Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: tpi setup w/ vortec heads
          
   
   

Reply To Thread
Results 1 to 7 of 7
  1. #1
    clyde is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2003
    Location
    maryland
    Car Year, Make, Model: 1991 camaro rs
    Posts
    3

    Unhappy tpi setup w/ vortec heads

     



    project tpi... at the track she ran 14.02 lost power around 3000 feet. what can i do for top end speed. i was told that tpi was only good for torqe.

  2. #2
    krys_671 is offline Registered User Visit my Photo Gallery
    Join Date
    Sep 2003
    Location
    Indiana
    Car Year, Make, Model: 84 Firebird
    Posts
    1

    I once read that shorter runners would boost top end...but have never seen anything shorter then stock...

  3. #3
    clyde is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2003
    Location
    maryland
    Car Year, Make, Model: 1991 camaro rs
    Posts
    3

    i'm thinking of putting in a larger cam right now i have a 500 510 lift with votec heads,1.6 rockers stock intake, runners, 24lbs. injectors and stock throttle body. any sugestions on what i can change.. that will make a differance.

  4. #4
    screamer63_1979's Avatar
    screamer63_1979 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Beaver
    Car Year, Make, Model: 90 Jeep Wrangler
    Posts
    368

    you have lots of lift, and with the 1.6 rockers...wow.

    as long as the valve train is not binding (check springs, read that to exceed .5 lift on vortec you needed different springs...) you are OK.

    Headers or cat(s)? After cat system or is everything sotck?

    An engine is an air pump - the more air you can pump through it the better.

    You could try a pass with the vac line off the fule pressure regulator - it will allow slightly more fuel. If the cam has changed and the injectors/chip have not, youare probably starving for fuel on the top end.

    Don't know limits of TPI system, but yes, long small diam runners (on any intake for that matter) are engineered for low rpm usage. High RPM want short runs that are large in diameter. Some intaked have been tried that have siamesed runners - 2 small diam that toghether make one large one to try and get best of both worlds.

    What are you running for air cleaner/snorkel, etc? ON camaros vs firebird from best to worst design can mean 20+ HP! Now you gonna ask which is best, aren't ya? I can look that up, but Car CRaft did an article on TPI not too long ago.
    Chris
    Only the dead fish go with the flow.

  5. #5
    clyde is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2003
    Location
    maryland
    Car Year, Make, Model: 1991 camaro rs
    Posts
    3

    yes life is hard, when it get tough we go home. hey chip has been done. i'll take it to get dino and find out what's up.. no air restriction. msd dist, msd box, hi ignitn coil, fuel press set at 45. i've heard that tpi systems like low rpms. so how can i get belowwwww 14.02 i've hit my head against the wall several times ...i"m okay now... duration 210 220

  6. #6
    kidrcth is offline Registered User Visit my Photo Gallery
    Join Date
    Jan 2004
    Location
    jacksonville
    Posts
    1

    d00d, your seup is made for torque. To improve your times, what you need todo is put better gears in the rear end.

    Alright if you have an auto tranny you got a 3.23, which means you need a 3.73.

    If you have a manual you have a 3.42, then put a 3.92 in and it'll improve your times.

    You can get these, they aren't hard to install, for less that $200, usually around $150. try http://www.summitracing.com . After this your high amount of torque will tranform your RWHP to something way higher when dyno'd.



    Currently i am building the same setup. I have the vortec kit from SDPC, and the 350 just sitting around waiting to be built after i get all the parts. i need the 350 injectors,the aftermarket runners, headers, and to port my plenum. The i'll be shitting out horsepower like nothing before.

  7. #7
    skullmaster427s is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2004
    Location
    newark
    Car Year, Make, Model: 84 chevy el caminos SS 72chevelle SS
    Posts
    4

    what's up people... by the way i'm new here still dont know yet how averything works but i already have few questions... first the tpi plate will not fit vortec heads? if not is it possible to make it fit? does anyone makes baseplate for the tpi to fit vortec heads? if not what kind mods do i need to do to the lowerintake or base plate .... any ideas or solutions pls email me at sickchevy350@yahoo.com

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink