Is it possible to convert the shift on the column to the floor without replacing the column?
Printable View
Is it possible to convert the shift on the column to the floor without replacing the column?
its a 62 chevy C10 with 383 and TH 350
There should be a roll pin through the shift lever, knock it out and disconnect the linkage and you are ready to go. It does make for a rather ugly steering column though.
".... It does make for a rather ugly steering column though....."
You got that right :3dSMILE: :3dSMILE:
I've seen so many really beautiful cars over the years with the shift nub left on the column (especially 50's/60 era cars). All that work and they leave that little detail.
There are a few choices if it bugs you. Get a column from a floor shift truck and go through the hassel of changing it.
Spend a lot of money and buy and aftermarket column.
Or my favorite ;) take a cut off wheel and cut the nub off, fill the hole with body filler, sand smooth and paint, which can all be done in car.
I don't know about Chevvies, but I used the shifter out of a '66 Mustang in a console I made in my '73 F100. The previous owner had butchered the steering column so I took the collar from a '66 Mustang and modified to fit the F100's column. Looks like it came from the factory that way.
I had a GM tilt column with a shifter on it. I am a pretty handy guy with all things mechanical, so I thought, I should be able to convert this column to no shifter. I took my time, made sketches and took digital pictures as I went along, and disassembled everything. By the time I had it torn apart enought to consider removeing the shift lever I had the biggest damn mess you ever seen, and threw the whole thing out.----My answer is NO unless you do like Mike P suggests and cut it off in the car and fill the hole with playdough.
So if I disconnected the the linkage and remove the roll pin, i could just cut if off and fill it in, sand, and paint?
Brain I was just thinking, 30 yrs. ago while I was working at a caddy-olds. dealer I used to disassemble those steering column and rebuild them. It helped to have the proper tools though. I wouldn't go into one today for no amount of money. :whacked:Quote:
Originally posted by brianrupnow
I had a GM tilt column with a shifter on it. I am a pretty handy guy with all things mechanical, so I thought, I should be able to convert this column to no shifter. I took my time, made sketches and took digital pictures as I went along, and disassembled everything. By the time I had it torn apart enought to consider removeing the shift lever I had the biggest damn mess you ever seen, and threw the whole thing out.----My answer is NO unless you do like Mike P suggests and cut it off in the car and fill the hole with playdough.
Yes you can with that truck. It has a pin in there right next to the column and you pop it out. On my 66 F100 the pin wont come out and there is supposedly some way or no way (I haven't found anyone that knows) to get it out. Mine I just cut of with a sawzaw. Take all your linkage out from the column and buy a new shifter.
Here's what it looks like cut and filled before prime and paint.
here's another one that's already finished, used the same process as the first.
Quote:
Originally posted by Bob Parmenter
here's another one that's already finished, used the same process as the first.
you do pretty work bob. :cool:
Kind words Mike, thank you.Quote:
Originally posted by lt1s10
you do pretty work bob. :cool:
Very nice work---Jeez, if I'd knew it was that easy I'da saved about a zillion dollars on an Ididit tilt unit.
I'll throw this one out for someone's future project.
When I built my 58 Chevy several years ago it had been a 3 on the tree car. As usual, I cut the nub and filled the hole. I built the car with TH350 and used a B&M floor shifter (the kind that looks like a 60's 4 speed shifter).
Instead of also cutting the 2 shift levers off flush at the bottom of the column, I only cut one, and left the one that was spring loaded and would cause the shift collar to rotate.
I welded a short lever to the shift arm on the transmission that would connect back to the shift column with one of the factory 3 spd shift rods. When the transmission was shifted with the floor shifter, the shift collar on the column would rotate. The 58's had an automatic trans shift indicator in the dash (which was filled with a blank on stick cars). I built a custom shift indicator panel (it showed PRND21 instead of PRNDGr), and then the transmission shifted the pointer on the collar would show the correct gear on the dash.
:LOL: well........it's not always as "easy" as it appears.Quote:
Originally posted by brianrupnow
....... if I'd knew it was that easy I'da saved about a zillion dollars on an Ididit tilt unit.
These units are '67 GM midsize (Cutlass, Chevelle, Skylark, Tempest) pieces. I bought quite a few over the years back when before the uptick in muscle car interest. Nowadays you compete with the GTO etc. crowd. I don't remember paying more than $35 for any of them, but they now go for about $150. Finding them with good, tight tilt mechanisms, and signal switch gear is a little tougher. If you have to spend any time/ money rebuilding them then it's back to that special tool and hassle you guys talked about earlier. Then to get them smooth looking they have to be modified to slip into the 2 1/2" dia. length of exhaust tubing with the column drop welded on as shown. '70's GM pickup and van columns are a comparable look alternative and don't need the tubing to clean up the lower column, but these have also been "discovered" so their prices are up and you still have to look to find one that's not too sloppy in the tilt mechanism as well as usually shorten the steering shaft.