Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: URGENT! before I drill my firewall need advice :)
          
   
   

Reply To Thread
Results 1 to 11 of 11
  1. #1
    HiboyGal's Avatar
    HiboyGal is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2006
    Location
    Los Angeles
    Car Year, Make, Model: 32 Ford Hi Boy Roadster
    Posts
    305

    URGENT! before I drill my firewall need advice :)

     



    Long time no post, but tonight I can't catch up, so I'll have to post later about the last 3 week long ordeal with my car paint job (don't laugh)...

    FOR NOW URGENTLY NEED TO KNOW:

    Is it OK to bolt my ignition coil, with it's brand new slip on finned cover to my FIBERGLASS FIREWALL... the coil and cover get a bit heavy and I know fiberglass is not all that strong. I plan to affix a strong metal plate about 2 inch high and 6 inch long to the INSIDE of the firewall to help spread the pressure of the two bolts to a larger surface area.

    Still, I worry that with the slight weight and the roadster bouncing up and down the road, the firewall may crack if I bolt this coil to it.

    Then again, it is probably OK but before I drill my firewall tomorrow I wanted to ask someone else here who might have done this on a glass car...?

    thanks for your input.
    FAITH
    ________________
    www.myhiboy.com

  2. #2
    John Palmer is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2004
    Location
    Santa Ana
    Car Year, Make, Model: '32 High Boy, '60 VW, Teardrop Trailers
    Posts
    355

    Quote Originally Posted by HiboyGal
    Long time no post, but tonight I can't catch up, so I'll have to post later about the last 3 week long ordeal with my car paint job (don't laugh)...

    FOR NOW URGENTLY NEED TO KNOW:

    Is it OK to bolt my ignition coil, with it's brand new slip on finned cover to my FIBERGLASS FIREWALL... the coil and cover get a bit heavy and I know fiberglass is not all that strong. I plan to affix a strong metal plate about 2 inch high and 6 inch long to the INSIDE of the firewall to help spread the pressure of the two bolts to a larger surface area.

    Still, I worry that with the slight weight and the roadster bouncing up and down the road, the firewall may crack if I bolt this coil to it.

    Then again, it is probably OK but before I drill my firewall tomorrow I wanted to ask someone else here who might have done this on a glass car...?

    thanks for your input.

    Do it!

    I see no problem with the installation as you have outlined. It would take a tank to pull it off the firewall with a 2x6 backing plate.

  3. #3
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    Everybody has been wondering where you got to.

    You will be fine, Faith. The backer is a good idea, and I would drill the hole, then use a countersink bit to lightly dress the holes on both sides, to keep the holes from wanting to stress crack. Don't countersink deeply, just bevel it ever so slightly. We did this in the marine industry to keep hardware from stress cracking the glass.

    If you were asking about a master cylinder, that is another matter, but a coil and the cover should be no problem at all.


    BTW, people have been wanting to see your new bias tires. Are they on yet?


    Don

  4. #4
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    Having the same concerns you have would keep me from doing it. I'd fab up some brackets to bolt it to the motor. I don't like clutter on the firewall either.
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  5. #5
    joeybsyc's Avatar
    joeybsyc is offline CHR Member Visit my Photo Gallery
    Join Date
    Oct 2006
    Location
    Johnstown
    Posts
    364

    The windshield is bolted to the fiberglass too, and it weighs more than a coil i think. You'll be surprised how thick that fiberglass is when you drill through it, no worries bolting a coil to the firewall.
    Joe Barr
    1932 Ford Roadster

  6. #6
    HiboyGal's Avatar
    HiboyGal is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2006
    Location
    Los Angeles
    Car Year, Make, Model: 32 Ford Hi Boy Roadster
    Posts
    305

    Quote Originally Posted by Itoldyouso
    Everybody has been wondering where you got to.

    You will be fine, Faith. The backer is a good idea, and I would drill the hole, then use a countersink bit to lightly dress the holes on both sides, to keep the holes from wanting to stress crack. Don't countersink deeply, just bevel it ever so slightly. We did this in the marine industry to keep hardware from stress cracking the glass.

    If you were asking about a master cylinder, that is another matter, but a coil and the cover should be no problem at all.


    BTW, people have been wanting to see your new bias tires. Are they on yet?


