Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Increase the compression ratio
          
   
   

Reply To Thread
Results 1 to 4 of 4
  1. #1
    James911 is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2007
    Location
    B
    Posts
    7

    Increase the compression ratio

     



    Hi,
    just a couple of question about increasing the compression ratio (CR).

    There are some facts thats influences the CR:

    1. Head design -->chamber volume
    2. Pistons design
    3. bore diameter
    4. the type of head gasket (thickness)

    If I port my head, I will increase the chamber volume and therefore decrease the CR. How much is that usually? Which effect is bigger?

    An other possibility to increase the CR is to machine my cylinder heads. But I heard this might cause trouble with the intake mainfold. It might not fit tight? Is this correct?

    Is it not better to machine the block? In my Chevy 350 cui is enough space at the top before the valves will hit the pistons. I have never read something about machine the block to get a smaller chamber and better CR.
    What do you thing about that idea?

    Regards

    James

  2. #2
    mooneye777's Avatar
    mooneye777 is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    dayton
    Car Year, Make, Model: 1948 ford anglia
    Posts
    978

    if you are running stock dish pistons it would be a huge waste of money to machine the block and or heads to increase compression. you could slap a set of ..018 copper head gaskets for a quick up in cr/. but it probably would not be cost effective to do it for the small gain for all the bloody knuckle work needed to do it. bottom line is a new set of flat top pistons as being the best way to raise a street motor cr/. but then you will need to increase fuel and air intake and exhaust cappacities to do it right. so if you are asking for a cheap easy way to raise your compression to boost performance the answer is probably not! i hope this answers your question, if not let us know.


    Live everyday like it were your last, someday it will be.

  3. #3
    threearmsinjune is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2006
    Location
    Indianapolis
    Car Year, Make, Model: 79 shovel, 65 pan
    Posts
    133

    Quote Originally Posted by James911
    Hi,
    just a couple of question about increasing the compression ratio (CR).

    There are some facts thats influences the CR:

    1. Head design -->chamber volume
    2. Pistons design
    3. bore diameter
    4. the type of head gasket (thickness)

    If I port my head, I will increase the chamber volume and therefore decrease the CR. How much is that usually? Which effect is bigger?

    An other possibility to increase the CR is to machine my cylinder heads. But I heard this might cause trouble with the intake mainfold. It might not fit tight? Is this correct?

    Is it not better to machine the block? In my Chevy 350 cui is enough space at the top before the valves will hit the pistons. I have never read something about machine the block to get a smaller chamber and better CR.
    What do you thing about that idea?

    Regards

    James
    James there are a few things to consider. First a port job usually has to do with the material around the valve in the port (outside of the chamber) there is usually very little taken out inside the combustion chamber except to unshroud the valves. If you are having machine work done to your heads do this first and then measure the volume of the combustion chamber. This gives you a concrete number to start working with. If you are going to any work to the block do this next but take some measurements first. When the piston is at TDC what is the distance from the block surface to the top of the piston where it meets the cylinder wall? Use this measurement to set up your quench area(along with the compressed thickness of the gasket). If you have the budget and some time next to consider is cam and pistons. Pistons are advertised to have a certain size/volume dome or dish. Before buying a complete set, try one and have the top face of it measured. I recently purchased a set of +5cc domes as advertised that actually measured to be -.3cc when accounting for the valve reliefs. Camshaft timing, especially intake closing is influential to DCR.
    In short there are a lot of things to consider along with compression but time and budget are very limiting factors. Anything worth doing is worth being informed about. Form a plan and stick to the plan. From experience I can say that direct measurements are far better than "advertised". The guys and gals here have lots of collective knowledge and are always glad to help.
    Chris

  4. #4
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Got to wonder why you're going for raising the compression ratio??? Lots of ways to improve performance more efficiently then raising the compression...... Just curious, that's all....
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink