-
55/58 Chevy truck build
-
-
-
-
-
-
These are 1998 Dodge Intrepid seat. I paid 120 for them at pull your part. Can you believe they charged me 10 bucks more because one was electric (driver side electric, passenger manual)?lol Then he looked at me like I was going to put them back over 10 bucks.lol I can tell you one thing there is only junk at the yards near my house now. You can tell all the hotrodders have been through there.lol
I like them because my cab is a big window and I really don't like seeing seats sticking up through the rear window so I knew I needed something with a low back and these fit the bill.
http://farm6.static.flickr.com/5204/...6489364d60.jpg
I then had to modify the mount to from this to this.
http://farm6.static.flickr.com/5202/...fcfd0711ba.jpg
http://farm6.static.flickr.com/5010/...f78ab1706d.jpg
http://farm6.static.flickr.com/5130/...73fe8f3685.jpg
Here are a couple of shot of the seats installed.
http://farm6.static.flickr.com/5249/...d8fa9b5b5a.jpg
http://farm6.static.flickr.com/5246/...2443f3b817.jpg
http://farm6.static.flickr.com/5244/...0465347c0e.jpg
-
-
After buying a flaming river column and installing the column in my truck I thought it was too long. I just did not like how far it was sticking out the firewall. I thought I could live with it but I couldn't take it anymore, so I decided to cut it up. It was much easier than I thought.
First I marked where I wanted the column to stop while it was in the truck. The tape line is where it will be cut.
http://farm6.static.flickr.com/5140/...f4d656b1fe.jpg
I looked down the DD end when I took it out the truck and notice that the DD goes all the way down the column oh now this is easy. The bottom bushing seems to be held in by two dimples so I drilled them out. I can get the bushing out later.
http://farm6.static.flickr.com/5177/...06846f62ed.jpg
I used a cut off wheel to shorten the tube. When I mark the spot with the tape I used a square to mark the cut line all around the radius of the tube and then taped it so that my cut was square.
http://farm6.static.flickr.com/5095/...e297f54761.jpg
I removed the bushing using a vise and two hammers.
http://farm6.static.flickr.com/5257/...455a69544d.jpg
http://farm6.static.flickr.com/5091/...4d5d293dc0.jpg
I then used a hand file to smooth the edges of the cut and install the bushing and cut the DD at the correct length and I’m done. This is easy and I thought someone may need to do the same thing so I posted it.
http://farm6.static.flickr.com/5171/...21e53655c0.jpg
http://farm6.static.flickr.com/5092/...bc8bb9e61c.jpg
I think I like it better now.
http://farm6.static.flickr.com/5258/...7f5758b322.jpg
I was completely shocked at how easy this was it took all of 30 min and most of that was measuring. I've done other columns and its no where near this easy that's why I was dreading do it. What a waste of stress.lol
I fabricated a piece for the interior cab corner were trash can collect. I don't know why GM left this open like this, I guess it was a nice storage area back in the day.
http://farm6.static.flickr.com/5221/...919c539e94.jpg
http://farm6.static.flickr.com/5063/...ecf2c3dcce.jpg
http://farm6.static.flickr.com/5222/...94ac9c7a86.jpg
-
-
You can never have enough good fenders. I had a mess up fender laying around and a new repoped fender that someone gave me. The repop fender fitment was horrible so I decided to use it as a patch panel. I have a passenger fender that I already primed but when I checked the fitment I like the mess up fender a little better. So I decided to fix the fender and use which ever one I like the best when I put the truck back together. Or I just used it as an excuse to weld something together.lol
http://farm8.staticflickr.com/7149/6...15fa6949c1.jpg
http://farm8.staticflickr.com/7167/6...789632dc2d.jpg
http://farm8.staticflickr.com/7162/6...db3901dd41.jpg
http://farm8.staticflickr.com/7014/6...be87a604e1.jpg
http://farm8.staticflickr.com/7150/6...59ced3093a.jpg
This is what is left of a new fender that I used for patch panels because the fitment was so bad. I used the rear for another fender for a buddy. It still has some use so I will not throw it out. It still has a good brace, eyebrow, and front and top panel. Somebody may need a piece of it so I will keep it. I know too many hotrodders to throw it out. I don't know about the other new fenders, but the fitment for this one was garbage.
http://farm8.staticflickr.com/7164/6...6653949c63.jpg
Here is the fender after metal finishing.
http://farm8.staticflickr.com/7160/6...6b902651f8.jpg
I'm still blocking the fenders. They are coming out nice the are pretty straight. He is a pic of them in primer (just because I have not shared in a while) I will be blocking them more but for now I'm moving on to the hood.lol
http://farm8.staticflickr.com/7238/7...8183b30d60.jpg
http://farm8.staticflickr.com/7182/6...9f2fceaa55.jpg
I made it out of 1 inch wide and 1/4 thick flat stock. Making it flow with the radius of the side of the hood took some thought but it came out decent.
