Painting Pearl, I'll word this a little different

[sgo70]

Okay I'm trying to get this type of paint job but I don't really know where to start except searching the internet and I've done a lot of that!

I was wondering if a pearl paint coat with a flattened clear is too hard for me to get right. Also what brand of paint would be the best for a novice like myself to try and do this with. I've found a close match with Hot Rod Flatz but I wonder if it's any good.

I'm not even sure if this is a pearl paint coat .

Sean

[HOTRODPAINT]

Without seeing it up close, I can't tell if it's pearl or just the hazy look of a flat clear. Could also be a metallic red with a flat clear.

[SprayTech]

Not my thing really , an awful lot of money spent for a non shiny paint job .
That truck I think would be outstanding with shiny clear
But what ever floats your boat and its your money and hotrod

Looks to me like a pearl over the red with a slightly flattened clear coat , but like HRP said with out seeing it with the naked eye its hard to tell .

[sgo70]

Thanks guys,
I have a gallon of pre mixed Sherwin Williams ultra 700 in a red that matched the new Audi A4, not sure what it is exactly, like in this pic. You'll probably like it better Spraytech . Maybe I'll see how it goes on and I guess I could always add some flattener to the clearcoat, maybe????

Sean

[mrmustang]

Thanks guys,
I have a gallon of pre mixed Sherwin Williams ultra 700 in a red that matched the new Audi A4, not sure what it is exactly, like in this pic. You'll probably like it better Spraytech . Maybe I'll see how it goes on and I guess I could always add some flettener to the clearcoat, maybe????

Sean

Sean,

You mean Ultra 7000, as for the clearcoat and flattening agent, might I suggest a series of spray out cards (ie: test panels) be done so that you get the right end results to match your desired final look. Keep in mind that the flattening agent will continue to work for a few hours after the clear has flashed and dried to the touch.


Bill S.

[sgo70]

Oh yea 7000 .

Sounds like a good idea. Who knows I might like it shiney anyways.

Sean

[mrmustang]

The pearl coat will be part of the base coat, not the clear coat put on top of the base. As for flattening the shine, yes, the big three (Dupont, PPG, Sherwin Williams) all offer a flattening agent that is used in the clear coat to soften the shine............


Bill S.

[like2gofast]

Excuse me, but I was wondering if you have yet to discover the formula (if you will) to the paint job in this thread. I really like that look!
If not. I would hate to loose out on the trick(s), so if it's not too much to ask I'd like to see you keep this thread open? Just in case you were thinking of closing it.

Thanks

[mrmustang]

Excuse me, but I was wondering if you have yet to discover the formula (if you will) to the paint job in this thread. I really like that look!
If not. I would hate to loose out on the trick(s), so if it's not too much to ask I'd like to see you keep this thread open? Just in case you were thinking of closing it.

Thanks

There really is no set formula for this, what needs to take place is a series of spray out cards on the day of the actual shoot. Flattening agent will be mixed with the clear coat (not the base) proportionate to what the temperature of the day is (unless you have a proper temperature and humidity controlled paint booth), and humidity levels are. My suggestion is to start at a 4:1 mix of base:flattening agent and do a series of sprayout cards over your base coat to see which end result you like best. Once you have come up with the final product you think looks best, you can then use that formula to duplicate the results on a larger scale.


Bill S.

[cnile64]

have you looked at Hot Rod Flatz paints? they have pearl and metalic flatz

[maxxmuscle]

I've had limited success with flattening clear. Most manufacturers will tell you NOT to do it. PPG for one. I did a bike awhile back, used a 4:1 mix and it didn't flatten hardly any (waiting 45 min between coats), used a 3:1 and it went somewhat, but not near enough, so I mixed a 2:1. Within about 5 minutes it was dead flat! Within 15 minutes, it was turning grey and cracking all over!!! Totally ruined the job and we had to take it all back down and start over $$$$$! AND, something about it, I'm guessing the parafins in it, makes it HORRIBLY hard to sand!!! Stuff is like a rock! Did a 32 couple a couple of weeks ago, started with a 3:1 mix and it didn't flatten enough, so being scared of what happened the last time, I did a 2-1/2:1 mix. Worked like a charm, but I ran out with just the rear quarter and deck lid left (2nd coat). Mixed another batch, 2-1/2:1 and sprayed it on the quarter and decklid and guess what, NO MATCH, didn't flatten enough... !!! . We sanded the whole car down the next day, went back to PPG (using all PPG products by the way) and bought their "Flex and Flat" clear set up. Its kind of expensive, but I will NEVER mix my own flat clear again!!!! The biggest problem seems to be inconsistancy of the flat. PLUS, if you ever have to go back and repair something, you probably WON'T get a match... Check out the Flex and Flat, or something pre-flattened, its a life saver!! Donny

[mrmustang]

I've had limited success with flattening clear. Most manufacturers will tell you NOT to do it. PPG for one. I did a bike awhile back, used a 4:1 mix and it didn't flatten hardly any (waiting 45 min between coats), used a 3:1 and it went somewhat, but not near enough, so I mixed a 2:1. Within about 5 minutes it was dead flat! Within 15 minutes, it was turning grey and cracking all over!!! Totally ruined the job and we had to take it all back down and start over $$$$$! AND, something about it, I'm guessing the parafins in it, makes it HORRIBLY hard to sand!!! Stuff is like a rock! Did a 32 couple a couple of weeks ago, started with a 3:1 mix and it didn't flatten enough, so being scared of what happened the last time, I did a 2-1/2:1 mix. Worked like a charm, but I ran out with just the rear quarter and deck lid left (2nd coat). Mixed another batch, 2-1/2:1 and sprayed it on the quarter and decklid and guess what, NO MATCH, didn't flatten enough... !!! . We sanded the whole car down the next day, went back to PPG (using all PPG products by the way) and bought their "Flex and Flat" clear set up. Its kind of expensive, but I will NEVER mix my own flat clear again!!!! The biggest problem seems to be inconsistancy of the flat. PLUS, if you ever have to go back and repair something, you probably WON'T get a match... Check out the Flex and Flat, or something pre-flattened, its a life saver!! Donny

Donny,

What you have to realize is that when you spray anything with a flattening agent mixed in, it takes 2-4 hours for the car for the flattener to stop it's chemical reaction (even though the paint might be dry from baking it in the booth). I've had a bunch of customers try it on their own, not one of them was patient enough to spray it and walk away for the day. Each one of them ended up at my production paint shop......Patience in the key word here. 4:1 for a start, 3:1 next, 2:1 if you want it to look like colored primer, never 1:1, I REPEAT, NEVER 1:1!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Also, never mix one product line with another, no matter what your paint supply shop tells you. Stick with all Sherwin Williams (or PPG, Dupont, etc) products and use those spray out cards to experiment before you lay one gram of paint on the car/truck/bike/toaster you plan to paint.......


Bill S.