Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 
Like Tree5Likes
  • 1 Post By chopt50wgn
  • 1 Post By rspears
  • 1 Post By NTFDAY
  • 2 Post By Hotrod46

Thread: voltage drop problem
          
   
   

Reply To Thread
Results 1 to 9 of 9
  1. #1
    oldways is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2003
    Location
    Mossel Bay
    Car Year, Make, Model: 36 chev pickup 63 f250 4X4
    Posts
    39

    My Social Networking

    Follow oldways On Twitter

    voltage drop problem

     



    Hi am building a Austin Healey replica with a Ford V6 motor space is a big problem so the radiator has to tilt at an angle. I have just installed an electric pull fan to help with cooling. The fan draws about 20 amps. I installed a 90 amp alternator. When the fan switches on there is a big voltage drop all the guages register a lower value and the volt meter drops to 10 volt but the charge light stays off so alternator still charging. Any ideas what the problem could be?

    1) battery to small presently 60 ah
    2) bad earth
    3) faulty battery

    If i disconnect the fan everthing returns to normal

  2. #2
    chopt50wgn is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2013
    Location
    Pottstown
    Posts
    169

    When you have an electric fan............you should have a relay between the fan and switch. The relay takes the hit of electricity so the switch does not. Not an electric guru here but know enough to tell you this.
    53 Chevy5 likes this.

  3. #3
    rspears's Avatar
    rspears is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Sep 2007
    Location
    Gardner, KS
    Car Year, Make, Model: '33 HiBoy Coupe, '32 HiBoy Roadster
    Posts
    10,988

    I agree, it sounds like you've got your fan powered from the Accessory Circuit. With a relay, the power comes direct from the battery, with the switch side of the relay the only Accessory load.
    ted dehaan likes this.
    Roger
    Enjoy the little things in life, and you may look back one day and realize that they were really the BIG things.

  4. #4
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,333

    What gauge wire are you using? The lowest I would use is 12 gauge.
    rspears likes this.
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  5. #5
    53 Chevy5's Avatar
    53 Chevy5 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2005
    Location
    Doon, Ia
    Car Year, Make, Model: 53 Chevy 3100
    Posts
    2,708

    I think you need to put a relay in as well. Those fans aren't made to run without one.
    Seth

    God cannot give us a happiness and peace apart from Himself, because it is not there. There is no such thing. C.S.Lewis

  6. #6
    Hotrod46's Avatar
    Hotrod46 is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2007
    Location
    Vidalia
    Car Year, Make, Model: 1946 Ford Coupe, 1962 Austin Healey 3000
    Posts
    1,496

    +1 on the relay. I too am working on an Austin Healey replica (Sebring) and I can say that the original wiring was minimal. As I recall, the main supply to the harness is just 10 gauge wire (maybe 12 gauge) and this has to carry all the loads in the car. As these cars were built mostly back in the 80's and 90's, they were not really wired with electric cooling fans in mind. I will be rewiring mine with my own harness.

    A 20 amp draw with a 90 amp supply shouldn't cause major problems provided the wiring is up to the task.

    Run a separate wire with 30 amp fuse directly from the battery to the switched portion of the relay. This should be 12 gauge at a minimum, 10 gauge would be better to minimize voltage drop. The relay coil would be triggered by whatever switch you are using now. The fan ground would be better if run to the engine block or directly to the battery.

    You didn't say if your car is a new build or a rebuild of an older car. If it's a rebuild, I would recommend that you look at the whole wiring harness carefully. It could have many poor or deteriorated connections in the harness (mine did). There are many street rod wiring harnesses available now that will have better wire, modern fuses and are built with things like fans in mind.
    Mike

    I seldom do anything within the scope of logical reason and calculated cost/benefit, etc-
    I'm following my pass​ion

  7. #7
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    Ditto on the above

    Here's the answer:
    JEGS Performance Products 10560: Electric Fan Wiring Harness & Relay Kit | JEGS

    I can make this up in my garage for about ten bucks, but I have a stash of #10 wire and a bunch of relays. Buy the kit and everything you need is there. Well spent $35.

    Click on the instruction tab and there's a nice picture.
    Glenn
    "Where the people fear the government you have tyranny. Where the government fears the people you have liberty." John Basil Barnhil

  8. #8
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    What brand of 'lectric fan? I have a Cooling Components fan that claims 20 amps at steady state but the fine print says it pulls 70 amps at startup....Learned to read after I toasted a relay.....putting in a much larger capacity relay now.

  9. #9
    firebird77clone's Avatar
    firebird77clone is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Hamilton
    Car Year, Make, Model: 69 nomad, 73 charger, 74 vega
    Posts
    3,900

    I would add that the battery itself is not the best place to source your power for the relay.

    There should be a power junction which the alternator feed wire connects to. This junction is a better source for the relay. It will allow the alternator to better sense the system load.
    .
    Education is expensive. Keep that in mind, and you'll never be terribly upset when a project goes awry.
    EG

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink