Does anyone know of someone who sells engine test stands or have one they wish to sell ?
Thanks:)
Printable View
Does anyone know of someone who sells engine test stands or have one they wish to sell ?
Thanks:)
Funny you should mention this just as I am looking at an ad for engine stands by Cummins Industrial Tools: $29.99 to hold 750 pounds and another to hold 1250 pounds for $49.99. It seems to me there are many other places which offer similar items such as Auto Zone, Advanced Auto, Sears etc. The Cummins store has a web site at:
www.cumminstools.com
Don Shillady
Retired Scientist/teen rodder
Probabbly be able to modify 1 of those assembly stands to be able to run the motor. Seems all you would need to do is mount an extesion on the front to accomadate a radiator, then put an ignition start switch and kill switch on a panal up higher than the motor welded to the frame. May even be able to weld 2 walmart floor jacks to the outside frame sides ( supports also ) and connect the 2 hydraclic jack arms togther with some kinda linkage so you could set it on the ground for testing and jack it up for moving.
I had designed one last year that was based off of an engine stand. I will see if I can find the drawings again or make new ones for you, if you want.
A dyno would work nice. :) :) :) :) :) :LOL:Quote:
Originally posted by rocknrod
Does anyone know of someone who sells engine test stands or have one they wish to sell ?
Thanks:)
Lil' expensive maybe.:whacked:
I fired my last small block and tested it on a assembly stand that was real beefy. I braced the bottom of the engine with skids and mounted a rad in front on a stand. I started it by arcing the starter. Very simple... the stand was an aviation stand, very large and flips the engine over with a crank so it's real nice to use. It was meant for big diesel engines so I figured no problem....When i cracked the throttle with the open long tube headers on that stand it was pure satisfaction....especially to see it twist that stand like it was cardboard.
Now THOSE are engine test stands ! "Thanks" big guy.Quote:
Originally posted by Streets
There is a difference betwixt engine stands and engine test stands.. Engine stands are where you only assemble the engines..
Engine test stands are where you actually "Run-in" the engine. the test stand can also double as an "assembly stand" whereby the engine stand can't..
http://www.mightymount.com/
http://www.hotrodparts.com/chev.htm
http://www.hotrodparts.com/cad500.htm
"TEST" Stand below...
Also, using an engine stand could work. I just did not want to
get a welder involved (since I dont own one).
Thanks again.
I stand corrected on the difference between an engine stand and an engine test stand, BUT I got a lot of ideas. I was wondering how to keep the engine from going "dry" while I assemble the body. Spinning the oil pump every so often will probably keep the bearing surfaces oiled, but I want to keep the cylinder walls lubricated as well so the idea I got from this thread is to get the radiator installed ASAP and then my rolling chassis can be my engine test stand and I should be able to run the engine every month or so; expecially since there is no drive shaft yet. Thanks!
Don Shillady
Retired Scientist/teen rodder
I kinda' like the plan of buildin' the engine "after" the car is built. ;)
On the other hand I kind'a like the idea of installing the body after the connections are worked out standing over the chassis rather than the time-honored work under the body AND (!) I can chunk out the cost of individual parts and install them piecemeal compared to a large piece of change all at once for the 'glass body. Anyhow, I just thought I can use the chassis as a test stand and save time. I have to study the break-in procedure and WHY NOT go through the break-in with only the trans without the drive shaft? I just know I need to lube the cam with the right stuff, use good oil and change the oil after the break-in. I let you guys heckle me because I really have not worked on a SBC before and I do have a lot of questions, but this is certainly not the first engine I have rebuilt and the general procedures should be the same. I am merely pointing out that you might as well use the chassis as the engine test stand if the body is not there yet.
Over the years I have seen many other rods built as rolling chassis in several car magazines; it looks like one way which works to me!
Don Shillady
Retired Scientist/teen rodder
The 350 tans. might leak tranny fliud w/o a yoke in the tailshaft to stop it? Maybe you could put the driveshaft in and build a saddle for the rear end to keep the rear wheels just off the floor. ( Somethin' more stable than just jack stands). Then you could run it in park and/or drive to run everything.Quote:
Originally posted by Don Shillady
WHY NOT go through the break-in with only the trans without the drive shaft?
How about hooking it all up like Pro said then tie a string or somthing to the carb linkage then find a way to steer it, you could drive it around and terrorize your naighbors if you live in the boonies.
The Vega box and cross steering is already there, Yee Haa!
Don Shillady
To get back to the original question you might want to take a look at this discussion: http://www.hotrodders.com/t42339.html
Restorod is right, that is a slick TEST stand. To answer Streets, I can't see putting that much effort into a stand-alone test stand when I have only so much time to get my car together. Maybe for a shop which will use the stand for many engines that would be a good idea, but I am trying to follow what I have seen in Rod magazines for many years, build a rolling chassis, test the engine in the chassis and then fit the body. I can only say that my Financial V.P. (wife) will very likely not accept an unfinished car so that is pressure from another source to get the car totally finished and I was just kidding about the "Yee Hah!", I do not plan to run the car without the body, although I do have a long driveway!
Don Shillady
Retired Scientist/teen rodder