Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Ballast resistor or not?
          
   
   

Reply To Thread
Results 1 to 5 of 5
  1. #1
    falconvan's Avatar
    falconvan is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2007
    Location
    festus
    Car Year, Make, Model: 48 Plymouth, 48,54 Heap
    Posts
    3,407

    Ballast resistor or not?

     



    When I was changing my Mopar flattie over to 12 volt, I got an article off the internet and it said if you are using a modern 12 volt aftermarket coil, you do not need a ballast resistor because it is built into the coil. Well, I smoked the coil last night so i'm wondering if I do need one or how I can determine if I need one. It was a new coil and only ran a handful of times. Anyone have any experience with this?

  2. #2
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,334

    The ballast resistor is used to keep from burning up the points and is only in the system when the ignition switch is in the run position. If it was eliminated I would think you'd burn up the points before you smoked the coil.
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  3. #3
    Sniper is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jan 2007
    Location
    Watford
    Car Year, Make, Model: Various Projects
    Posts
    142

    The resistor is there to knock the voltage down to 8 volts so the coil won't be damaged. If your new coil has an internal resistor, it should be printed or stamped on the outside case. If there's nothing there, it's possible you have a regular coil that wouldn't handle the 12 volt and went poof. Mislabled box, switched somewhere along the way, when comparing an internal to an external resistor coil? Don't know just a guess. If your using an early style ignition, with a resistor, you should have a single wire from the distributor to the coil,(neg. side) and two wires to the opposite terminal of the coil.(pos. side) Of the two wires, one will come from the resistor that will supply 8 volt, or close to it. And the other wire will come from the starter solenode to supply 12 while cranking the engine over to start it. There's a terminal on the solenode that is energized only while your cranking the engine over, I'm not refering to the trip wire from the key switch that is used to start the engine, that's a seperate terminal on the solenode. So, now that, that is as clear as mud, you likely didn't need that part anyway. Some systems that used the internal resistor coil, just had one wire to the pos. side of the coil, and no jumper from the starter. Didn't need it, it had 12 volt all the time and knocked it down to 8 volt internally. No "boost" in voltage could be gained like you would get with the external system. So now it remains to figure out, is the coil the wrong one, or just a faulty one. Warranty can be a bit tough to get on electrical componets sometimes, best of luck though. Sniper

  4. #4
    kitz's Avatar
    kitz is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    Austin
    Car Year, Make, Model: 32 Roadster, BBC
    Posts
    962

    The ballast or condenser acts similarly to a snubber by 'snubbing' out voltage transients during the act of opening the points. These transients occurr due to the points being connected to an inductor (the primary coil circuit). Electrical inductors don't like the current to change so they can jack the voltage way up to compensate. Without the ballast it is possible for this inductor to develop voltages that are too high for the coil primary insulation causing short life or even instant failure.

    Kitz
    Jon Kitzmiller, MSME, PhD EE, 32 Ford Hiboy Roadster, Cornhusker frame, Heidts IFS/IRS, 3.50 Posi, Lone Star body, Lone Star/Kitz internal frame, ZZ502/550, TH400

  5. #5
    falconvan's Avatar
    falconvan is offline CHR Member Visit my Photo Gallery
    Join Date
    Mar 2007
    Location
    festus
    Car Year, Make, Model: 48 Plymouth, 48,54 Heap
    Posts
    3,407

    This helps a lot. Thanks, everyone.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink