Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Need help with old Buick Nailhead Tuning
          
   
   

Reply To Thread
Results 1 to 3 of 3
  1. 03-31-2005 07:20 AM #1
    pwoudenberg
    pwoudenberg is offline Registered User
    Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Scottsdale
    Car Year, Make, Model: 37 Buick Special
    Posts
    2

    Need help with old Buick Nailhead Tuning

     



    I have a 53 322 buick nailhead engine in my 37 Buick special. It has been completely redone, new pistons, valves, everything. Also sanderson headers (fit great!), also pertronix ignition and flamethrower coil. Have 4bbl Edelbrock the basic one, model 1405, about 500cfm I think. Problem is I can't seem to get this whole setup running right. It starts just fine, and will idle fairly well, when I rev it up it sounds just fine. But when I try to drive it, it stumbles on acceleration, and when I get it revved up then it pops a little bit when I let up. I'm not sure what to check next, and can't seem to find many guys with knowledge in old carbed engines... any ideas of how you would start the tuning process would be great!
    Thanks
    .
    Reply With Quote Reply With Quote
  3. 04-05-2005 08:35 PM #2
    pwoudenberg
    pwoudenberg is offline Registered User
    Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Scottsdale
    Car Year, Make, Model: 37 Buick Special
    Posts
    2

    Nailhead Tuning

     



    Denny, thanks for the information! it was helpful but here was my 1st problem. Incorrect timing due to no markers for TDC. I measured the circumference of my harmonic balancer and using that I made my own Timing Tape with degrees marked in 5's. Found out that I was running at 45 degrees advanced, WOW, no wonder I was having such a hard time!
    After dialing it back to 5-10 degrees I was then able to tune the carb a lot better and then was able to use all of the information you sent.
    Still having some issues there but I'll keep trying.
    now on to the problem of getting the TV cable properly setup to work with my TH200 4R trans!
    If its not one thing its another!
    Reply With Quote Reply With Quote
  4. 04-06-2005 06:55 PM #3
    '60buickrod's Avatar
    '60buickrod
    '60buickrod is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Mar 2004
    Location
    Mount Pleasant
    Car Year, Make, Model: 1960 Buick LeSabre
    Posts
    84

    is your accelerator pump working?
    Also do you know about V8buick.com or better yet The Nailhead group?
    Gerig Michael H.
    -----------------------------------
    '60 Buick LeSabre Flat top x2
    '78 Mercury Monarch 2-door ghia(1 of 2 know)
    '66 Pontiac Catalina(brother)
    '98 Cadillac DeVille(parents)
    Wanted: '60 LeSabre A/C components
    -----------------------------------
    "There is no doubt about precisely when folks began racing each other in automobiles.
    It was the day they built the second automobile." -Richard Petty
    Reply With Quote Reply With Quote
Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules

Links monetized by VigLink