Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: cost to rebuild 53 Plymouth Flat 6
          
   
   

Reply To Thread
Results 1 to 9 of 9
  1. #1
    prosperpc is offline Registered User Visit my Photo Gallery
    Join Date
    Aug 2009
    Location
    Lexington
    Posts
    1

    Question cost to rebuild 53 Plymouth Flat 6

     



    When I was born, my great grandmother willed me a 1953 Plymouth Cranbrook sedan. For pretty much 25+ years it has been stored in a garage where the flat 6 engine has frozen up. I recently decided to put this thing in running condition again but am having a LOT of trouble with the frozen engine. Dropped it off to a mechanic but after several weeks of soaking in oil and removing top half, its still stuck. Any ideas? Also, what is a reasonable cost range to pull the engine and rebuild it?

    Any help is much appreciated!

  2. #2
    robot's Avatar
    robot is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Tucson
    Car Year, Make, Model: 39 Ford Coupe, 32 Ford Roadster
    Posts
    2,334

    Throw out some more info regarding your intent.....are you set on keeping the original engine block? You probably can find a serviceable block that is not frozen that would be cheaper than machining out the pistons and/or sleeving the original block. Are you intent on keeping the engine all original or are you wanting to modernize it a bit? Fortunately, the old flathead six was used in quite a few applications (even forklifts) and parts are relatively cheap and available.

    You might search for a MoPar owners site that specifically focuses on the older models...they would have a good contact list of who specializes in rebuilds and parts.

  3. #3
    falconvan's Avatar
    falconvan is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2007
    Location
    festus
    Car Year, Make, Model: 48 Plymouth, 48,54 Heap
    Posts
    3,407

    Check out the the P15 D24 site; it's strickly old Mopars owners and has lots of stuff for sale. Those guys can help you out.

  4. #4
    JeffB2's Avatar
    JeffB2 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2007
    Location
    Phoenix
    Car Year, Make, Model: 1954 Ford Customline 5.0 & AOD
    Posts
    443

    Mopar 6 help

     



    Also check out the OlSkoolRodz website several of the guys have done builds on these engines and have posted some good pics too.

  5. #5
    tinlizzy is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2010
    Location
    Mount Carmel
    Posts
    3

    flat head

     



    It can be rebuilt it just depends on what you plan to do. Should cost about 2500 to get a rebuild. You might try logging on the P15-D24 forum for great info on these old girls. Lots of help and good place to get info on the cars. You will have to register but same as it is here.
    Good Luck
    Lee

  6. #6
    Cratered Flats is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2010
    Location
    Magic Valley
    Car Year, Make, Model: 27 T Roadster
    Posts
    4

    One thought is that there are lots of flat sixes that will swap out. However the Chryslers and Desoto sixes are longer and will not always fit. However, Dodges and Plymouths are the same externally. I picked up a nice 48 Chrysler six because the owner could not fit it into the engine bay of his Plymouth car. Check this site...........................http://www.allpar.com/mopar/flat.html

  7. #7
    Cratered Flats is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2010
    Location
    Magic Valley
    Car Year, Make, Model: 27 T Roadster
    Posts
    4

    Engine bay

     



    I thought I would mention to be careful about replacing your Plymouth engine with anything other than a Dodge or another plymouth. I picked up a good deal on a 48 Chrysler flat six and it is too long to fit into the Plymouth engine bay. Looks the same at first glance, but is about three inches longer.

  8. #8
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    There are as many degrees of "rebuilding" an engine as there are people doing it. Some consider new rings, bearings, and gaskets a rebuild. Others go to the extent of checking the block and all components for cracks, then machining everything and using as many new parts as possible. All depends on the amount you want to spend and your expectations.

    Sounds like you are considering having someone do the pulling, rebuilding, and reinstallation for you. BE VERY CAREFUL. There are thousands of horror stories of people who paid big money to get that kind of work done and ended up with a crap job, or one left half done. Not every garage or mechanic is able to do these older engines. They seem very simple on the surface, compared to the computer laden ones out there today, but it takes a mechanic and machinist who understand flatheads to get them right.

    These flathead 6's were practically bulletproof. A buddy when I was a teen had a 50 Plymouth that he kept trying to blow up so his Dad would give him his 62 Chevy instead. No matter how hard he ran it the thing wouldn't die. But your first concern is getting that engine freed up. You might try soaking it in molasses in a big tub. Never done that myself, but I have heard it works miracles and molasses can be bought in huge bags at feed stores, I think. Sometimes I have freed them up using a torch to heat each piston top and pouring penetrating oil down the cylinders. Tapping with a wood block and bfh really helps too.

    Don
    Last edited by Itoldyouso; 12-18-2010 at 10:12 AM.

  9. #9
    Malicious is offline Registered User Visit my Photo Gallery
    Join Date
    Jul 2011
    Location
    Melbourne
    Posts
    1

    Believe it or not but Coke works a treat. Thats the branded cola, but the dust. I imagine any brand will do, but a mate of mine sat coke in the bores of a seized engine and got it free spinning.

    Makes you wonder what its doing to your innards :P

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink