Vortec No-Machine Valve Springs!

Printable View

12-12-2005, 01:13 PM
MainCap

Vortec No-Machine Valve Springs!

A little info back to the group,

I came across the following valve springs and retainers from Crane Cams that increase lift clearance on Vortec heads without the need to machine anything.

They are Crane Cams, PN: 10309-1 Springs and Retainers. About $160.00 for a set of 16.

According to the Sallee Chevrolet site these are good for up to .550 lift.

Probably not the end all solution for the more radical amoung us but for those that want more cam than the .450 lift limitation of the stock vortec head allows, these may be a cost effective solution.

Anyway - there ya go!
12-12-2005, 01:29 PM
erik erikson

Re: Vortec No-Machine Valve Springs!

Quote:

Originally posted by MainCap
A little info back to the group,

I came across the following valve springs and retainers from Crane Cams that increase lift clearance on Vortec heads without the need to machine anything.

They are Crane Cams, PN: 10309-1 Springs and Retainers. About $160.00 for a set of 16.

According to the Sallee Chevrolet site these are good for up to .550 lift.

Probably not the end all solution for the more radical amoung us but for those that want more cam than the .450 lift limitation of the stock vortec head allows, these may be a cost effective solution.

Anyway - there ya go!

$160 FOR SPRINGS AND RETAINERS?MY LAST SET OF SPRINGS,AND RETAINERS DID NOT COST THIS MUCH FOR MY ROLLER CAMMED ENGINE.THIS JUST MAKES THE DART IRON EAGLE,PRO TOPLINE AND WORLD HEADS LOOK THAT BETTER.
12-12-2005, 01:39 PM
MainCap

Well Erik, $160.00 for this set up is considerably cheaper than going with new larger springs and the required machining to install them.

I will have a total of 410.00 in my new Vortec heads with these springs. Yes, I stole my heads from a guy that gave the pair of them up for 250.00 - unused!
12-12-2005, 02:07 PM
erik erikson

THE POINT I WAS TRYING TO MAKE WAS THE DART AND A MAJORITY OF AFTERMARKET HEADS COME MACHINED TO ACCEPT 1.550 DIA. SPRINGS.A PERSON ON THE AVERAGE WILL SPEND MORE MONEY ON SET OF VORTEC HEADS THAN THEY WOULD ON THE DARTS TO DO THE SAME THING.
12-12-2005, 02:36 PM
76GMC1500

Can't you buy the tool for $30-$40 and do it with a drill?
12-12-2005, 02:44 PM
MainCap

Not trying to be argumentative Erik, and no doubt that Dart makes great heads, but the cheapest Dart heads I found start at around 657.00/pr bare and go up from there. The assembled SS heads are 814.00/pr. For 690.00/pr you can get new Vortec's ready to run with the springs I mentioned.
12-12-2005, 02:55 PM
erik erikson

Quote:

Originally posted by MainCap
Not trying to be argumentative Erik, and no doubt that Dart makes great heads, but the cheapest Dart heads I found start at around 657.00/pr bare and go up from there. The assembled SS heads are 814.00/pr. For 690.00/pr you can get new Vortec's ready to run with the springs I mentioned.

YOU CAN BUY IRON EAGLE S/S HEADS FOR $560 A PAIR FROM COMPETITON PRODUUCTS.THE PRO TOPLINE HEADS ARE $530 WITH 2.02,1,6 VALVES AND SPRINGS GOOD TO .510 LIFT.
12-12-2005, 03:27 PM
MainCap

Erik,

Do you have a URL for Competition Products?
12-12-2005, 04:07 PM
erik erikson

Quote:

Originally posted by MainCap
Erik,

Do you have a URL for Competition Products?

YES,WWW.COMPETITIONPRODUCTS.COM OR 1-800-233-2023.
12-12-2005, 04:47 PM
MainCap

Thanks Erik.

Love the catalog cover!

Too bad the sit is under construction at the moment.