Oh yeah I also spot welded the hood to the brace in several spots.
http://farm8.staticflickr.com/7176/6...e08daa7e3a.jpg
http://farm8.staticflickr.com/7036/7...1c8b28b083.jpg
I got the sectioned hood in primer. It was a lot of hammer and dolly work but here it is.
http://farm8.staticflickr.com/7092/7...ebe57d3271.jpg
http://farm8.staticflickr.com/7082/7...8fb49351c6.jpg
http://farm6.staticflickr.com/5280/6...08f7f7f872.jpg
http://farm6.staticflickr.com/5328/7...4a81d0e4fd.jpg
-
Well I decided to start getting the rear fenders ready for primer. I wanted to use these for the truck because they were giving to me by a buddy who bought new ones and he has passed away (He knew they were rough but did not want to throw them away). So I wanted something of his on the truck, so I went to through the trouble of saving them. My question is do you know what evils lives under your primer.
http://farm9.staticflickr.com/8157/6...ddefcc30da.jpg
http://farm8.staticflickr.com/7081/6...8ab42f9b11.jpg
This is what I had to cut away. Yikes
http://farm8.staticflickr.com/7083/7...9e0811fae8.jpg
Remember those repop fenders that I told you I like keeping just incase? Well they provided the majority of the patch panel. A little tweaking and they worked fine. That little rust spot that was left I just formed my hand.
http://farm9.staticflickr.com/8027/7...048b8e4a51.jpg
And here it is, almost ready for primer a little more welding and hammer and dolly work to do and very little filler will be needed now.lol
http://farm8.staticflickr.com/7224/7...431eef50c1.jpg
http://farm8.staticflickr.com/7275/6...c785e2ddc0.jpg
-
Over the years this truck was really used. Man this fender has dents and digs all alone the top area. I used a big red marker to color in the top which I will block sand to see the highs and lows.
http://farm9.staticflickr.com/8009/7...872ea9ffef.jpg
Weapons of choice
http://farm8.staticflickr.com/7040/7...cefca88e20.jpg
I also made this slapper and find it does a great job.
http://farm8.staticflickr.com/7218/7...5f045b42d7.jpg
On the back side you must choose a dolly that is very close to the contour of the sheet metal.
http://farm8.staticflickr.com/7105/7...2ff04b3fa7.jpg
After sanding here is what I had
http://farm8.staticflickr.com/7263/7...19068e02bd.jpg
After the first use of my slapper and dolly I sanded again and here what I have. As you can see the low area is getting smaller. Sanding between hammer and dolly work shows me were I need to concentrate.
http://farm6.staticflickr.com/5337/7...3ecf1c6026.jpg
Worked some more and sanded and had this.
http://farm9.staticflickr.com/8146/7...a8c639119a.jpg
Here what I accomplished the first day, still a lot of work to do but a fender that most would have trashed or covered with way too much filler will be used with very little filler when done. After I remove all the major of the dents I will red marker again and try to fix all the imperfections. All the red markets that are left need to be worked but as you can see there is a world of difference.
http://farm8.staticflickr.com/7246/7...f73127cd05.jpg
It just takes patience and work.
