Printable View
The 305 heads are a lighter weight casting and prone to cracks.Quote:
Originally Posted by 305chevyboi
If you can find them cheap enough I would look into some heavier weight casting's such as 441's or 993's or save you money and buy after-market heads.
ok that a bet
320 Hp @ 5k
361 Ft/Lbs @ 4k
figuring 9.0 compression
I've also seen, just don't remember where it was, there is now a package out to stroke a 305 out to 340... With the right heads and valve train, could be interesting. I've done a couple Ford 347 strokers. They won't run with the 408's, but they do run strong!!!!
How bout some parts and specs for those of us whom have 305s which need to be rebuilt?
I found the last 334 build specs.Quote:
Originally Posted by firebird77clone
Pistons part #KB 186.
Scat crank part #350-3750-5700.
Rod where prepped stock 5.7's with ARP bolts.
Lunati part #301a4LUN.
441' heads with 1.94/1.6 valves.
Edelbrock performer intake.
Edelbrock 500 cfm carb part #EDE1803.
The Camaro had a 3.55 gear with 2,000 stall.
The engine was never on the dyno.
I would guess 275 hp.
Torque was very good.
The car would "light" the tires up under 20 mph very easily.
He also claims he is getting close to 20 mpg if he keeps his foot out of it.
I would guess closer to 17 mpg.
It was a good build.
Yes, you will have to clearance some of the rod bolts.
Thanks Eric, with my recent accumulation of Camaro's, got to save the part info, might be needing it!!!!
I wonder what the dollar per HP ratio is for a stroked 305, there does not seem to be a great gain to be had from doing it.
Unless your are just dying to stroke a 305 and don't care how much it costs, there are much cheaper ways to go about making horse power.
It would seem better judgement to find a cheap 350 and spend the same rebuild money on a 383.
If he already has a 305 block it would be less money plus he already knows what he has and in that aspect it would be cheaper.Quote:
Originally Posted by 41willys
You will get more hp of course out of the 383 for the same dollar amount.
If you are wanting to stroke bore and buy heads pistons rods etc....I would look to the 350 block not the 305.The 305s strong point is cheap and plentiful,once you do the whole nine yards to it you loose the cheap part.At the end of the day you will have spent the same money on way less performance than a 350. Do not get me wrong I like the 305 and have a built one now,but with the money you want to spend it would work out way better to do this to a 350 after all you are only going to use the block from the 305 when its all said and done that will be the only piece you dont replace.Soo for a 100 more you could build a 383 after all you are buying a crank heads rods pistons etc.The value of the 305 is to utilize the crank rods pistons and heads etc you already have to keep the price down.
I would do a intake ,cam and header upgrade to the 305 and call it good,I would not spend all that cash on a 305,because unless you stick your head between the firewall and motor to see casting numbers you will not know its a 305 untill you want to race someone then you will know its a 305:LOL:
The small bore on these blocks makes big hp numbers harder than a 4 inch bore block.Plus you can build the 350 and still drive around,then do the swap in one weekend and be driving again.You are looking at a minimal of 30 days down with machine work and ordering parts for the 305,because you cant really order pistons till the blocks bored and so on with the rest of the build.
Do what you like ,....but you will not be gettin the best value for your dollar and will have to tell everyone its a 305 because it will look just like my 383 that cost the same as your 305 stroker and will smoke your stroker motor big time!!!
You spent 50 bucks on 2 cases of beer and my guy gets me 6 cases for the same price ,...who you gunna want to get beer for ya ?.......:LOL:
Already E-Mailed him what I did on my 305.
I had about $3300 in a 377 (destroked 400). I can promise you your stroked 305 won't touch it in power and wouldn't be much cheaper. Most of that was machine work and aftermarket heads. I ran 11s with a full interior and a wore out 3.73 posi in a 86 monte ss (similar car)
read up on what the bore/stroke ratio and rod length do for power production and how they affect the rpm range its good for
A 377 is great on street if you like very step gears and a loose stall .Quote:
Originally Posted by 53sled
Most people I know that run them run a lot more than a 3.73 gear in the 1/4 mile more like a 4.88/5.13 gear.
11's in the 1/4 mile with a worn out 3.73 posi.
WOW!!! you must be making 650+ to only need a 3.73 in the 1/4 mile and run 11's.
Well, I have a 350 roller cam block for one Camaro. Thinking more like putting a stroked 305 in an S-10 or something. BTW, the 334 stroker kits were available thru Northern for about $400.00. For a little engine, that isn't bad. My only reason for doing it is because (as Erik said) all the parts are laying in the garage.Quote:
Originally Posted by 41willys
If I want to build for horsepower then I guess I'll just get a fresh set of heads for my 514 and go back to laying waste to all the sbc's I run across!!!!!:LOL: :LOL: :LOL:
Got to ask, what is the weight of a fully dressed Monte??? Sure is one heck of a low et for such a lazy gear,,,,,.....Quote:
Originally Posted by 53sled