yep i bet :LOL:Quote:
Originally Posted by billlsbird
Printable View
yep i bet :LOL:Quote:
Originally Posted by billlsbird
I had solid mounts on my panel truck when I was a kid. We drove it all over the country (pulling a camper) and never had any issues. When guys would see them at a rod run they would tell me "they're gonna' break" . never did. :whacked:
http://img5.glowfoto.com/images/2008...429532194T.jpg
aren,t we all still kids :3dSMILE: i am 44 and still have soild mounts i am happy to know i am still young :whacked: i have rubber mounts there called front tires :DQuote:
Originally Posted by pro70z28
Quote:
Originally Posted by billlsbird
I did THAT??? Huh, I don't even remember doing that. The worst part is, I know zip about cams. :eek: :LOL: Musta been someone else. :rolleyes: :)
Don
Quote:
Originally Posted by Itoldyouso
No kidding!!!! Don't forget one of those little hoist things to put your wheelchair in the back!!!!!!!:LOL: :LOL: :LOL:
.....Well Solid Mounts it is. Mainly because of a lack of space issue. Lots of room on the passenger side but the steering box is right under the motor mount on the drivers side. I will post some pic's but I seriously doubt that there is room for anything but solid motor mounts. I re-worked the pre made hemi motor mounts that I had to get them to work on the drivers side And I used a Suspension Engineering Urethan mount for the transmission...... BUT someone told me that with solid mounts you will break the mounting points off of your block? I hope their wrong because 392 blocks don't grow on trees!!! Bill
Mine has solid mounts.. It's a 440 with elephant ears.. I never do any long trips either..Solid mounts do add rigidity to the chassis, for what it's worth.
I have built my "A" with solid mounts. Also open wheels and no hood, if I want. It is like a celebration of all things mechanical. I want to see the tires, suspension, steering and pulleys, feel the engine, shift the gears, all of it. Might change after a bit but that remains to be seen.
Thanks Daffy & Willowbilly, then I'll be ok, I just don't want to ruin my block. The block was the main thing that made my decission to go with Big Al's motor! 392 blocks are hard to find!!! The shack, rattle & roll won't bother me!!! I love that!!! ;) Bill
If you are worried about the block, make some sort of mid mounts too. Like come off a couple of the bell housing bots on each side. That was my original plan when I had a 429, front, center and rear solid mounts. Kinda like a Vincent bike, the engine acts like part of the frame. I have no crossmember between the front one where the spring mounts and the one under the tranny.
....Good idea Willowbilly! I'm going to go out to garage & see how that would work! Thank You! ;) Bill
The ol' motor plate mid plate would fix it. (You'd need to redo the converter spacing to the flex plate).
http://img.photobucket.com/albums/v2...s3-30-05-7.jpg
http://img.photobucket.com/albums/v2...e3-26-05-3.jpg
http://img.photobucket.com/albums/v2...e3-26-05-4.jpg
http://img.photobucket.com/albums/v2...aro2-15-06.jpg
http://img.photobucket.com/albums/v2...arofront06.jpg
...Thanks Pro! I wish i had the equipment & knowledge to do this! Bill
it is not hard the cut alum and you do not need much tools make a template out of cardboard then lay it out on you alum then out can cut a out with a variable speed jigsaw with the right saw blade .i know a guy that cuts thick 7075 t6 with his table saw with a carbide tipped blade and some WD 40 BUT you need to watch out for the flying hot chunks of alumQuote:
Originally Posted by billlsbird
That's true. I went down to the salvage yard & picked up 3/4" aluminum plate for the "Z". They had a 4'x10' sheet & said I could have however much I wanted but, they said they had no way to cut it. I used a carbide blade in a skil saw, str8 edge & a couple clamps a lopped off a chunk O' aluminum in no time.