    Don
    Ok so this is the part where I come across as an idiot but what's countersinking?
    FAITH
    ________________
    www.myhiboy.com

  7. #7
    R Pope is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    Eston
    Posts
    2,270

    Countersinking is just tapering the hole so a flush-headed, tapered bolt will work. Like a valve seat, kinda
    Don't forget to run a ground wire to the coil, or to the inside plate.

  8. #8
    C9x's Avatar
    C9x
    C9x is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2004
    Location
    N/W Arizona
    Car Year, Make, Model: Deuce Highboy roadster
    Posts
    1,174

    Here's a couple of examples in some tools I made.

    The first, a very deep countersink in 1" OD (Outside Diameter) aluminum into a 3/8" ID (Inside Diameter) hole.

    The second, a medium deep countersink in the holes between two small holes in a wheel drill jig I made.

    The last in the small (1/4-20) threaded holes between lugnuts in an aluminum wheel.


    To accomplish these you'll need a "Countersink" (that's the right name).
    They come in ether 87.5 degree angle or 90 degree angle.
    The 87.5 degree angle is the best choice and usually what's available.

    For obvious reasons, you'll need one with an OD larger than the hole.

    To use one, mount it in your drill motor, hold the countersink in the hole and hit the trigger.
    With fiberglass you don't want the countersink spinning before you contact it.

    You'll just need to hit the drill motor trigger for a half second or less.
    To much and you'll have too large a countersink.

    One piece of advice when drilling fiberglass - new or painted, cured paint for sure - cover the hole area with a single layer of masking tape.
    Mark the masking tape where you're going to drill.
    A moderately sharp pencil point works well.
    Put the pilot drill (1/8" diameter or so) onto the mark with the drill motor not running, hit the trigger and drill.
    Next drill for the correct size and the pilot hole will guide your drill.
    Use caution when getting close to the other side so as not to break the edges of the hole and make a ragged hole.

    All that said, I wouldn't bother about countersinking fiberglass.
    Drill it and use standard flat washers to spread the load.
    The thinner stainless flat washers work well.

    Even better are "Fender Washers".
    Called such due to their large OD as compared to the hole ID.
    These spread the load well and can be improved by laying the Fender Washer on a piece of wood and hitting the hole with the round end of a small-medium ball peen hammer.
    This imparts a very moderate, almost flat cone shape to the washer and gets the loaded area out away from the hole in the fiberglass.

    Never had any problems doing fiberglass this way and that's talking about over 200 holes in a fiberglass sailboat as well as several holes in my Wescott body 32.

    The backup plate you plan to use sounds like the best way to go to hang a coil on a narrow bracket.
    Attached Images
    C9

  9. #9
    Henry Rifle's Avatar
    Henry Rifle is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2004
    Location
    Little Elm
    Car Year, Make, Model: 34 Ford Low Boy w/ZZ430 Clone
    Posts
    3,890

    Faith,

    Short answer. . . with the backing plate, you won't have a problem.
    Jack

    Gone to Texas

  10. #10
    C9x's Avatar
    C9x
    C9x is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2004
    Location
    N/W Arizona
    Car Year, Make, Model: Deuce Highboy roadster
    Posts
    1,174

    One thing I meant to add was, don't try to countersink with a larger drill.
    A true Countersink is designed to run true.
    You'll find them with 3-4 cutting edges - most common - as well as with a single cutting edge.
    Get the single cutting edge version because it's the smoothest running one.

    Countersinking with a large drill will have the drill chattering and in some cases walk right off the hole you're attempting to countersink which creates damage as it goes.
    The chattering also leads to a ragged countersink in most cases.


    However, and this is just for the heck of it.
    You can countersink for common allen head bolts with a regular drill when you're making auminum brackets and the like.
    Shown in the pic below.

    The drill used to countersink is just a few thousandths larger than the head of the allen bolt.
    Most times I go deep enough so the allen head is almost flush with the surface of the aluminum.
    Other times, part way.
    Makes for a nice finished product.

    You may be wondering how it works out since the inner countersink has an angled surface, but what happens is, a few tighten/loosen cycles will create a flat ledge for the allen bolt and it will go no deeper.

    I like this look and would rather do it this way than use FH (FlatHead) allen bolts sunk flush with the surface.
    Attached Images
    C9

  11. #11
    poncho62's Avatar
    poncho62 is offline CHR Member Visit my Photo Gallery
    Join Date
    Feb 2004
    Location
    Hanover, Ontario, Canada
    Car Year, Make, Model: 51 Ford Pickup
    Posts
    416

    Don't forget, the coil or bracket has to be grounded.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink