Printable View
Can someone gimme the dummy proof way to tighten or adjust the rocker arm studs if i have my intake already on my Trans am. Should they be a certain torque or just tigjh enuff to rstrict the rod from spinning? I did not rotate the crank I adjusted them all at once, Could this be why my engine gets so hot so fast???
I assume that you're asking about rocker arm adjustment. Take a look at this thread, and it'll give you some directions to follow.Quote:
Originally posted by slaisebam
...way to tighten or adjust the rocker arm studs
http://www.clubhotrod.com/forums/sho...ve+adjustments
Dan J
This is a trick question. Your engine won't run if you did what you said you did. It can't get hot if it doesn't run. You should have to replace the bent pushrods and maybe some other bent or broken parts. Then get a Chilton's or Motor's repair manual and try again when you're sober.
I saw this post earlier....... I wasn't going to say anything but.....:confused: :confused:Quote:
Originally posted by The Al Show
This is a trick question. Your engine won't run if you did what you said you did. It can't get hot if it doesn't run. You should have to replace the bent pushrods and maybe some other bent or broken parts. Then get a Chilton's or Motor's repair manual and try again when you're sober.
The Al Show has a point.
Anything is possible on this site Streets. It might even be one of my other identities trying to start something.
These rocker arms wouldn't be part of some sort of exotic "PRE LUBED MONO LEAF" system woooood they??? :whacked: :whacked:
Have patience with me, I'm learnin, but I do know that my engine does run cause I've driven the car since i replaced the head gaskets, and I did tighten my Rocker arm studs the way I described I dont think my rods are bent but I guess i need to check, so whaddya say to that.? thanx for the link DANO!!!!
Are they hydraulics or solids?Quote:
Originally posted by slaisebam
Have patience with me, I'm learnin, but I do know that my engine does run cause I've driven the car since i replaced the head gaskets, and I did tighten my Rocker arm studs the way I described I dont think my rods are bent but I guess i need to check, so whaddya say to that.? thanx for the link DANO!!!!
Being an 88, they would almost have to be hydraulic, wouldnt they?Oh, and streets, if memory serves me right, the oldsmobile engines were a 78 option. Your talking of the 403, I hope. Anyway, if the 403 is like the 403 in my car, they are almost dummy proof. Actually, i think the same design was used on all the small block heads for rocker arms. Wasnt it?:confused::confused::confused::confused:
slaisebam:Quote:
Originally posted by drg84
Being an 88, they would almost have to be hydraulic, wouldnt they?Oh, and streets, if memory serves me right, the oldsmobile engines were a 78 option. Your talking of the 403, I hope. Anyway, if the 403 is like the 403 in my car, they are almost dummy proof. Actually, i think the same design was used on all the small block heads for rocker arms. Wasnt it?:confused::confused::confused::confused:
We need more info. What engine do you have in the Trans Am? And what yr. is it? Hydraulics would be a little more forgiving than solids. But if they were set w/engine not running maybe not, as they would probably just colapse w/o oil pressure. If they have the rocker assembly like Streets posted u just torque em' right?
tryin to upload this pic, anyway its a 305, Performer intake with the edelbrock 600, thats all Ive added besides the head gaskets.......any help on how to upload a pic would be good too......
Click on post reply or quote, scroll down below the text box & you will find a BROWSE button. Load a pic. off your Hard drive. I have best luck with JPG files. Make sure the pic. isn't too big. In photoshop I make them 4.5" wide and they always load fine.Quote:
Originally posted by slaisebam
tryin to upload this pic, anyway its a 305, Performer intake with the edelbrock 600, thats all Ive added besides the head gaskets.......any help on how to upload a pic would be good too......
check it out, nothing special