Search:
Type: Posts; User: lt1s10
Search:
Search took 0.38 seconds.
-
07-28-2005 06:21 AM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
now thats a new one NTFDAY. :HMMM:
now thats a new one NTFDAY. :HMMM:
-
07-24-2005 06:25 AM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
dont know about the rest, but my bill is in the...
dont know about the rest, but my bill is in the mail. boat labor ant cheap. :LOL: :cool: just joking!!! glade the starter fixed it, but you need to replace the gaskets before you run it anymore.
-
07-22-2005 05:58 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
CaneBreak is there some way you could loosen the...
CaneBreak is there some way you could loosen the starter up after you start the motor and pull it away from the motor and see if the noise goes away, or shim it out some with the washers just to try...
-
07-22-2005 01:15 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
there is a spring in the starter that should push...
there is a spring in the starter that should push the bendix back, take the starter off and see if the bendix will slide on the starter shaft freely it shouldnt.
-
07-22-2005 12:45 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
when the motor starts, the flywheel is supposed...
when the motor starts, the flywheel is supposed to help sling the bendex out of the flywheel not pull it in. if it is pulling it in, then the spring that's supposed to help keep it out of the...
-
07-22-2005 11:46 AM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
where is the starter sol. on the starter or...
where is the starter sol. on the starter or firewall ? do you have just 1 big 12v cable going to the starter?
-
07-15-2005 06:24 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
good luck :cool:
good luck :cool:
-
07-15-2005 06:07 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
i guess i take to much for granted, but the...
i guess i take to much for granted, but the right side of a motor or car is sitting in the drivers seat looking out forward. anything on the passenger side is the right side, standing behind the...
-
07-15-2005 11:00 AM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
i still stand by my quote. :HMMM:
i still stand by my quote. :HMMM:
-
07-09-2005 02:46 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
im not sure on the boat so im not the one to tell...
im not sure on the boat so im not the one to tell you what the advanced timing should be and when it should come in im sure its dif for a boat. somebody on here must know though,
-
07-09-2005 02:14 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
i just saw where you said you could make it stop...
i just saw where you said you could make it stop poping that good, but you need to set the idle with the idle screws not the dist, you need to set the timing with a light and leave that alone.
-
07-09-2005 02:09 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
if you got fire, poping or spitting out of...
if you got fire, poping or spitting out of anything then you either got the valves opening or the dist. firing at the wromg time. assuming your cam is timed right, your valves adj. properly then the...
-
07-09-2005 12:58 PM
Thread: Need some timing advice
by lt1s10- Replies
- 54
- Views
- 8,454
sounds like you might have some wires crossed...
sounds like you might have some wires crossed also, you need to go back and check that to,
Results 1 to 13 of 13
And just because... here is a clip. https://www.youtube.com/shorts/fIrT_uNxPrc
the Official CHR joke page duel