the casting mark seams to be about 1/2 inch wide .. i think you do have a good steel crank ..
Printable View
the casting mark seams to be about 1/2 inch wide .. i think you do have a good steel crank ..
Another update for everyone. The date code on the block is K16. Date code on heads are D964 (drivers side) and J165 (passenger side). Intake manifold codes are 3877652 and K35.
I probably won't tear into it any more until later this week.
https://c1.staticflickr.com/4/3873/3...559e052a_z.jpg
https://c1.staticflickr.com/4/3683/3...9d5f0e62_z.jpg
https://c1.staticflickr.com/4/3808/3...67541b4e_z.jpg
https://c1.staticflickr.com/1/719/32...95841f30_z.jpg
Today I removed the water pump, crank pulley, harmonic balancer, oil pump, intake manifold, rocker arms, pushrods, cylinder heads, timing chain & sprocket, and main bearing caps. I'll remove the rod bearings, crank, and pistons/rods tomorrow. I forgot to take some pictures of the bearings in the main caps, but I'll get them tomorrow with all the rest of the bearings.
https://c1.staticflickr.com/3/2838/3...958a00fc_z.jpg
https://c1.staticflickr.com/4/3949/3...ed1097ba_z.jpg
https://c1.staticflickr.com/3/2916/3...dc3ec991_z.jpg
https://c1.staticflickr.com/4/3678/3...00727d99_z.jpg
https://c1.staticflickr.com/4/3853/3...45b0f4cd_z.jpg
https://c1.staticflickr.com/3/2806/3...2c642c92_z.jpg
https://c1.staticflickr.com/3/2887/3...a7d1f741_z.jpg
https://c1.staticflickr.com/4/3674/3...6430d948_z.jpg
https://c1.staticflickr.com/3/2855/3...5ec5bc12_z.jpg
https://c1.staticflickr.com/4/3762/3...d0302db2_z.jpg
https://c1.staticflickr.com/3/2837/3...a72f1287_z.jpg
https://c1.staticflickr.com/3/2840/3...923ffb3d_z.jpg
https://c1.staticflickr.com/1/592/33...df35eb78_z.jpg
I got everything removed from the block today (except camshaft bearings). Looks like the rod bearings for #5 cylinder failed which was causing the rod knock that the previous owner had mentioned.
The main journals measured 2.3 inches and the rod journals measured 2 inches. The pistons/cylinders measured 4 inches.
Upper main bearings were stamped:
57653 GMM420 293G5 (2x)
57653 GMM420 293J5 (2x)
GMMA 57868 287HH5
Lower main bearings were stamped:
57653 GMM420 258N5 (4x)
GMMA 57868 180A5 (the A was upside down)
Rod bearings were stamped:
57734 GMM500 280N5 (4x)
57734 GMM500 280J5 (3x)
57734 GMM500 280J3 (1x)
57734 GMM500 288A5 (1x)
57734 GMM500 280B5 (1x)
57734 GMM500 253E5 (1x)
57734 GMM500 287X5(1x)
57734 GMM500 280A5 (1x) (the A was upside down)
57734 GMM500 280L5 (1x)
unknown trashed bearings (2x)
Crankshaft was stamped:
4577 (I didn't notice another number anywhere)
Camshaft was stamped:
K1 GM84 2798
Pistons were stamped:
3796494
https://c1.staticflickr.com/3/2944/3...4cf88d32_z.jpg
https://c1.staticflickr.com/3/2817/3...89ca0917_z.jpg
https://c1.staticflickr.com/4/3804/3...50871810_z.jpg
https://c1.staticflickr.com/3/2898/3...b50238c7_z.jpg
https://c1.staticflickr.com/3/2864/3...391a2206_z.jpg
https://c1.staticflickr.com/4/3945/3...5302700d_z.jpg
https://c1.staticflickr.com/3/2854/3...0ab4d9d0_z.jpg
https://c1.staticflickr.com/4/3673/3...2374709e_z.jpg
https://c1.staticflickr.com/3/2849/3...88d367ff_z.jpg
https://c1.staticflickr.com/4/3829/3...39dd6d74_z.jpg
https://c1.staticflickr.com/3/2858/3...90a00b9b_z.jpg
bad rod bearings (#5)
https://c1.staticflickr.com/3/2876/3...20d4751e_z.jpg
crankshaft wear from bad bearings (#5)
https://c1.staticflickr.com/4/3810/3...7a8e83bb_z.jpg
rod wear from bad bearings (#5)
https://c1.staticflickr.com/3/2948/3...bd685350_z.jpg
#2 cylinder
https://c1.staticflickr.com/3/2823/3...bd2a27d1_z.jpg
#4 cylinder
https://c1.staticflickr.com/4/3741/3...da5dfe91_z.jpg
#6 cylinder
https://c1.staticflickr.com/4/3755/3...016b045e_z.jpg
#8 cylinder
https://c1.staticflickr.com/3/2819/3...f22ec97b_z.jpg
#1 cylinder
https://c1.staticflickr.com/3/2928/3...64437e66_z.jpg
#3 cylinder
https://c1.staticflickr.com/3/2879/3...edc8fda9_z.jpg
#5 cylinder
https://c1.staticflickr.com/3/2849/3...dbee129d_z.jpg
#7 cylinder
https://c1.staticflickr.com/3/2900/3...ed367fd2_z.jpg