I also wanted to share why I enjoy tig welding sheetmetal. I used a 3/32 2% ceriated tungsten and 1/16 filler rod and tried to keep the smallest HAZ I could. Tig sheetmetal is great you can see how low the bead profile is and some of the metal finishing I started. Man you can hammer and dolly that HAZ to your hearts desire.
http://farm8.staticflickr.com/7109/7...e99204b06a.jpg
http://farm8.staticflickr.com/7188/7...95c18da1b2.jpg
http://farm9.staticflickr.com/8165/7...f79628b590.jpg
-
These are the wheels I ordered for the truck
http://farm8.staticflickr.com/7222/7...4f2df452e6.jpg
http://farm9.staticflickr.com/8167/7...9eaa348ec6.jpg
I guess I can live with a 5 inch lip on the rear wheel, I did want more but they would not give it to me.lol
http://farm8.staticflickr.com/7212/7...34b6a9cf1e.jpg
http://farm9.staticflickr.com/8023/7...925e658f53.jpg
I just wanted to share my experience with Raptor Liner with you guys. Its my first time using this product and I must say I really like it. Its very easy to use and sprays great and was exactly what I was looking for. It dries fairly fast and looks good. I used it on the floor and the bottom of the toe board. It seams very durable so for people looking for something like this you can't beat it. I bought the 4 bottle kit, it comes with the hardener and the gun. I got mine on ebay.
I will also be spraying it on the interior floor.
http://farm9.staticflickr.com/8283/7...c3cd891bd3.jpg
http://farm9.staticflickr.com/8431/7...8a49cc861a.jpg
Well, not really much to report other than I mocked up the hydroboost unit and plumbed the brake lines.
http://farm9.staticflickr.com/8297/8...f1a090a9a9.jpg
http://farm9.staticflickr.com/8033/8...12bf93690f.jpg
http://farm9.staticflickr.com/8460/8...5287538661.jpg
http://farm9.staticflickr.com/8317/8...826b1093c6.jpg
http://farm9.staticflickr.com/8042/8...74c5a7f4d7.jpg
http://farm9.staticflickr.com/8460/8...df060a1a87.jpg
The morning dew makes the painted frame a not look good in the pic. But the paint is smooth and nice. I used Kustom Shop's epoxy primer and satin black. It sprayed really nice. So for anyone looking for some Satin black and epoxy primer for their frame this may be the ticket. It really was not expensive and you will have enough left to do your suspension parts also.
-
Slowly I turn, step by step, inch by inch.lol Well thats how I doing it.
I know its over kill but I base coat cleared the gas tank just because. No other reason.
http://farm9.staticflickr.com/8201/8...a64389f4ec.jpg
http://farm9.staticflickr.com/8203/8...97b26ac3c2.jpg
Here is the tank installed between the frame rails.
http://farm9.staticflickr.com/8342/8...f4efe5e59b.jpg
http://farm8.staticflickr.com/7264/8...d981c74d4d.jpg
Corvette filter/regulator installed
http://farm9.staticflickr.com/8503/8...b060101cc9.jpg
http://farm9.staticflickr.com/8220/8...4e92a30515.jpg
Modified the tank a little for the in-tank fuel pump and lines.
http://farm9.staticflickr.com/8326/8...a5b5dca1df.jpg
Well since I have not posted pics in a while I thought I should no matter how small the mod is. I knew I had to raise my bed floor 2 inches due to my c-notches. I was looking in metal yard for some scrape tubing and I could not find anything I liked, I decided to make my own 2 inch spacers. I try to keep things simple it makes life easier, but of course I will have to move the angle strips on the bed up 2 inches so that bed sits in the same spot as factory.
I will use the bolt to hold the washers in place and then weld it together.
http://farm9.staticflickr.com/8244/8...7e2c1619d6.jpg
http://farm9.staticflickr.com/8370/8...e2006b7bf4.jpg
Here is one of the spacers completed. I will need six of them for the three cross sills.
http://farm9.staticflickr.com/8511/8...935712b4df.jpg
Eventually they will be welded to the frame as a mount for the cross sills.
Here are some misc pics of the 4 link reinstalled with the fuel and brake lines.
http://farm9.staticflickr.com/8384/8...bd94c85d1d.jpg
http://farm9.staticflickr.com/8522/8...fff7964e6d.jpg
I decided to go ahead and weld the bed floor spacers to the frame.
http://farm9.staticflickr.com/8232/8...f8bbe45f61.jpg
http://farm9.staticflickr.com/8089/8...1e291d9a11.jpg
Just checking cross sill bolt alignment.
http://farm9.staticflickr.com/8385/8...94c328e3e2.jpg
Finished and repainted.
http://farm9.staticflickr.com/8518/8...ecc6dfdfa8.jpg
Before I mount the bed I have to move the angle strips up two inches and bed should fit like factory but the floor will be two inches higher.
