Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Pilot Bearing install?
          
   
   

Reply To Thread
Results 1 to 11 of 11
  1. #1
    Rugratman's Avatar
    Rugratman is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Annapolis
    Car Year, Make, Model: 67 Pontiac GTO
    Posts
    58

    Pilot Bearing install?

     



    What does it mean to " Stake " the pilot bearing into the end of the Crank?

    I am swapping from a TH400 to a 4 speed.
    I am sure I will have a few more questions...
    I am just learning as I go.

  2. #2
    HOSS429's Avatar
    HOSS429 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2007
    Location
    New Market
    Posts
    2,584

    put little pin pricks ( chisel punches ) around the perimiter of the bearing to expand it for more solid fit .. although iv`e never done and never had a related faliure
    iv`e used up all my sick days at work .. can i call in dead ?

  3. #3
    Rugratman's Avatar
    Rugratman is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Annapolis
    Car Year, Make, Model: 67 Pontiac GTO
    Posts
    58

    The outside race does not move, correct?
    Can I just locktite it in there?
    I am just learning as I go.

  4. #4
    HOSS429's Avatar
    HOSS429 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2007
    Location
    New Market
    Posts
    2,584

    if you are using a metal ( steel ) bearing type i`m not real sure what you should do .. i thought perhaps you were using the old style brass .. either way iv`e still never staked one in .. unless it slips in by hand pressure then you may have a too loose fit situation ..
    iv`e used up all my sick days at work .. can i call in dead ?

  5. #5
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    Highly recommend a solid brass or oilite bushing instead of a bearing. A bushing, unlike a bearing, will still operate when it's worn out.
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  6. #6
    Rugratman's Avatar
    Rugratman is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Annapolis
    Car Year, Make, Model: 67 Pontiac GTO
    Posts
    58

    Does Napa carry them? Or do I order it from Summit...?

    Installed the same way?
    I am just learning as I go.

  7. #7
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    I do not know where the term “stake a bearing” originated, but it refers to a small punch (or series of punches) used to hold the bearing in place during assembly. I have never needed to stake a pilot bearing. Typically, once they’re installed in the end of the crankshaft they’re pretty snug. In fact, most times a pilot bearing puller is required to remove them.

    My bet is that you will have to tap the bearing in place - very carefully with a brass hammer or use a wooden dowel to avoid damage. The outer edge of the bearing should be snug against the crankshaft and not spin.

    If necessary, the stake should take place as per the picture below, i.e, at the lip where the two surfaces meet to hold the bearing in place.

    Regards,
    Glenn
    Attached Images

  8. #8
    HOSS429's Avatar
    HOSS429 is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2007
    Location
    New Market
    Posts
    2,584

    oilite bushing is correct .. everyone should have them
    iv`e used up all my sick days at work .. can i call in dead ?

  9. #9
    glennsexton's Avatar
    glennsexton is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Mar 2005
    Location
    Tigard
    Car Year, Make, Model: 63 Nova SS
    Posts
    2,572

    Man you guys are too quick for me - I would concur with all of the above. The race should not move against the crankshaft, use a brass or oilite bushing if possible.

    You will be able to find what you need at NAPA.

  10. #10
    Rugratman's Avatar
    Rugratman is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Annapolis
    Car Year, Make, Model: 67 Pontiac GTO
    Posts
    58

    Sweet, thanks guy's.....
    I am just learning as I go.

  11. #11
    cffisher's Avatar
    cffisher is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    Constantine
    Car Year, Make, Model: 57 chevy 2 dr wagon
    Posts
    9,476

    Changed a clutch in a Mustang not long ago had a bearing not bushing, had to burn it out. Not a priety site.
    Charlie
    Lovin' what I do and doing what I love
    Some guys can fix broken NO ONE can fix STUPID
    W8AMR
    http://fishertrains94.webs.com/
    Christian in training

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink