Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree8Likes
  • 2 Post By 36 sedan
  • 2 Post By Scooting
  • 1 Post By Dave Severson
  • 2 Post By 34_40

Thread: Leaf Spring Question
          
   
   

Reply To Thread
Results 1 to 11 of 11
  1. #1
    ranchero68/69's Avatar
    ranchero68/69 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2008
    Location
    Winnipeg
    Car Year, Make, Model: 1968 ranchero
    Posts
    13

    Leaf Spring Question

     



    I have a 1968 Ranchero I put new leafs in it and the driver's side sits exactly one inch lower than the passengers side. I would like to reArk the drivers side so it sits level is that something they can do, can they put exactly a one inch lift into the spring when they reArk it. Guess what I am asking is how much of a exact science is rearking leaf springs.
    Bil
    Attached Images
    Just because you're not paranoid doesn't mean they're not out to get you.-Steve earle

  2. #2
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    You need someone who works it in-house, because it is a bit of a hit and miss, and it might take a couple of tries.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

  3. #3
    36 sedan's Avatar
    36 sedan is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2012
    Location
    american canyon
    Car Year, Make, Model: 36 Ford Sedan, 23 T Bucket
    Posts
    1,899

    JMHO, but if you installed new springs, either the springs are incorrect or something is missing/wrong on one side.

    If you set both springs on top of each other and the arc is the same, then something else is wrong. It could be spring tension or a spacer block misplaced. Could even be a mismatched shackle. I would make sure there isn't something wrong with the springs or install before attempting to correct it by arcing springs...
    NTFDAY and cffisher like this.

  4. #4
    Driver50x's Avatar
    Driver50x is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2016
    Location
    Saint Petersburg, Florida
    Posts
    429

    Did it sit level before the spring change? The out of level condition could also be caused by a problem with the front springs.
    Steve

  5. #5
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    My 69 chevelle nomad sat low on drivers side, I did a full spring swap, and it still sat low on driver side, especially when the fuel tank was full, because it is on the drivers side. I ended up shimming the coils on that side.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

  6. #6
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Do you have a spring shop close by you? It isn't so much science as they can apply force to change the arc. but like said above, the front spring can also be causing an issue, the mount at the axle must be the same on both sides as well, check the shackle and bushings are the same on both sides.. HTH

  7. #7
    Scooting's Avatar
    Scooting is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2008
    Location
    Rio Rancho
    Car Year, Make, Model: 1940 Ford Sedan
    Posts
    537

    Like all the replies are saying check everything first. I would think a new set should be the same.
    To answer your question about spring arcs, you need to go to a place that does spring work for heavy duty trucks, dump trucks - Semi trucks. They are the most knowledgeable. I took a 4 wheel drive van in once and a 350 Ford Centurion another time, was looking to raise both with new springs. I gave them the dimension I wanted, measured from the floor to the bottom of the front bumpers for both, 6 inch lift on one - 4 inch on the other. Came back to pick them up and pulled out my tape measure and each time they were exactly on the number on both sides. Not a 1/16 off but exact measurement. Sign of a professional shop that knows what a quality job means to a customer. (and they rode like a charm, not stiff but like a luxury car.)
    Last edited by Scooting; 12-30-2019 at 09:27 PM.
    Dave Severson and Driver50x like this.

  8. #8
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    I'll ask the obvious, but have you driven the Ranchero since replacing the springs? New springs need a few miles on them and some bumps to take their final set. All it takes is one bushing with a bit of a catch in at or even an over tightened bolt to make a vehicle sit high on a corner.
    Driver50x likes this.
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

  9. #9
    BBB
    BBB is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Walton
    Posts
    14

    Could you try switching springs from side to side and see if that changes your ride height?

  10. #10
    34_40's Avatar
    34_40 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    New Bedford
    Car Year, Make, Model: 34 Ford 3W Coupe Replica
    Posts
    14,606

    Since there were no replies since Dec 2019.. I wouldn't expect him to reply now.
    NTFDAY and rspears like this.

  11. #11
    rspears's Avatar
    rspears is online now CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,988

    Quote Originally Posted by 34_40 View Post
    Since there were no replies since Dec 2019.. I wouldn't expect him to reply now.
    ...and since ranchero68/69's last activity was 5 January 2020. Seems he asked a question, got a bunch of good advice/questions and backed away.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink