Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: stromberg 97`s on a 460 ??
          
   
   

Reply To Thread
Page 1 of 2 1 2 LastLast
Results 1 to 15 of 17

Hybrid View

  1. #1
    speedemon's Avatar
    speedemon is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Penrith
    Car Year, Make, Model: 32 Roadster
    Posts
    24

    stromberg 97`s on a 460 ??

     



    Hi does anyone know if anybody produces a inlet manifold to fit either 6 of preferably 8 stromberg 97`s onto a 460, or is there any other wild carb setups available ??

    Speedemon
    Speedy speedemon

  2. #2
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    No. The selection of intakes for a 460 are pretty much limited to one 4 barrel, two 4 barrels (Blue Thunder) and tunnel rams with either one or two 4 barrels.

    Only thing I think you could do is buy a blower manifold, made for like a 671 blower, and fab up a flat aluminum plate to fit it, and punch the appropriate holes in it for whatever carb layout you wanted.

    It wouldn't be super efficient, but I know what you are going for here. You want the old timey look of multi carbs, so efficiency is not the main goal, looks are.

    One 4 or two 4's will perform better in case that was a consideration.


    Don

  3. #3
    Big Tracks's Avatar
    Big Tracks is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2005
    Location
    Keller
    Car Year, Make, Model: '79 Dodge Diplomat Coupe
    Posts
    832

    You might take a look at http://victorylibrary.com/mopar/log-c.htm.

    Maybe it will give you some ideas. It deals with making a log intake for Chrysler engines but the principles should apply.

    Jim

  4. #4
    Big Tracks's Avatar
    Big Tracks is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2005
    Location
    Keller
    Car Year, Make, Model: '79 Dodge Diplomat Coupe
    Posts
    832

    Another thought, Demon, if you choose to go with 6 or 8 Strombergs you might TRY (emphasis on "try") to find 81's instead of 97's (smaller venturi).

    They might make it just a little more streetable if that's what you want.

    Jim

  5. #5
    speedemon's Avatar
    speedemon is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Penrith
    Car Year, Make, Model: 32 Roadster
    Posts
    24

    thanks for the replies, yes it is more looks than performance, I think the biggest problem will be with linkage to get them working progresivly
    Other big problem is that i will have to import them myself as no one in the UK stock them , so it will be a bit of trial and error
    My idea was why have just six when you have eight cylinders lol
    Any other idea`s keep them coming all info will help one way or another

    Craig
    Speedy speedemon

  6. #6
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    Since flatheads are popular, Strombergs are going to be pretty pricey right now, especially buying 8 of them. And I've never seen one that didn't leak. You have to limit fuel pressure to 3 psi. Nah, not for me.

    There is something I would pursue if I wanted to do what you're trying to do. I'd make my own manifold from mild steel. Start with 2 pieces to bolt to the heads, maybe 3/8" thick and machine the ports openings and bolt holes into them. Then I'd locate 8 motorcycle carbs from a motorcycle boneyard. I'd determine the angle they were mounted at on the mc and mount them on the 460 using straight tubing and bends fabbed together however you have to in order to make the angle correct, like a ram induction manifold on the Chrysler 413's from the 60's. I'd make a shallow fuel tank to mount on the cowl where the rear of the hood meets the firewall. I'd make it maybe 5-6" deep, 3-4" front to rear and the width of the engine bay. Motorcycles didn't use a fuel fump, so this cowl-mounted tank will fill the bowls by gravity. Mount a float in the tank to signal an electric fuel pump when the float drops to a certain level and shut off again when the float reaches the top of the cowl tank. That's how you would fill the cowl tank from the rear-mounted main tank.

    Wadda ya think?
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  7. #7
    71LincolnCoupe's Avatar
    71LincolnCoupe is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Sheridan
    Car Year, Make, Model: 1971 Lincoln Continental Coupe
    Posts
    72

    I think I need a drink... because I have a 460 and I want to play with it too!
    Please look below for more about my car...

    http://www.cardomain.com/member_pages/view_page.pl?page_id=278481

  8. #8
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    I've also been picking up Rochester 2gc carbs on Ebay for $15 t0 $ 20 each to use on a couple of tripower manifolds I have. The early ones (late 50.s to late 1960's) used the small bolt pattern and are perfect for most of the 4 bolt manifolds you can find. These were used on many small chevrolet small block 283/ 307 etc engines, and are a pretty good clone of the tripower carbs used on GTO's etc. If you want to get fancy, speedway sells the kits to make the bases have no idle circuits, for the outside carbs. Rebuild kits are about $ 20.00 at NAPA, etc.

    These are vastly improved over the old 97 fuel leakers, and other early ford carbs.


    Don

  9. #9
    shawnlee28's Avatar
    shawnlee28 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2004
    Location
    so.cal
    Car Year, Make, Model: 66 c 10 fleetside longbed
    Posts
    1,942

    I like the motor cycle carb idea!!!
    Its gunna take longer than u thought and its gunna cost more too(plan ahead!)

  10. #10
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    "I think I need a drink... "
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  11. #11
    thesals's Avatar
    thesals is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    san diego
    Car Year, Make, Model: 66 mustangFB, 69 econline Drag Van
    Posts
    1,527

    why not fuel inject it.... they had fuel injected 460s in some later model trucks.... and it would be kinda neat, and very driveable
    just because your car is faster, doesn't mean i cant outdrive you... give me a curvy mountain road and i'll beat you any day

  12. #12
    speedemon's Avatar
    speedemon is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2005
    Location
    Penrith
    Car Year, Make, Model: 32 Roadster
    Posts
    24

    Yeh could do that ,but looking for the old style look , wont get that with injection ,
    As for the motor bike carbs , not sure about that will look into it
    rochester carbs , will be as rare as rocking horse sh!T i think in the Uk

    Please keep the idea coming


    Craig
    Speedy speedemon

  13. #13
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    Yeah, I know the current trend is the nostalgia/rat rod look with tons of carbs on the engine, but to be honest they weren't all that hot back "in the day." In the early years of hot rodding we were trying everything to get more power, and we had very few places to buy ready made items, like we do today. So some really strange things started appearing on cars. Homemade intake manifolds of every description began to show up, including the log manifolds mentioned above. Because modern 4 barrel carbs hadn't shown up yet, we resorted to what we had and usually these were the old strombergs.

    However, the strombergs were known to leak fuel very often, and I understand recent developments by people who still build flathead parts have pretty much cured that ailment. Also, as mentioned, 97's are starting to get very very pricey. If you think the rochesters would be a problem, unless you have some UK source for strombergs that I don't know about, you are really going to lay out some shillings for the strombergs.

    The motorcycle carbs are probably a good idea from the standpoint of worldwide availability. Maybe there are some English cars that use something similar to the way strombergs mount and will give you that look.

    Good luck,


    Don

  14. #14
    thesals's Avatar
    thesals is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    san diego
    Car Year, Make, Model: 66 mustangFB, 69 econline Drag Van
    Posts
    1,527

    Quote Originally Posted by Itoldyouso
    Yeah, I know the current trend is the nostalgia/rat rod look with tons of carbs on the engine, but to be honest they weren't all that hot back "in the day." In the early years of hot rodding we were trying everything to get more power, and we had very few places to buy ready made items, like we do today. So some really strange things started appearing on cars. Homemade intake manifolds of every description began to show up, including the log manifolds mentioned above. Because modern 4 barrel carbs hadn't shown up yet, we resorted to what we had and usually these were the old strombergs.

    However, the strombergs were known to leak fuel very often, and I understand recent developments by people who still build flathead parts have pretty much cured that ailment. Also, as mentioned, 97's are starting to get very very pricey. If you think the rochesters would be a problem, unless you have some UK source for strombergs that I don't know about, you are really going to lay out some shillings for the strombergs.

    The motorcycle carbs are probably a good idea from the standpoint of worldwide availability. Maybe there are some English cars that use something similar to the way strombergs mount and will give you that look.

    Good luck,


    Don
    maybe give it a cross ram look using some carbs off of a yamaha xs1100 special.... i have 3 of those bikes 4 cyl 4 carbs, you'd only need to find to bikes in the junkyard and you'd be set..... the yamaha carbs are very well built carbs and easy to synchronize... they also each have their own K&N filter on them so they'd look pretty nifty on a homemade manifold
    just because your car is faster, doesn't mean i cant outdrive you... give me a curvy mountain road and i'll beat you any day

  15. #15
    R Pope is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    Eston
    Posts
    2,270

    A cross-ram log manifold with eight SU's would do it for me!

Reply To Thread
Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink