Thread: Gen V oil pressure issues

Tweet

Originally Posted by gravensg

Tried oil pressure gauge had a mechanical autometer, put an electronic autometer on. That is why I think it is bleeding internally. I cut open a filter and no sign of termoil... It is pissing me off. I have a 454 w/ 150K+ miles on it and pulling a trailer,hotter then hell out the oil never drops below 30 psi at idle.

well were it would or could bleed off is loose rods and main s loose oil pump loose cam . other things like plugs not in block . all things i listed .but the mains and rods i would bet is what going on with this .or your getting the oil so hot its like water and pissing past the mains and rods loose mains and rods will not make it better .i told you i did not hold the 10psi for every 1000 rpms for much .i built many engines .but think about it .if you held your rule 10 psi for 1000 rpms you only need 10 psi for 1000 rpms thats past idle on some engines

engine is not that hot and it has an oil cooler on it. 220 is about as hot as it gets and that is at a stop light after a long run. I guess I will pull the POS out and start digging. I believe it is "Smokey" Henry Yunick's gives the general rule of thumb of 10 psi/1000. I have had some pretty tied engines that build more pressure than this thing, copper on the babbit showing...

If I find something I will take a picture and send it across.

I looked in my 97s' service manual and the main bearing clearance varies with the main cap location. I hope the crank is not F' bombed!

Originally Posted by gravensg

engine is not that hot and it has an oil cooler on it. 220 is about as hot as it gets and that is at a stop light after a long run. I guess I will pull the POS out and start digging. I believe it is "Smokey" Henry Yunick's gives the general rule of thumb of 10 psi/1000. I have had some pretty tied engines that build more pressure than this thing, copper on the babbit showing...

If I find something I will take a picture and send it across.

I looked in my 97s' service manual and the main bearing clearance varies with the main cap location. I hope the crank is not F' bombed!

yep i know who said it as for cap location the rear main comes in a abit bigger they are all the same size on main housing bores.i built many hi hp bbc 450and past 900 hp how i fit the bearings will change abit .i go by the book on crank and housing bore size on stock or on race stuff and thats the small number on housing bore size. if crank needs to be ground we grind it to the size of real bore size with real size bearings TQ in and cut the crank for the size we want or fit the bearings to the size you want to run its not hard to be to big if you do 1/2 ass machine work there is allmost 001 on main housing bore same with rods housing bore size is 0005 by the book spec s now how much will you live by from size to size when you rebuilding a housing bore ? mains or rods? i keep less then 0002 with tapper and no more down from were i want it for size .if your work by the small and big numbers in the book for a housing bore .now add a crank low end of spec with a under size bearing i have seen with my own eyes many time them as much as 0005 from mich .to king to ACl. all this adds up.as a bbc engine builder and a owner of a engine machine shop i do know what works for me and were i will machine housing bores and grind the crank to so i know were i will be about were i want the bottom end to be at

I know the guy knows what he, builder, is doing. He builds circle track motors, engines that have been out on the salt flats, and 1/4 mile stuff and wins or goes damn fast trying.

Just not sure, and disappointed that I tried to spend the cash and just have a tough BB.

do you have bearing preferance? king, Clevite, Child & Albert...

Originally Posted by gravensg

I know the guy knows what he, builder, is doing. He builds circle track motors, engines that have been out on the salt flats, and 1/4 mile stuff and wins or goes damn fast trying.

Just not sure, and disappointed that I tried to spend the cash and just have a tough BB.

do you have bearing preferance? king, Clevite, Child & Albert...

for what stock or race i use .kings.acl. clevite. speedpro s and feds ,some for stockers to mild builds and other hi hp street to race