Thread: Front Engine V8 Bug Volksrod Build

Tweet

This project has been on hold for a while...finally getting back to it!

[IMG]IMAG0497 by Ben Modified, on Flickr[/IMG]

[IMG]20141216_164959 by Ben Modified, on Flickr[/IMG]

[IMG]20160713_164753 by Ben Modified, on Flickr[/IMG]

[IMG]20160720_152426 by Ben Modified, on Flickr[/IMG]

[IMG]20160815_150838 by Ben Modified, on Flickr[/IMG]

The Build, to date, is here:

https://www.youtube.com/playlist?lis...h8VZOV52aD9irG

I had a HO racecar / slotcar in that same style..... it had a "wheelie kit" where the conductors were hinged to allow the front to lift.

AHHhhhh... the good ol' days! LOL..

What was the final wheelbase?

.

About 2 1/2.. maybe 3 inches if I remember right!

I dig it.
Didn't think I'd like is when he started.
Reminds me of Roth.

Very nice work on the bug! I like the trans swap too!

Started fitting the driveshaft tunnel, checking bench seat clearance. Had to air hammer off some left over spot welded floor.

[IMG]20160823_161531 by Ben Modified, on Flickr[/IMG]

[IMG]20160823_164337 by Ben Modified, on Flickr[/IMG]

Also cut out a large rust hole and welded in a new panel.

[IMG]20160824_171433 by Ben Modified, on Flickr[/IMG]

[IMG]20160824_171706 by Ben Modified, on Flickr[/IMG]

http://www.BenModified.com

Welded in the driveshaft tunnel today along with more rust repairs

[IMG]20160825_091223 by Ben Modified, on Flickr[/IMG]

[IMG]20160825_091700 by Ben Modified, on Flickr[/IMG]

http://www.BenModified.com

Part 15 is posted on YouTube

https://www.youtube.com/watch?v=ln9XR4VGtv8

Great work!

Times 2! I like this one better than the "van"..

Started on the rust repair at the bottom of the drivers door. Made up a template and transferred it to metal. Still rough, but getting there.

[IMG]20160904_115242 by Ben Modified, on Flickr[/IMG]

[IMG]20160904_125434 by Ben Modified, on Flickr[/IMG]

[IMG]20160904_125321 by Ben Modified, on Flickr[/IMG]

Started on the inner door replacement sheet metal. Cut out the old and shaped a new piece with a piece of threaded rod and flat stock

[IMG]20160904_130512 by Ben Modified, on Flickr[/IMG]

[IMG]20160906_093837 by Ben Modified, on Flickr[/IMG]

The old piece as a template, the new metal and threaded rod

[IMG]20160906_093839 by Ben Modified, on Flickr[/IMG]

Shaping the new metal

[IMG]20160906_095356 by Ben Modified, on Flickr[/IMG]

[IMG]20160906_095850 by Ben Modified, on Flickr[/IMG]

Making the shape more square like the original

[IMG]20160906_101151 by Ben Modified, on Flickr[/IMG]

[IMG]20160906_101229 by Ben Modified, on Flickr[/IMG]

[IMG]20160906_101331 by Ben Modified, on Flickr[/IMG]

New inner in place

[IMG]20160906_112402 by Ben Modified, on Flickr[/IMG]

[IMG]20160906_112444 by Ben Modified, on Flickr[/IMG]

Every thing welded in. Just need a skim coat of body filler on the outside

[IMG]20160906_173834 by Ben Modified, on Flickr[/IMG]

Just needs a skim coat of body filler and a couple of drain holes at the bottom

[IMG]20160906_173923 by Ben Modified, on Flickr[/IMG]

http://www.BenModified.com

Door is done

[IMG]20160907_162707 by Ben Modified, on Flickr[/IMG]

http://www.BenModified.com

Great work on that door!

Originally Posted by 40FordDeluxe

Great work on that door!

Thanks! It only took most of the day and 3/4 of a gallon of body filler....most of which wound up on the floor after hours of sanding. Good learning experience I suppose!

Rust repairs on both doors are complete. Re-installed them this morning

[IMG]20160911_100332 by Ben Modified, on Flickr[/IMG]

Prior to removing the doors, I drilled a small hole thru the hinges, the body and the backing plates to make re-assembly and alignment easier. It worked very well, I was able to re-install the doors by myself with the help of a floor jack and a couple of drill bits. I tightened them down and they shut properly on the first try!

[IMG]20160911_091623 by Ben Modified, on Flickr[/IMG]

[IMG]20160911_120029 by Ben Modified, on Flickr[/IMG]

http://www.BenModified.com