out completly.
    There is not substitue for Cubic Inches.
    Loud exhaust saves lives.

  4. #4
    zort86 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Raleigh
    Car Year, Make, Model: 80 CAMMARO
    Posts
    11

    I thought maybe the seals, since it is not noticable untill it reves up and creates more preasure to pull the oil in. I am goingto have to at least pull the intake to look in the runners to see if the oil is comming down the valves.
    Thanks guys
    There is not substitue for Cubic Inches.
    Loud exhaust saves lives.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink